Advertisement
Quick Links
© Panduit Corp. 2017
PRECAUTIONS ...................................................................................................................... 1
INTRODUCTION ...................................................................................................................... 2
SYSTEM SPECIFICATIONS.................................................................................................... 4
OPTIONAL ACCESSORIES .................................................................................................... 4
GENERAL GUIDELINES FOR MAINTENANCE OF TOOLS .................................................. 5
PUMP OPERATION ................................................................................................................ 5
PREVENTIVE MAINTENANCE ............................................................................................... 6
TROUBLESHOOTING ............................................................................................................. 6
CONTACT INFORMATION ..................................................................................................... 6
specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Email:
techsupport@panduit.com
CT-902HP Family
HYDRAULIC COMPRESSION SYSTEMS
OPERATION and MAINTENANCE INSTRUCTIONS
CT-902HP PUMP SHOWN
WARNING: Read all safety warnings, instructions, illustrations and
www.panduit.com
PA27876A01
Rev. 02 3-2017
Original Instructions
Technical Support
Tel: 1-800-777-3300
Advertisement
Related Manuals for Panduit CT-902HP
Summary of Contents for Panduit CT-902HP
-
Page 1: Table Of Contents
PA27876A01 CT-902HP Family Rev. 02 3-2017 HYDRAULIC COMPRESSION SYSTEMS OPERATION and MAINTENANCE INSTRUCTIONS © Panduit Corp. 2017 Original Instructions CT-902HP PUMP SHOWN PRECAUTIONS ........................1 INTRODUCTION ........................2 SYSTEM SPECIFICATIONS....................4 OPTIONAL ACCESSORIES ....................4 GENERAL GUIDELINES FOR MAINTENANCE OF TOOLS ..........5 PUMP OPERATION ........................ -
Page 2: Precautions
CT-902HP OPERATION MANUAL © Panduit Corp. 2017 FAMILY PRECAUTIONS DANGER THE USER SHOULD BE PROPERLY TRAINED IN THE CORRECT PROCEDURES REQUIRED FOR WORK AROUND ELECTRICAL LINES WARNING: When performing any service on this pump or any of its’ components, the unit MUST be disconnected from the power supply outlet. -
Page 3: Introduction
The CT-902HP family of hydraulic pumps are capable of providing 10,000 PSI (700 bar). Panduit recommends using their CT-902HP family of hydraulic pumps with the CT-900HPH Hydraulic Pump Hose, which can crimp #8 AWG thru 1500 MCM Panduit Copper Compression Connectors; and #6 AWG thru 1000 MCM Panduit Aluminum Compression Connectors. - Page 4 CT-902HP OPERATION MANUAL © Panduit Corp. 2017 FAMILY Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
-
Page 5: System Specifications
Electrically non-conductive 10 ft. hose. Supplied pre-filled with hydraulic fluid Hydraulic Pump Hose for fast start up. PG-1 Verifies the PSI reading of the CT-902HP Hydraulic Pump. Pressure Gauge Dimensions: 228 L x 114 H x 38 W (64 dial face) (mm) 9.0 L x 4.5 H x 1.5 W (2.5 dial face) in. -
Page 6: General Guidelines For Maintenance Of Tools
1 hour before using. PUMP OPERATION Connect male hose fitting to female tool fitting. (Panduit Part No. for hose is: CT-900HPH.) Vent tank by turning air vent lever (A) [see photo on Page 2] to upright position (replace cotter pin). -
Page 7: Preventive Maintenance
Maintenance should be performed monthly, whenever possible damage has occurred, or as often as operating conditions warrant. 1. Operate CT-902HP pump on 110 volts AC only, or voltages between 95 and 120. Do not operate pump on voltages less than 95 volts, or on DC current.