Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LongSung Technology U9507E
- Page 1 U9507E User Manual...
-
Page 2: Table Of Contents
Contents 1．Introduction..................................3 1.1 Overview ..................................3 1.2 Application scenario ................................ 3 2. U9507E interfaces................................. 4 2.1 U9507E interface summary ............................4 2.1.1 Test points..................................5 2.1.2 Mini PCIe Interface..............................6 2.1.3 RF interface................................9 2.2 U9507E interface application ............................10 2.2.1 RF antenna interface............................. 10 2.2.2 Power supply and earth............................10... -
Page 3: 1．Introduction
The frequency bands supported: U9507E LTE-TDD 38/40 1/3/5/7/8/20/28 LTE-FDD UMTS 1/5/8 It working at environment temperature： -40℃~+85℃。 1.2 Application scenario The LTE U9507E wireless module support phone book, SMS, audio, GPS and Internet access functions. The application of U9507E is as follows: Page... -
Page 4: U9507E Interfaces
2.1 U9507E interface summary supports for multimode operation: The LTE wireless module U9507E LTE,HSUPA,HSDPA, UMTS and GSM. The size of U9507E is 50.85×29.9×4.6mm. And the appearance is shown in Figure 2-1 and Figure 2-2. Figure 2-1 The front view of U9507E Page... -
Page 5: Test Points
The antenna pad which is shown as part 2 in Figure 2-1 is for GPS application; A miniPCIe interface is shown as part 3 in Figure 2-1; U9507E module also offers some test points, they are shown as part 4 in Figure 2-2 2.1.1 Test points... -
Page 6: Mini Pcie Interface
USB DATA- USIM Card Reset USIM Card Clock USIM Card Data USIM Card Power 2.1.2 Mini PCIe Interface A Mini PCIe Interface is used, two primary data interfaces are defined for PCI Express Mini Card: PCI Express and USB. For more information, please refer to the PCI Express®Mini Card Electromechanical Specification Revision 1.1 Figure 2-4 show the Mini PCIe Interface. - Page 7 Figure 2-5 The Mini PCIe Interface pin sequence of U9507E Table 2.2 The definition of Mini PCIe Interface Definition Description Remark MIC Data+ Audio Interface MIC_P* MIC Data+- Audio Interface MIC_N* Speaker Out+ Audio Interface LINEOUT_P* Speaker Out- Audio Interface...
- Page 8 UART Interface UART_RXD* Rx of UART NC RTS of UART - Ground Ground UART Interface UART_TXD* Tx of UART RESET* External Reset to U9507E Ground Ground VBAT Power Supply VBAT Power Supply Ground PCM Interface PCM_CLK* PCM CLK PCM Interface...
-
Page 9: Rf Interface
Power Supply 2.1.3 RF interface U9507E uses HRS’s U.FL-R-SMT-1(10) RF connector on the module side. There are three RF connector on U9507E,from right to left: main antenna / GPS antenna* / diversity antenna. The RF connector is showed in figure 2-6. -
Page 10: U9507E Interface Application
2.2 U9507E interface application U9507E supplies multifold functional interface by a Mini PCIe Interface, such as , USIM card interface, USB interface, audio interface*, UART interface*, PCM（Pulse Code Modulation） interface*and power supply interface and so on. The detail information will be given in the follow sections. -
Page 11: Usb Interface
35, 37, 40, 43, 50 2.2.3 USB interface 2.2.3.1 Description U9507E offers a high-speed USB interface by Mini PCIe Interface, which submits to USB 2.0 protocol. The detail information is given in table 2.4 below. Table 2.4 U9507E USB interface description... - Page 12 USB_IN of USB interface and the USB_VBUS PIN of U9507E. It is shown in figure 2-8 with the red circle 2. In the voltage protection circuit, D603 is a Zener diode with a breakdown voltage value of 5.1v which could keep the voltage on the USB_VBUS PIN...
-
Page 13: Usim Interface
U9507E supports LTE, UMTS and GSM operation mode.USIM card as well as SIM card can be used. 2.2.4.1 Description U9507E offers USIM card interface by Mini PCIe Interface. And it can be used in LTE,UMTS and GSM/GPRS/EDGE networks. The table 2.5 gives the more detail information. -
Page 14: Audio Interface
(EAR1OP,EAR1OR）. And the Audio interface here includes the earphone jack and the test points. 2.2.5.1 Description The audio signals offered by U9507E are described in the table 2.7 below. Table 2.7 U9507E audio signal description The name of the correlative SN. - Page 15 2.2.5.2 The connection between audio I/O and earphone The audio I/O signals offered by U9507E can be connected to a stereo earphone jack. The more detail information about connection between earphone jack and the Mini PCIe Interface is shown in table 2.8 below. And the information about test points is shown in table 2.1 above.
