Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RCS Eden Series
Summary of Contents for RCS Eden Series
- Page 1 Installation & User Guide Eden Power Tray The ETL Symbol is a UK registered certification mark of the Department of Energy and Climate Change Authorised User: 03195 Installation Guide | Issue 2.0 | The Eden Power Tray Page 1...
-
Page 2: Table Of Contents
Contents The Eden Power Tray Contents 1. INTRODUCTION The Eden Power Tray Range 1.1.1 Variants / Part Codes for Ordering 1.1.2 Replacing Legacy Equipment 1.1.3 Eden Power Tray – Mating Connectors 2. CONNECTION DETAILS EP3115 & 3116 10A Assisted Defrost / Major Tray Connectivity EP3115 &... - Page 3 Contents The Eden Power Tray 6. REVISION HISTORY 7. DISCLAIMER 8. CONTACT DETAILS 9. APPENDICES Cycle Time function (Times menu (Ti13) Defrost Cycle (Fans Off) Defrost Cycle (Fans On) Integral Compressor Action Remote Display 9.5.1 Panel Cut-out 9.5.2 Remote Display 9.5.3 Retaining Clips 9.5.4 Remote Display Module 10.
-
Page 4: Introduction
All high current outputs are protected by re-settable MCB’s. Connector configurations where possible remain identical to previous RCS cabinet control panels to safeguard easy replacement of legacy units. The assisted defrost variants also provide an external connection for defrost heater klixons to provide further safety features. -
Page 5: Variants / Part Codes For Ordering
Part Codes The Eden Power Tray 1.1.1 Variants / Part Codes for Ordering This installation and set-up guide covers the complete Eden Power Tray range. The following part codes should be used at the ordering stage:- Variant Inlet Valve Type Communication Type Part No Off-Cycle defrost... -
Page 6: Replacing Legacy Equipment
Eden Power Tray Mating Connectors:- Incoming Mains Supply Connector, mates with: Weidmuller STVS3 161699 RCS Part Code KS3STVS00 Cable Clamp / Strain Relief for above connector: Weidmuller STVS3ZE 161387. RCS Part Code K00STV3ZE STV1 / 2, mates with: Weidmuller STVS3 174367. -
Page 7: Connection Details
Connection Details – 10A Assisted Defrost The Eden Power Tray 2. Connection Details EP3115, EP3125 (LSV) & EP3116, EP3126 (EEV) (10A Assisted Defrost & Major Legacy replacement) - Connectivity Details STV1 Pin Number Function Rating/Designation Earth Defrost Live 10A Internal MCB (CB 2) Defrost Neutral LSV/EEV Live 2A Internal MCB (CB 8) -
Page 8: Ep3115 & 3116 10A Assisted Defrost / Major Tray Circuit Diagram
10A Assisted Defrost Circuit Diagram The Eden Power Tray EP3115, EP3125 (LSV) & EP3116, EP3126 (EEV) (10A Assisted Defrost & Major Legacy replacement) -Circuit Diagram Installation Guide | Issue 2.0 | The Eden Power Tray Page 8... -
Page 9: Ep3113 & 3114 30A Assisted Defrost / Ktuc09Tray Connectivity
Connection Details - 30A Assisted Defrost The Eden Power Tray 2.3 EP3113, EP3123 (LSV) & EP3114, EP3124 (EEV) (30A Assisted Defrost & KTUC09 Electric Defrost Legacy replacement) - Connectivity Details STV1 Pin Number Function Rating/Designation Earth Defrost Live 10A Internal MCB (CB 2) Defrost Neutral LSV/EEV Live 2A Internal MCB (CB 8) -
Page 10: Ep3113 & 3114 30A Assisted Defrost / Ktuc09Tray Circuit Diagram
30A Assisted Defrost Circuit Diagram The Eden Power Tray 2.4 EP3113, EP3123 (LSV) & EP3114, EP3124 (EEV) (30A Assisted Defrost & KTUC09 Electric Defrost Legacy replacement) – Circuit Diagram Installation Guide | Issue 2.0 | The Eden Power Tray Page 10... -
Page 11: Ep3119 & 31110 Hot Gas Defrost / Ktuc09 Hg Tray Connectivity
Connection Details - Hot Gas Defrost The Eden Power Tray 2.5 EP3119, EP3129 (LSV) & EP31110, EP31210 (EEV) (Hot Gas Defrost & KTUC09 Hot Gas Defrost Legacy replacement) - Connectivity Details STV1 Pin Number Function Rating/Designation Earth Not Used Not Used LSV/EEV Live 2A Internal MCB (CB 8) LSV/EEV Neutral... -
