1. Manuals
  2. Brands
  3. WT Manuals
  4. Drill
  5. WTD 002
  6. Instruction manual

WT WTD 002 Instruction Manual

Ultra-precision double head extra-long drilling machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WTD 002
Ultra-precision Double Head
Instruction Manual
Extra-Long Drilling Machine
永東機械廠
永東機械廠
WING TUNG MACHINERY FTY.
WING TUNG MACHINERY FTY.
香港葵涌大連排道162-170號金龍工業中心第二期14樓G座
香港葵涌大連排道162-170號金龍工業中心第二期14樓G座
14 /F., Fiat G, State 2, Golden Dragon Industrial Centre,
14 /F., Fiat G, State 2, Golden Dragon Industrial Centre,
162-170, Tai Lin Pai Road, Kwai Chung, N.T., Hong Kong.
162-170, Tai Lin Pai Road, Kwai Chung, N.T., Hong Kong.
TEL: (852) 2426 4630 FAX: (852) 2489 9320
TEL: (852) 2426 4630 FAX: (852) 2489 9320

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WTD 002 and is the answer not in the manual?

Questions and answers

Summary of Contents for WT WTD 002

  • Page 1 WTD 002 Ultra-precision Double Head Extra-Long Drilling Machine Instruction Manual 永東機械廠 永東機械廠 WING TUNG MACHINERY FTY. WING TUNG MACHINERY FTY. 香港葵涌大連排道162-170號金龍工業中心第二期14樓G座 香港葵涌大連排道162-170號金龍工業中心第二期14樓G座 14 /F., Fiat G, State 2, Golden Dragon Industrial Centre, 14 /F., Fiat G, State 2, Golden Dragon Industrial Centre, 162-170, Tai Lin Pai Road, Kwai Chung, N.T., Hong Kong.

  • Page 2: Main Body Accessories

    Main Body 3. Mounting Handle 2. Pearl Clamp 4. Drilling Chuck 1. Drilling Roller 5. Bench Top 8. Rotary Belt 6. Locking Screw 7. Location Pin Main Body Accessories 10. Transfer Pan 9. Drilling Handle 15. Chuck Key x 2 11.Round Head Bolt x 4 14.
  • Page 3 MAIN FEATURES FOR THE COMPONENTS (Main Body) Drilling Roller – To drive the Drilling Chuck with a maximum speed of 16,000 R.P.M. Pearl Clamp – To mount up the Clamping Head in proper position. Mounting Handle – To control the movement of Pearl Clamp for mount up or release the Pearl. Drilling Chuck –...

  • Page 4: Driving Motor

    Driving Motor 4. Protective Case 1. Pulley x 2 2. Power Source Cover 3. Mounting Stand Driving Motor Accessories 5. Stepping Pan 6. L-Joint X 2 7. Round Head Bolt X 4 8. Rings X 8 9. Nuts X 4...
  • Page 5 MAIN FEATURES FOR THE COMPONENTS (Driving Motor) Pulley – To drive the Drilling Roller by connecting with the Rotary Belt. Power Source Cover – To protect the voltage terminals and avoid current leakage. Mounting Stand – For connecting the Driving Motor on the worktable. Protective Case –...
  • Page 6 PROCEDURES FOR ADJUST THE PEARL CLAMP DISTANCE The operation procedures of using WTD 002 is equal to WTD 001. This is a professional design which is ideal for drilling the longer pearl. Therefore, Auto- matic adjustment of the pearl clamp is very important. You can see the different of the...

  • Page 7: Operation Procedures

    OPERATION PROCEDURES Place and Mount the Transfer Pan onto the drilling machine by using the Step 1. Locking Screw. (See Figure 1) Figure 1 Step 2. Mount the Drilling Handle at the back of the drilling machine. (See Figure 2) Figure 2 Step 3.
  • Page 8 Step 5. Press the Mounting Handle slightly, push the Drilling Handle to the left end side, adjust the Ground Bit Inserts (use of Chuck Key) at the center posi- tion and make sure that the distance between two ends of Ground Bit Inserts is about 1 mm.
  • Page 9 Note: The voltage selection methods are shown as Figure 5. D1 and D2 are known as the input terminals. Figure 5 Step 7. Close the Power Source Cover. Assembly the Main Body and the Driving Motor on the worktable. (See Figure 6) Figure 6 Note: The worktable and the switch box shown in Figure 6 are not provided.
  • Page 10 Step 8. Place the pearl between the two Clamping Heads. Clamp the pearl on the Clamping Heads by stepped down the Stepping Pan. (See Figure 7) Figure 7 Step 9. Pull out the Drilling Handle to the Right end to ensure that the Ground Bit Inserts are located away from the pearl.
  • Page 11 Step 13. Continue to drill the pearl until the Drilling Handle is being pushed to the LEFT end and the Location Pin collided with the adjustable screw. Caution: If user found out the Pearl cannot be drilled through, please adjust the Compensation Screw (See Figure 9) which is at the right bottom side of the main body to adjust the suitable compensation distance between two Ground Bit Inserts when drilling.
  • Page 12 APPENDIX THE LAYOUT OF THE WORKTABLE TOP SURFACE Figure 10 SAMPLES FOR THE GROUND BIT INSERTS Figure 11 Figure 12...
  • Page 13 附錄 APPENDIX DIMENSIONS OF THE GROUND BIT INSERT Figure 13 SAMPLES OF THE DRILLING HEADS Figure 14...

  • Page 14: Specifications

    SPECIFICATIONS Drilling Hole Sizes Range (dia.) 0.5 – 3.0 mm (Ground Bit Insert is no provided. Please prepared by own or additional purchase) Clamping Object Size (dia.) 2.0 – 36.0 mm (Clamping Head is no provided. Please prepared by own or additional purchase) Maximum Drilling Speed 16,000 R.P.M.

Table of Contents