-
Page 16: Pcm Interface
5 ） In the chart J501 is a four section of earphone jack schematic diagram electric circuit, you can see audio output signal connecting difference signal while audio input signal connecting one negative signal. 2.2.6 PCM interface* U9507E offers Micro the PCM interface and the SPI interface by Mini PCIe Interface. And the SPI interface is simulated by GPIO PIN. Page... -
Page 17: Uart Interface
The reference circuit of UART interface is shown in figure 2-12. 1） As the UART of U9507E can only supply TTL level while the PC serial port level is the RS232 level, the signal level between them must use level transformation chip. The reference IC is SP3238EEA which produces by SIPEX, as... -
Page 18: Led Control
Figure 2-11. J401 is a 9 needle serial port plugs，we can use it to connect U9507E and PC. 2） For avoiding the electro-static, it is recommended to use the ESD element to the signal line of the UART socket. Just like the voltage dependent resistors RV401, RV402, RV403, RV404 and RV405 in figure 2-11.And the ESD... -
Page 19: Others
VOUT VREG_MSMP Output，1.8V U9507E offers a power supply named VREG_MSMP, its value is +1.8V and the Max. value of electric current is 100mA. EXT_RST_N is used for reset the U9507E module. And U9507E will be reseted just by putting the EXT_RST_N to GND;... -
Page 20: U9507E Key Features
1206 3. U9507E key features The U9507E module has features such as internet access, SMS, GPS, phone book and audio. The features are described in following sections. For detail information about AT commands, please make refers to the related documents. -
Page 21: Gps
AT+CPBW=[<index>] delete phone number. AT+CPBF=<findtext> find the phone number according to the findtext. 4. Application Illustration 4.1 Dial-up procedure The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E. Type AT Command/Respond Explain... -
Page 22: Sms
Disconnect the PS call 4.2 SMS 4.2.1 Message Format U9507E supports two kinds of message format, PDU and TEXT which can be set by AT command AT+CMGF, AT+CMGF=0 means PDU format, and AT+CMGF=1 means TEXT format. 4.2.2 Set Message Storage Location The command AT+CPMS=<mem1>,<mem2>,<mem3>... -
Page 23: Pdu Format
If no error: +CPMS:<mem1>,<used1>,<total1>,<mem2>,<used2>,<total2>,<mem3>,<used3>,<total3> OK If error: +CMS ERROR 4.2.3 PDU Format Sending: The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E. Type AT Command/Respond Explain AT+CSCS=" UCS2" Select TE character set... - Page 24 Receiving message: +CMTI: "SM",0 Means new received message in the memory located from index 0. Reading message： The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E. Type AT Command/Respond Explain AT+CMGR=0...
-
Page 25: Text Format
4.2.4 TEXT Format Sending: The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E.. Type AT Command/Respond Explain AT+CSCS=" GSM" Select TE character set AT+CMGF=1 Select message TXT format AT+CMGS="13572034257" Send message >... -
Page 26: Sms Service Center Address Setting
11111114 Deleting message: The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E. The type “S” means the AT Command sent to U9507E, and the type “R” means Respond from U9507E. Type... -
Page 27: Phone Book
The parameter <stat> can only be 2 for the command AT+CMGW. In TEXT Format, the parameter <fo> can be 17 and 49, the parameter <pid> can only be 0, the parameter <dcs> can be 0~31 and the parameter <vp> can be 0~255 for AT+CSMP command In TEXT Format, the parameter <stat>... -
Page 28: Find Phonebook Entries
When we want to find a entry, we can give the text of the phone number ,and according to the text, we use AT+CPBF=<findtext> to find the number we want. 4.4 AUDIO Audio functions are only available in the U9507E module. 4.4.1 Originate Call ATD<str>[;] Mobile originate call to dial a number. <str>: string of dialing digits, dialing digits:0～9 <;>... -
Page 29: 6．Declaration Of Conformity
6．Declaration of Conformity Hereby,LongSungTechnology(Shanghai) Co.,Ltd. declares that this Pivothead WearableImaging (Model No.:U9507E) i s in compliance with the essential requirements and other relevant provisions of RED 2014/53/EU. 7．Address of Manufacturer ROOM 606-A BUILDING A NO.3000 LONGDONG AVENUE FREE TRADE TEST AREA, Pudong District, Shanghai, China. -
Page 30: Appendix：mechanical Dimensions Of U9507E
Appendix：Mechanical dimensions of U9507E The following are Mechanical dimensions of U9507E bottom view, side view and top view. (Unit: mm) Top View Side View Bottom View FCC Certification Requirements. According to the definition of mobile and fixed device is described in Part 2.1091(b), this device is a mobile device. - Page 31 and must not transmit simultaneously with any other antenna or transmitter. 3.A label with the following statements must be attached to the host end product: This device contains FCC ID: XHZU9507E. 4.To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed: ❒...
- Page 32 an additional permanent label referring to the enclosed module:“Contains Transmitter Module FCC ID: XHZU9507E” or “Contains FCC ID: XHZU9507E” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.