Page 12: Ep3119 / 31110 Hot Gas Defrost / Ktuc09 Hg Tray Circuit Diagram
Hot Gas Defrost Circuit Diagram The Eden Power Tray 2.6 EP3119, EP3129 (LSV) & EP31110, EP31210 (EEV) (Hot Gas Defrost & KTUC09 Hot Gas Defrost Legacy replacement) - Circuit Diagram Installation Guide | Issue 2.0 | The Eden Power Tray Page 12... -
Page 13: Ep3117 & Ep3118 External Defrost Contactor / Ktuc09 Tray Connectivity
Connection Details - External Defrost Contactor The Eden Power Tray 2.7 EP3117, EP3127 (LSV) & EP3118, EP3128 (EEV) (External Defrost Contactor & KTUC09 “Tray” Legacy replacement) - Connectivity Details STV1 Pin Number Function Rating/Designation Earth Not Used Not Used LSV/EEV Live 2A Internal MCB (CB 8) LSV/EEV Neutral Fans Live... -
Page 14: Ep3117 & Ep3118 External Defrost Contactor / Ktuc09 Tray Circuit Diagram
External Defrost Contactor Circuit Diagram The Eden Power Tray 2.8 EP3117, EP3127 (LSV) & EP3118, EP3128 (EEV) (External Defrost Contactor & KTUC09 “Tray” Legacy replacement) – Circuit Diagram Installation Guide | Issue 2.0 | The Eden Power Tray Page 14... -
Page 15: Ep3111 Minor Assisted Defrost Tray Connectivity
Connection Details - Minor Assisted Defrost The Eden Power Tray 2.9 EP3111 (Minor Assisted Defrost Legacy replacement) – Connectivity Details STV1 Pin Number Function Rating/Designation Earth Defrost Live 16A Internal MCB (CB4) Defrost Neutral LSV/EEV Live 2A Internal MCB (CB 6) LSV/EEV Neutral Fans Live 2A Internal MCB (CB 5) -
Page 16: Ep3111 Minor Assisted Defrost Tray Circuit Diagram
Minor Assisted Defrost Circuit Diagram The Eden Power Tray 2.10 EP3111 (Minor Assisted Defrost Legacy replacement) – Circuit Diagram Installation Guide | Issue 2.0 | The Eden Power Tray Page 16... -
Page 17: Ep3110 & 3112 Off-Cycle Defrost Tray Connectivity
Connection Details – Off-Cycle Defrost The Eden Power Tray 2.11 EP3110, EP3120 (LSV) & EP3112, EP3122 (EEV) (Off-Cycle Defrost) Connectivity Details – STV1 Pin Number Function Rating/Designation Earth Curtain Fan Live 4A Internal MCB (CB 3) Curtain Fan Neutral LSV/EEV Live 2A Internal MCB (CB 5) LSV/EEV Neutral Fans Live... -
Page 18: Ep3110 & 3112 Off-Cycle Defrost Tray Circuit Diagram
Off-Cycle Defrost Circuit Diagram The Eden Power Tray 2.12 EP311, EP3120 (LSV) & EP3112, EP3122 (EEV) (Off-Cycle Defrost) Circuit Diagram – Installation Guide | Issue 2.0 | The Eden Power Tray Page 18... -
Page 19: All Variants - Sensor / Communication Network Connections
Connection Details – Sensors & Comms. The Eden Power Tray 2.13 All Variants – Sensor / communication network connections 12 Way BLZ Pin Number Function Rating/Designation Air On – Signal Air On – Ground Air Off Sensor – Signal Air Off Sensor – Ground Evaporator In Sensor –... -
Page 20: All Variants - Tray End View
Chassis – End View The Eden Power Tray 2.14 All Variants – End View Installation Guide | Issue 2.0 | The Eden Power Tray Page 20... -
Page 21: Setting The Controller Up
HT and LT variants. If the user wishes to confirm / modify parameters using the RCS system manager then the Eden controllers will need to be logged onto the system to achieve this, please complete the Setup and Address sections as identified on pages 8-11 before proceeding to use the system manager. - Page 22 Setting up the controller The Eden Power Tray Alarm Critical alarm present, see Alarms Menu – Page 10 Service See Parameter Ti9 – Page 18 HACCP See Parameter Su9 – Page 9 Valve Illuminated when Relay 1 is on – Pages 28-29 Fans Illuminated when Relay 2 is on - Pages 28-29 Lights...
