Table of Contents
Advertisement
Quick Links
QTech.
Aristospray
UK & Europe
2b Stephenstown Industrial Park
HVLP Turbines.
Balbriggan
County Dublin
Ireland
Australia
27 Tatura Avenue
Gosford
NSW 2250
Email sales@aristospray.com
www.Aristospray.com
www.SprayForthedecorator.com
Phone
UK 01895 276751
Ireland 01 690 3162
Australia 1300 229 757
International +353 1690 3162
Advertisement
Table of Contents
Summary of Contents for Aristospray QTech3 HVLP
- Page 1 UK & Europe 2b Stephenstown Industrial Park HVLP Turbines. Balbriggan County Dublin Ireland Australia 27 Tatura Avenue Gosford NSW 2250 Email sales@aristospray.com www.Aristospray.com www.SprayForthedecorator.com Phone UK 01895 276751 Ireland 01 690 3162 Australia 1300 229 757 International +353 1690 3162...
-
Page 2: Table Of Contents
Getting Started Spraying Techniques Air Cap Set Selection Viscosity Guide A Word About Latex General Cleaning Aristospray (Ireland) Limited Cleaning Fluid Passages 2b Stephenstown Industrial Park, Balbriggan, County Dublin, Ireland Achieving The Desired Finish Declares that QTech3 & QTech5 HVLP Turbines... - Page 3 Consult your fluid suppliers to ensure that the basement setting. fluids being used are compatible with aluminum parts. + The operator must wear shoes and the floor must not be wet. QTech HVLP Turbine Aristospray.com...
-
Page 4: Getting Started
Position the diaphragm hole to the rear of the cup. Please allow your QTech HVLP Turbine to cool for a few minutes before The spray gun can be turned to different angles when spraying but never beyond removing the hose from the turbine manifold. horizontal. QTech HVLP Turbine Aristospray.com... -
Page 5: Spraying Techniques
For the very smallest pattern (less than 1”), you must move the gun closer to the workpiece - but don’t forget to reduce the amount of paint at the fluid adjusting knob. CAUTION | Never, for any reason, point the spray gun directly at the face, or head of a person. QTech HVLP Turbine Aristospray.com... -
Page 6: Air Cap Set Selection
Please check with the Local Authority having jurisdiction on this matter. MULTI-FLECK PAINTS, LATEX on walls, ceilings etc. Product code 10-2029 2.5mm (.098") MAXIMUM HIGH OUTPUT Heavy flows, faster coverage. LATEX HOUSE PAINT on walls etc. QTech HVLP Turbine Aristospray.com... -
Page 7: A Word About Latex
Check with the manufacturer cause the gasket to flatten out. of the coating to obtain advice on thinning their product. Unfortunately, sometimes you may encounter Technical Sales Personnel that have very little experience or knowledge about HVLP Turbine spraying. QTech HVLP Turbine Aristospray.com... -
Page 8: Cleaning Fluid Passages
We do not recommend the use of a product known as ‘Fish-Eye Drops’ which is essentially liquid silicone. Silicone will only contaminate the gun even further. Anything that comes into contact with the silicone becomes contaminated - such as; rags, aprons, bench tops, gloves. QTech HVLP Turbine Aristospray.com... -
Page 9: Spray Gun User Guide
+ Leak around side pins - use Loctite to seal + Leak through lid - remove nut under lid - use Loctite Please check with the Local Authority having jurisdiction on this matter. QTech HVLP Turbine Aristospray.com... - Page 10 Rotating Nipple Assembly 10-2094 Retaining Ring 10-2088 Nipple 10-2095 Trigger 10-2089 Spindle Valve 10-2096 Trigger Pin Parts marked with are not removable Parts marked with refer to page 10 Parts marked with are available in Kit 10-2097 QTech HVLP Turbine Aristospray.com...
-
Page 11: Turbine Care & Maintenance
Place the Hose Connector (base of the gun handle) over the shaft of the gun holder and service the turbine yourself. Contact your approved dealer or Aristospray for as shown in above illustration. Please ensure it is fully set down to the base of the technical assistance. -
Page 12: Cup Assemblies
CUP ASSEMBLIES | HOSE SUCTION CUP ITEM PART DESCRIPTION 10-2009 Complete assembly 10-2004 Cup Lid Gasket 10-2005 Plastic Diaphragm 10-2000 Pressure Tube / Check Valve 10-2059 Nylon Strainer (pack 5) 10-2007 Aluminium Cup 1000cc 10-2008 Teflon Coated Aluminium Cup 1000cc GRAVITY CUP ITEM PART DESCRIPTION...
Need help?
Do you have a question about the QTech3 HVLP and is the answer not in the manual?
Questions and answers