Advarsel: Indbygning og montering af elektriske apparater må kun foretages af aut. elinstallatør. Ved fejl eller driftforstyrelser kontakt den aut. elinstallatør.
! Ret til ændringer forbeholdes !
Warning: Installation and assembly of electrical equipment must be carried out by qualified electricians. Contact a qualified electrician in the event of fault or breakdown. !
Reserving the right to make changes !
Time secondary zones
Achtung: Einbau und Montage elektrischer Geräte dürfen nur durch Elektrofachkräfte erfolgen. Wenden Sie sich bei Störungen bzw. Ausfall an einen Elektrofachkraft. !
Änderungen vorbehalten !
PIR off delay
Avertissement: L'installation et le montage d'appareils électriques doivent exclusivement être exécutés par un électricien agréé. En cas de défaut ou de perturbation du
Time 1 default 15 min
fonctionnement, contacter un installateur électricien agréé. ! Sous réserve de modifications !
Do you have a question about the DALI and is the answer not in the manual?
Questions and answers
Summary of Contents for Smartscape DALI
Page 1
L’ DA- DA+ 41-750 Presence detector 360° DALI PIR off delay Fade Time 1 default 15 min 3 sec. 41-752 Presence detector 360° DALI Slave Orientation light HVAC Time 4 default 10 min On delay 5 min Not adjustable L’...
The 360° DALI master presence detector consists of a single unit Configure the required lux level for the daylight zones, if containing a control unit for DALI devices in up to three daylight different from the factory setting. zones with dimming as a function of incident daylight and up to 10.
HVAC All LEDs (red, blue, yellow, green) will flash alternately to indicate Function descriptions that the detector has not been configured with the DALI setup. Glossary Mode 1: Daylight control of up to three zones with relay output for HVAC Mode = Application, the way in which the detector will function.
Page 4
All fittings in zones 1 - 3 are DALI-based, the fittings Separate delay (Time 2) for the HVAC output (relay) can be in zone 4 can be either with or without DALI ballast. Without DALI configured on the IR remote (41-934 accessory). Fig. 8.
Page 5
230 V via the detector's relay output. Supply to all button 1 on>1 sec.). If the daylight zones are set to manual mode DALI devices is interrupted after the expire of Time 4 (Cut-Off). ("Dim+", "Dim-") by the IR remote (41-934 or 41-935, accessory), Fig.
Relay, dry contact ........NO, 230 V, µ 16 A Mode 4 80 A/100 m sec. 2 daylight zones + 2 secondary zones + HVAC + comfort light DALI ............1-64 devices 13 V DC/200 mA Slaves ............up to 10 pcs. Zone 1 Load: Incandescent lamps ........
DALI relay that is to control HVAC or “Mode” minutes in order to warm up the fluorescent tubes, after which + ”3” if there is an external DALI relay that is to control the the individual zones are gradually dimmed before eventually Cut-Off function of all fittings.
Page 8
DALI selected. The factory setting is Automatic on/off. relays. When the detector is in test mode, the various LEDs will flash depending on which sector is activated.
Page 9
Finish by pressing “Lock/unlock” and the green LED will switch off . 20(71) Servodan A/S | Tel +45 7442 4726 | Fax + 45 7442 4035 | info@servodan.dk | www.servodan.com Smartscape Connected Lighting Systems PH:07 3357 1922 info@ssqld.com.au www.ssqld.com.au...
Page 10
1, “2” for Time 2, “3” Time 3 or “4” for Time 4. The detector will of all DALI devices and then calibrate the daylight zones before it indicate the time by a number of LED flashes.
Page 11
(Time 1) has green expired or by pressing “Auto”. 22(71) Servodan A/S | Tel +45 7442 4726 | Fax + 45 7442 4035 | info@servodan.dk | www.servodan.com Smartscape Connected Lighting Systems PH:07 3357 1922 info@ssqld.com.au www.ssqld.com.au...
Page 12
Max. 5.5 mA 41-753 NB: If a zone has been selected, e.g., “1” for zone 1 as well as Motion detector, flush mounted, DALI slave, 8 m High Max. 5.5 mA a function, e.g. “On/Off” and you want a different function, wait Ceiling, type 41-762 for four seconds to choose a new function;...
Page 13
6 mA 6 mA control, type 70-021 147.5 mA Total power consumption for the connected DALI components is < 200 mA. For more information, please contact: Smartscape Connected Lighting Systems Ph: 07 3357 1922 Fax 07 3357 9189 Email: info@ssqld.com.au...
Need help?
Do you have a question about the DALI and is the answer not in the manual?
Questions and answers