-
Page 23: Using The Front Panel Display & Function Keys
Setting up the controller The Eden Power Tray 3.2 Using the front panel display and function keys To enter setup press the FUNCTION and UP buttons simultaneously for greater than 3 seconds until the message appears. Pressing the ENTER key again at this point will allow access to the first item in the setup menu (Su1). -
Page 24: Set Up Menu
Setting up the controller The Eden Power Tray 3.2.1 Set Up Menu Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, at this point press the ENTER button again and the display will indicate Su1. This is the first item in the set up menu. - Page 25 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information Digital Input 1 0 = Case Clean Case - Case - Default for cabinet type 3 and Function 1 = Door Open Clean - Clean 4 is case clean. If unit type 1 2 = C1 Fault or 2 selected (su1) then default value becomes 2 –...
-
Page 26: Controllers Address & Communications Menu
Setting up the controller The Eden Power Tray 3.2.2 Controller address and communications menu Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key once - the display will indicate Addr at this point press the ENTER button and the display will indicate 485A. - Page 27 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information 0 – 255 Sn -2 Sub-Net Address Byte Allows the user to set the second byte of the controllers sub net mask. Note- If DHCP is set to yes this value is not editable.
-
Page 28: Controllers Refrigeration Related Parameter Menu
Setting up the controller The Eden Power Tray 3.2.3 Controllers Refrigeration related parameter menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 2 times - the display will indicate rEF, at this point press the ENTER button and the display will indicate rF1. - Page 29 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information Superheat Setpoint 0.0 - 9.0 °C 6.0°C 6.0°C The controller will attempt to maintain this superheat setpoint N/A will be displayed if LSV version. 0 – 100% EEV Injection Sets the value of the EEV when percentage...
-
Page 30: Controllers Defrost Menu
Setting up the controller The Eden Power Tray 3.2.4 Controllers DEFROST menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 3 times - the display will indicate dEF, at this point press the ENTER button and the display will indicate dF1. - Page 31 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information Defrost termination -40.0°C - +35.0°C °C 8.0°C 8.0°C Scheduled defrost will terminate Temperature when the defrost termination sensor reaches this temperature. Note – If the defrost termination sensor is not fitted (or faulty) then defrost termination will occur when the Evap.
-
Page 32: Controllers Fan Related Parameter Menu
Setting up the controller The Eden Power Tray 3.2.5 Controllers Fan related parameter menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 4 times - the display will indicate FAns, at this point press the ENTER button and the display will indicate Fn1. - Page 33 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information Fans On setpoint -10.0°C - +30.0°C °C 50.0°C 5.0°C Cold store Only. (HT) (HT) Defrost termination sensor temperature or Air On -1.0°C -1.0°C temperature which when (LT) (LT) achieved will allow fans to be...
-
Page 34: Controllers Times Related Parameter Menu
Setting up the controller The Eden Power Tray 3.2.6 Controllers time related parameter menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the DOWN key 5 times - the display will indicate Ti, at this point press the ENTER button and the display will indicate Ti1. - Page 35 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information 0 – 120 ti11 Air Off Alarm Delay Delay for the Air Off OT alarm 00:00 – ti12 Log Probe Alarm hh:mm 00:20 00:20 Delay for the log probe alarm NOTE –...
-
Page 36: Controllers Current Status Menu
Setting up the controller The Eden Power Tray 3.2.7 Controllers current status menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key 6 times - the display will indicate StA, at this point press the ENTER button and the display will indicate St1. - Page 37 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information St12 Digital Input 2 Open Displays the current state of controllers Closed digital input 2. Function dependant upon selection made in SETUP menu – Su8 St13 Case Clean Displays if the controller is currently in case clean mode.
-
Page 38: Controllers Current Alarms Menu
Setting up the controller The Eden Power Tray 3.2.8 Controllers current alarms menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key 4 times - the display will indicate ALAr, at this point press the ENTER button and the display will indicate AL1. - Page 39 Setting up the controller The Eden Power Tray Parameter Range Units Deflt Deflt Information Logging Sensor Indicates if the controller Failure currently has a faulty Log temperature sensor. AL10 Door Open Indicates if the controller (Cold store Only) currently has a Door Open alarm Note N/A will be displayed if not type 4 or 5...
