Advertisement
VARTON LED Industrial Luminaires IRON, IRON ACRYL, IRON OPAL, IRON LENS IP67
for aggressive environment
Technical characteristics
Input voltage AC 220-240V, AC/DC 36V;
Lifetime 50 000 hours;
Color rendering index R
> 80;
a
Ambient temperature - 40 °C + 45 °C;
Surface/suspending mounting;
Safety class I.
Installation
The luminaire can be installed directly on a at surface made of
normally ammable material and it also can be mounted on self-sup-
porting suspensions;
Installation of VARTON® LED luminaire is to be carried out in such
a way as to provide a secure xture and a comfortable layout of lumi-
naires;
During the installation you should drill mounting holes on the
surface of the ceiling (maximum distance from hole centers equals to
the luminaire length minus 35 mm). Then insert the luminaire into lock-
ups until it clicks;
VARTON LED Industrial Luminaires OLYMP IP65
Technical characteristics
Input voltage AC220-240V, 50Hz;
Lifetime 50 000 hours;
Color temperature 5000K;
Color rendering index R
> 75;
a
Ambient temperature - 40 °C + 45 °C;
Safety class I.
Installation
Set the luminaire to the necessary turning angle;
Untwist wing nuts and remove screws from holes in the swivel
bracket. Then turn the bracket to the desired angle and install the
screws into the corresponding holes. Tighten the wing nuts on the
screws;
Install the luminaire onto the mounting surface, having fastened it
by set bolts through mounting holes. The diameter of mounting bolts
should be 10 mm;
Sizes of mounting holes for luminaires with capacity of 60,
90, 120, 150W:
For 60W – L = 150mm
For 120W – L = 260mm
For 90W – L = 260mm
For 150W – L = 360mm
Wing Nut
Wing Nut
L
Mounting Hole
Swivel Bracket
25
11
VARTON LED Industrial Luminaires OLYMP S10 IP65
Technical characteristics
Input voltage AC220-240V, 50/60Hz;
Lifetime 50 000 hours;
Color temperature 5000K;
Color rendering index R
> 75;
a
Ambient temperature - 40 °C + 45 °C;
Safety class I.
Installation
Loosen the screws p. 1;
Install the luminaire onto the mounting surface, adjust the height
of the clampings p. 2;
Tighten the screws p. 1 against stop;
Fasten the luminaire on the ceiling rails using set screws M6,
setting them into the xing holes of the clampings p. 2;
Connect the wires L, N of power cable 220V to the corresponding
power supply cable wires p. 3;
During the installation on self-supporting suspensions you should
x the cable with bolts on mounting brackets for suspensions (not
included in the kit);
Snap holders on the body; secure the body on suspensions;
Network wires should be connected to the terminal blocks that
were brought out from the luminaire body through hermetic gasket;
It is recommended to wipe a contaminated di user with a soft
tissue without the use of abrasive cleaners.
Plug in a luminaire through a connecter or a socket protected from
moisture and dust. Ensure that power output goes in accordance with
an identi cation mark. Safety class should be at least IP65. Mind
wires color-marking (brown - phase L, blue - neutral N, green / yellow
- grounding).
Sizes of mounting holes for luminaires with capacity of 180,
240, 300W:
For 180W – L = 250mm
For 300W – L = 360mm
For 240W – L = 250mm
Swivel Bracket
L
Mounting Hole
25
25
11
Wing Nut
3
A
4
Сeiling surface
2
1
L — brown wire;
N — blue wire;
Crimp the earth wire with a lug of hole diameter of 3-4 mm and set
p. 4 in the ground node between the two at washers;
Press the earth wire with a screw p. 4.
Sizes of mounting holes for luminaires
А, mm
В, mm
60W
310
285
90W
460
285
120W
460
285
VARTON LED OFFICE Luminaires recessed / surface mounting IP20/IP40/IP54
VARTON LED OFFICE Luminaires recessed / surface mounting IP20/IP40/IP54
Technical characteristics
Input voltage AC 220-240V, 50Hz;
Lifetime 50 000 hours;
Color rendering index R
> 80;
a
Ambient temperature - 40 °C + 45 °C;
Safety class I.
Installation
VARTON® LED luminaires are designed to be installed in
Armstrong, Grilliato, Ecophon, Cesal suspended ceilings, drywall ceil-
ings, suspended rack ceilings or on any at surface (depending on the
product model);
Recessed installation:
Take out the luminaire from the box;
Set the luminaire on the suspended ceiling system grids;
Connect the luminaire to the mains electrical supply through
WAGO terminal block. (Picture 1);
Secure the luminaire to the bearing surface using metal suspen-
sions (not supplied in package);
Take out di user from the box;
Place di user in the luminaire frame;
Fix di user securely in the luminaire frame using white metal bar;
Secure the metal bar to the luminaire using plastic rivets (supplied
in package);
Surface mounting:
Take out the luminaire from the box;
Connect the luminaire to the mains electrical supply through
WAGO terminal block (Picture 1);
Drill holes on the installation surface, in accordance with Luminaire
Installation Size information, stated in Technical Characteristics;
VARTON LED Street Luminaires TRIUMPH IP65
Technical characteristics:
Input voltage AC220-240V, 50Hz;
Lifetime 50 000 hours;
Color rendering index R
> 75;
a
Ambient temperature - 40 °C + 45 °C;
Maximum projected area of a luminaire exposed
to the wind 0.14 m2;
Maximum height of luminaire installation 16 m;
Safety class I.
Installation
Plug in a luminaire through a connecter or a socket protected from
moisture and dust. Ensure that power output goes in accordance with
an identi cation mark. Mind wires color-marking (brown - phase L,
blue - neutral N, green / yellow - grounding);
VARTON LED Street Luminaires URAN IP65
Technical characteristics:
Input voltage AC220-240V, 50Hz;
Lifetime 50 000 hours;
Color temperature 5000K;
Color rendering index R
> 75;
a
Ambient temperature - 40 °C + 45 °C;
Maximum projected area of a luminaire exposed to
the wind 0.14 m2;
Maximum height of luminaire installation 16 m;
Safety class I.
Sizes of the xing holes for xing the luminaire
Сlamping corner
31,5
31,5
95
95
Module 1
Module 2
Power supply
220V
Module 3
Module 4
Picture 1. Connecting the luminaire 36W to power supply
During installation of IP54 luminaire, don't forget to secure the
luminaire mounting holes with silicone gaskets (supplied in package);
Take out di user from the box;
Place di user in the luminaire frame;
Fix di user securely in the luminaire frame using white metal bar;
Secure the metal bar to the luminaire using plastic rivets (supplied
in package).
Install the luminaire onto a console with diameter ranging from 40
to 48 mm;
Align the luminaire parallel to the console and tighten it by two
screws M8 (supplied) with force of at least 8 N * m.
Advertisement
