Table of Contents
Advertisement
Quick Links
© Panduit Corp. 2017
PRECAUTIONS ...................................................................................................................... 1
INTRODUCTION ...................................................................................................................... 2
SYSTEM SPECIFICATIONS.................................................................................................... 4
OPTIONAL ACCESSORIES .................................................................................................... 4
GENERAL GUIDELINES FOR MAINTENANCE OF TOOLS .................................................. 5
PUMP OPERATION ................................................................................................................ 5
PREVENTIVE MAINTENANCE ............................................................................................... 6
TROUBLESHOOTING ............................................................................................................. 6
CONTACT INFORMATION ..................................................................................................... 6
specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Email:
techsupport@panduit.com
CT-902HP Family
HYDRAULIC COMPRESSION SYSTEMS
OPERATION and MAINTENANCE INSTRUCTIONS
CT-902HP PUMP SHOWN
WARNING: Read all safety warnings, instructions, illustrations and
www.panduit.com
PA27876A01
Rev. 02 3-2017
Original Instructions
Technical Support
Tel: 1-800-777-3300
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Panduit CT-902HP
Summary of Contents for Panduit CT-902HP
- Page 1 PA27876A01 CT-902HP Family Rev. 02 3-2017 HYDRAULIC COMPRESSION SYSTEMS OPERATION and MAINTENANCE INSTRUCTIONS © Panduit Corp. 2017 Original Instructions CT-902HP PUMP SHOWN PRECAUTIONS ........................1 INTRODUCTION ........................2 SYSTEM SPECIFICATIONS....................4 OPTIONAL ACCESSORIES ....................4 GENERAL GUIDELINES FOR MAINTENANCE OF TOOLS ..........5 PUMP OPERATION ........................
- Page 2 CT-902HP OPERATION MANUAL © Panduit Corp. 2017 FAMILY PRECAUTIONS DANGER THE USER SHOULD BE PROPERLY TRAINED IN THE CORRECT PROCEDURES REQUIRED FOR WORK AROUND ELECTRICAL LINES WARNING: When performing any service on this pump or any of its’ components, the unit MUST be disconnected from the power supply outlet.
- Page 3 The CT-902HP family of hydraulic pumps are capable of providing 10,000 PSI (700 bar). Panduit recommends using their CT-902HP family of hydraulic pumps with the CT-900HPH Hydraulic Pump Hose, which can crimp #8 AWG thru 1500 MCM Panduit Copper Compression Connectors; and #6 AWG thru 1000 MCM Panduit Aluminum Compression Connectors.
- Page 4 CT-902HP OPERATION MANUAL © Panduit Corp. 2017 FAMILY Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
- Page 5 Electrically non-conductive 10 ft. hose. Supplied pre-filled with hydraulic fluid Hydraulic Pump Hose for fast start up. PG-1 Verifies the PSI reading of the CT-902HP Hydraulic Pump. Pressure Gauge Dimensions: 228 L x 114 H x 38 W (64 dial face) (mm) 9.0 L x 4.5 H x 1.5 W (2.5 dial face) in.
- Page 6 1 hour before using. PUMP OPERATION Connect male hose fitting to female tool fitting. (Panduit Part No. for hose is: CT-900HPH.) Vent tank by turning air vent lever (A) [see photo on Page 2] to upright position (replace cotter pin).
- Page 7 Maintenance should be performed monthly, whenever possible damage has occurred, or as often as operating conditions warrant. 1. Operate CT-902HP pump on 110 volts AC only, or voltages between 95 and 120. Do not operate pump on voltages less than 95 volts, or on DC current.
Need help?
Do you have a question about the CT-902HP and is the answer not in the manual?
Questions and answers