-
Page 40: Controllers Lights Related Parameter Menu
Setting up the controller The Eden Power Tray 3.2.9 Controllers lights related parameter menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key 3 times - the display will indicate LtS, at this point press the ENTER button and the display will indicate Li1. -
Page 41: Controllers Sleep Mode Menu
Setting up the controller The Eden Power Tray 3.2.10 Controller sleep mode menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SLP, Press the UP key 2 times - the display will indicate SLP, at this point press the ENTER button and the display will indicate SP1. -
Page 42: Controllers Self Test Menu
Setting up the controller The Eden Power Tray 3.2.11 Controller self test menu. Accessed by pressing and holding the FUNCTION and UP keys simultaneously for greater than 3 seconds. The display will indicate SEt, Press the UP key once - the display will indicate SELF, at this point press the ENTER button and the display will indicate SF1. -
Page 43: Cleaning Instructions
Cleaning The Eden Power Tray 4. Cleaning Only use a soft lint-free cloth. Abrasive cloths, towels, paper towels and similar items may damage the Eden controller. Keep any liquids away from the controller; don’t use aerosol sprays, solvents or abrasives. Installation Guide | Issue 2.0 | The Eden Power Tray Page 43... -
Page 44: Specification
Specification The Eden Power Tray 5. Specification 5.1 Power requirements: 220 – 240 Vac ±10% Supply Voltage Range: 50 – 60 Hz Supply Frequency: Maximum supply current: 32 Amps Typical supply current: Loading Dependant Operating temperature range: +5C to +50C Operating Humidity: 80% maximum Storage temperature range:... -
Page 45: Revision History
Revision History The Eden Power Tray 6. Revision History Revision Date Author Amendments Comments 06/08/14 First Draft Issued for internal review 06/02/15 Various Amendments Circuit Diagrams updated. Part Codes Updated. General Text Corrections. Installation Guide | Issue 2.0 | The Eden Power Tray Page 45... -
Page 46: Disclaimer
To allow for design and specification improvements, the information contained within this document is subject to change at any time without prior notice. RCS Energy Management shall not be liable for any errors or omissions, for incidental or consequential damages either directly or indirectly resulting from the misuse of this product or associated document. -
Page 47: Contact Details
Contact Details The Eden Power Tray 8. Contact Details RCS Energy Management Limited RMS House Kennet Side Newbury Berkshire RG14 5PX UNITED KINGDOM Tel: +44 (0) 1635 231600 Fax: +44 (0) 1635 231699 Email: sales@rcsenergymanagement.co.uk Website: www.rcsenergymanagement.co.uk Installation Guide | Issue 2.0 | The Eden Power Tray... -
Page 48: Appendices
Appendices The Eden Power Tray 9. Appendices Appendix 1 9.1 Cycle Time function (Times menu (Ti13) Minimum value 0 Minutes Default Value 60 Minutes Maximum value = 120 Minutes This energy saving feature applies to HT cases with liquid solenoid valve control only, and operates within the standard LSV control loop. -
Page 49: Defrost Cycle (Fans Off)
Appendices The Eden Power Tray Appendix 2 9.2 Defrost Cycle (Fans Off) Installation Guide | Issue 2.0 | The Eden Power Tray Page 49... -
Page 50: Defrost Cycle (Fans On)
Appendices The Eden Power Tray Appendix 3 9.3 Defrost Cycle (Fans On) Installation Guide | Issue 2.0 | The Eden Power Tray Page 50... -
Page 51: Integral Compressor Action
Appendices The Eden Power Tray Appendix 4 9.4 Integral Compressor Action Installation Guide | Issue 2.0 | The Eden Power Tray Page 51... -
Page 52: Remote Display
Appendices The Eden Power Tray Appendix 5 9.5 Remote Display The Eden Power Tray range is available in configurations to support remote display requirements. The Eden Compact remote display unit maintains exactly the same fascia dimensions as the compact controller. 9.5.1 Panel Cut-out: 71mm 29mm... -
Page 53: Remote Display
Appendices The Eden Power Tray 9.5.2 Remote Display The remote display unit is robustly held in position by the use of sprung clips at either end of the enclosure. These have been designed to allow the fitment of the module through a panel cut-out from the front. 9.5.3 Retaining Clips: The remote display unit maintains exactly the same functionality as the integral display variant of the Eden Compact with menu access, parameter management and setup the same as previously described within this... -
Page 54: European Declaration Of Conformity
Declaration of Conformity The Eden Power Tray 10. European Declaration of Conformity We of RCS Energy Management Limited RMS House, Kennet Side, Bone Lane, Newbury, Berkshire, RG14 5PX In accordance with the following directive(s): EN 60730-1 (Fourth Edition) 2010 Automatic electrical controls for household and similar use.
Need help?
Do you have a question about the Eden Series and is the answer not in the manual?
Questions and answers