Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LK LI-IL150
- Page 2 Thank you for purchasing product of LK Lab Korea co.,Ltd. This User Guide describes your product’s function, operation and safe use. Please read carefully and keep them in mind before you operate products. In case some parts which need extra care for users, we put some mark as below for the occasion.
-
Page 3: Table Of Contents
Contents 1. Preparation 1.1 Introduction 1.2 Feature 1.3 Structure 1.4 Installation 2. Operation 2.1 Naming and Function of Temperature Controller 2.2 FIX MODE (One Temp. Operation) 2.3 Program MODE (Multiple Temp. Operation) 2.4 Additional Function 3. Maintain 3.1 Maintaining after Use 3.2 Disorders and Solutions 3.3 After Sales Service 4. -
Page 4: Preparation
1. Preparation Instruction This product is used for bacterial culture and then cultured tissue culture experiments of various flora and fauna. It is also useful in various experiments such as thermo plant specimen storage and storage experiments, such as environmental change experiments. We consider the convenience and safety of the users through a variety of functions and a maximum of safety. -
Page 5: Structure
Structure [1] Over Temp. Limiter [8] Door Packing [2] Temperature Controller [9] Chamber 11 12 13 [3] Door [10] Power Swtich [4] Door Handle [11] Communication Port [5] Glass Door [12] Circuit Breaker [6] Shelf rail [13] Power Cord [7] Shelf [14] Lower Cover [Low Temp. - Page 6 [1] Over Temp. Limiter the temperature go over the set temperature, shut out the power of heater immediately to prevent overheat, user need to set 10% higher temperature from actual treat. [2] Temperature Controller use for controlling temperature inside. [3] Door insulation between inside and outside of chamber, prevent overheated of surface.
- Page 7 [11] Communication Port RS485 communication port. [12] Circuit Breaker Breaker of overcurrent. [13] Power Cord supply electronic power to equipment. [14] Lower Cover Lower part on the cover there are condenser inside.
-
Page 8: Installation
Installation 1.4.1 Contents of product(with delivery) ▶ Main Body(1set), Power Cord(1ea), Wire Shelf(2ea), Shelf Rail(4ea), User Guide(1copy) 1.4.2 Installation Environment ▶ - Avoid direct light. - Place where with less vibration and flat surface. - Maintain the temperature of surrounding area the product placed between 5 to 40℃. -
Page 9: Operation
2. Operation Naming and Function of Temperature Controller [1] Graphic LCD Available to check status of the equipment and display data. [2] Run Lamp Light on during the equipment operates. [3] Heater Lamp Display quantity of output with flickering. [4] Timer Lamp Light on during operate with timer. - Page 10 [8] Shift key Use for moving the position of set value and set of Auto-Tuning Mode. [9] Run/Stop key Use for operating, stop and set values. [10] Mode key Use for changing menu. [11] Display Mode User can select one between FIX(one temp.) and Program(multiple temp.) Mode.
-
Page 11: Fix Mode (One Temp. Operation)
FIX MODE(one temp. operation) / Operation Method Check the mode status and if not set as FIX MODE, press ‘UP KEY’ for 3 seconds to change FIX MODE. · Fix Mode Stand-By · SV Set Mode - Set SV Value. ·... - Page 12 · Fan Speed Set Mode - Set Speed Value. · Fix Mode Stand-By 2sec. · Start Operation / Lower setting of fan speed can cause for bigger temperature difference inside chamber.
-
Page 13: Program Mode (Multiple Temp. Operation)
Program MODE(multiple temp. operation) / Operation Method Check the mode status and if not set as PROGRAM MODE, press ‘DOWN KEY’ for 3 seconds to change PROGRAM MODE. · Program Mode Stand-By · End Step Set mode - Set number of steps. As number of steps set, user can set temperature steps. - Page 14 · Step-1 Timer Set mode - Set time value for Step – 1. · Step-1 Fan Set Mode - Set speed value for Step - 1. · Step-2 SV Set mode - Set SV Value for Step – 2. · Step-2 Timer Set mode - Set time value for Step –...
- Page 15 · Step-1 Fan Set Mode - Set speed value for Step – 2. · With same method, set values till the last step (in order of temp., time, fan speed) · Program Mode Stand-By 2sec. · Start Operation...
-
Page 16: Additional Function
Additional Function Auto Tuning is provide the best value for P.I.D Gain after calculation with considering treat environment automatically, so that user can experiment more accuracy and quickly. Calculated Gain value is saved automatically, if user wish to same experiment once again, the user need only tuning once. Auto Tuning is only available during RUN session. -
Page 17: Maintain
3. Maintain Maintaining after Use [1] After treat, Power Switch and Earth Leakage Breaker have to be turned off. [2] If the equipment contaminated plug off the Power Cord and cleaning with Alcoholic liquid. [3] If the equipment would not be used for a long time, plug off the Power Cord and cleaning and store the equipment. - Page 18 3.2.3 Temp. Control Disorder ▶ 1) Please check if the Over Temp. Limiter set 10% higher than treat value. 2) Please operate Auto-Tuning. 3) Please set the fan speed as 5 step. 4) If still not working after those solution above, contact our Technical Support Department.
-
Page 19: After Sales Service
After receipt of A/S inquiry, our technician quotes and user decides after get quoted. The product after 2 weeks from receipt of A/S inquiry without response will be return to the user. Technical Support Department of LK Lab Korea Co.,Ltd: +82 31 572 4952... -
Page 20: Specification
4. Specification Cat. no. Model Capacity Range I03-91-045 LI-IL060 60 L I03-91-055 LI-IL150 150 L 0 ~ 80℃ I03-91-065 LI-IL250 250 L I03-91-075 LI-IL450 450 L Oat. no. Cat. no. I03-91-045 I03-91-055 I03-91-065 I03-91-075 Model LI-IS060 LI-IS150 LI-IL250 LI-IL450 Capacity... - Page 21 @LKLABKorea...