Subscribe to Our Youtube Channel
Related Manuals for Martin M90
Summary of Contents for Martin M90
- Page 1 Martin ® Gate Jack Opener Go to Martin Gate Jack Opener web page ® Operator’s Manual M3203...
- Page 2 Important MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO CONTAMINATION OF THE MATERIAL; USER’S FAILURE TO INSPECT, MAINTAIN AND TAKE REASONABLE CARE OF THE EQUIPMENT; INJURIES OR DAMAGE RESULTING FROM USE OR APPLICATION OF THIS PRODUCT CONTRARY TO INSTRUCTIONS AND SPECIFICATIONS CONTAINED HEREIN.
-
Page 3: Table Of Contents
Part Numbers ............. ® Martin Engineering M3203-08/12 Martin... - Page 4 Gate Jack Opener, P/N M90 ........
-
Page 5: Introduction
It comes complete with hoses and hand-held control ® valve. Martin Gate Jack Opener specifications are provided in Table I. ® Table I. Martin Gate Jack Opener Specifications Air Pressure 70 cfm at 80 to 125 psi (1982 lpm at 5.5 to 8.5 bar) Output... -
Page 6: Before Installing Gate Opener
Keep any damaged goods subject to examination. ® 2. Remove Martin Gate Jack Opener from shipping box. 3. If anything is missing, contact Martin Engineering or representative. Martin Engineering M3203-08/12 Martin Gate Jack Opener ®... -
Page 7: Installing Gate Opener
CAUTION Do not exceed 125 psi (8.5 bar) air pressure. Excessive air ® pressure may cause damage to the Martin Gate Jack Opener. Make sure air is filtered and lubricated. 1. See Figure 1. With control valve (A) in closed position, connect filtered and lubricated 80- to 125-psi (5.5- to 8.5-bar) air supply to control... -
Page 8: Troubleshooting
NOTE ® Before inserting the bar, you may need to turn the Martin Gate Jack Opener to make the stirrups perpendicular to the ground. 4. Slip a strong, rigid bar (F) through the stirrups, leaving most of the bar length protruding on the force side. -
Page 9: Part Numbers
See Figure 5 for repair assembly drawing. Item Description Part No. Qty. Gate Opener Assembly M950 Hand Valve M900 Hose Assembly M910 Air Motor Assembly M980 Capstan Extension 31627 ® Figure 3. Martin Gate Jack Opener, P/N M90 Martin Engineering M3203-08/12 Martin Gate Jack Opener ®... -
Page 10: Martin Gate Jack Opener Assembly, P/N M950
® Figure 4. Martin Gate Jack Opener Assembly, P/N M950-X (Sheet 1 of 2) Martin Engineering M3203-08/12 Martin Gate Jack Opener ®... - Page 11 1/2” -13NC x 4” Hex Head M920 NS Large Seal M976 Cap Screw 3/8” Internal Tooth Lock M931 NS Small Seal M977 Washer ® Figure 4. Martin Gate Jack Opener Assembly, P/N M950-X (Sheet 2 of 2) Martin Engineering M3203-08/12 Martin Gate Jack Opener ®...
-
Page 12: Martin ® Gate Jack Opener Assembly, P/N M950 (Repair Drawing)
Martin Engineering M3203-08/12 Martin Gate Jack Opener ®... - Page 13 Any product, process, or technology described here may be the subject of intellectual property rights reserved by Martin Engineering Company. Trademarks or service marks designated with the ® symbol are registered with the U.S. Patent and Trademark Office and may be proprietary in one or more countries or regions. Other trademarks and service marks belonging to Martin Engineering Company in the United States and/or other countries or regions may be designated with the “TM”...
- Page 14 For nearly 20 years, Martin Engineering’s Foundations™ Books have taught industry personnel to operate and maintain clean and safe belt conveyors. The Foundations™ Book, fourth edition, focuses on improving belt conveyors by controlling fugitive material. “The Practical Resource for Total Dust and Material Control,” is a 576-page hard cover volume that provides information of value to industries where the efficient handling of bulk materials is a key to productivity and profitability.
Need help?
Do you have a question about the M90 and is the answer not in the manual?
Questions and answers