Table of Contents
Advertisement
Quick Links
Table of content
1. General
2. Product overview
5. X-wave control for flexible Pixel LED strips (XW-D and MM-8L)
1. General
The Nexmosphere X-Wave range offers a selection of animated LED strips which can be set to a variety of animated patterns
of which the color, speed, and brightness can be adjusted. This document offers explanation, instructions, and examples of
how the X-Wave LEDs can be controlled.
The information in this document is created for users who are familiar with the Nexmosphere API and are able to control a
basic setup with a Nexmosphere API controller. If this is not the case yet, please read the general documentation on the
Nexmosphere serial API first.
2. Product overview
The X-Wave range consists out of 4 main products:
XW-L5.
The XW-L5 and XW-L9 are rigid linear LED boards which each have a fixed number of LEDS: 5 and 9. The XW-D and MM-8
are X-Wave interfaces for flexible pixel LED strips of which the amount of LEDs is variable. All examples in this document are
created to control an XW-L5 or XW-L9. The commands can also be used to control an XW-D or MM-8 with a pixel LED strip
of 5 or 9 LEDs. If a pixel LED strip with a different amount of LEDs is connected, the LED output for these example commands
will vary depending on the number of LEDs on the pixel LED strip. In section 5 (page 6) of this document, more elaborate
information on the XW-D and MM-8L is provided.
XW-D
MM-8
N e x m o s p h e r e
H i g h Te c h C a m p u s 1 0 ( M μ b u i l d i n g )
5 6 5 6 A E E i n d h o v e n • T h e N e t h e r l a n d s
XW-L9.
XW-L5
XW-L5
T + 3 1 4 0 2 4 0 7 0 7 0
E s u p p o r t @ n e x m o s p h e r e . c o m
CONTROLLING X-WAVE LEDS (API)
XW-D.
XW-L9
XW-L9
Pixel LED strip
Pixel LED strip
© 2018 Nexmosphere. All rights reserved. v1.0 / 11-18
All content contained herein is subject to change without prior notice.
MANUAL
1
1
2
2
3
4
5
6
6
MM-8L
1
Advertisement
Table of Contents
Summary of Contents for Nexmosphere X-Wave Series
-
Page 1: Table Of Contents
X-Wave LEDs can be controlled. The information in this document is created for users who are familiar with the Nexmosphere API and are able to control a basic setup with a Nexmosphere API controller. If this is not the case yet, please read the general documentation on the Nexmosphere serial API first. -
Page 2: Functionality
T + 3 1 4 0 2 4 0 7 0 7 0 © 2018 Nexmosphere. All rights reserved. v1.0 / 11-18 5 6 5 6 A E E i n d h o v e n • T h e N e t h e r l a n d s E s u p p o r t @ n e x m o s p h e r e . -
Page 3: Single Ramp Led Output
T + 3 1 4 0 2 4 0 7 0 7 0 © 2018 Nexmosphere. All rights reserved. v1.0 / 11-18 5 6 5 6 A E E i n d h o v e n • T h e N e t h e r l a n d s E s u p p o r t @ n e x m o s p h e r e . -
Page 4: Pulsing Led Output
T + 3 1 4 0 2 4 0 7 0 7 0 © 2018 Nexmosphere. All rights reserved. v1.0 / 11-18 5 6 5 6 A E E i n d h o v e n • T h e N e t h e r l a n d s E s u p p o r t @ n e x m o s p h e r e . -
Page 5: Wave Led Output
T + 3 1 4 0 2 4 0 7 0 7 0 © 2018 Nexmosphere. All rights reserved. v1.0 / 11-18 5 6 5 6 A E E i n d h o v e n • T h e N e t h e r l a n d s E s u p p o r t @ n e x m o s p h e r e . -
Page 6: Power Consumption
The duplication is done automatically and therefore all commands explained in this document are applicable. The amount of segments and LEDs per segment is adjustable, but does need to be pre-programmed at Nexmosphere. In Q2 2019 the MM-8L and XW-D will be released with additional setting-features which can be used to adjust the amount of segments and LEDs per segment via X-Talk setting commands.
Need help?
Do you have a question about the X-Wave Series and is the answer not in the manual?
Questions and answers