Summary of Contents for Fenner QD:E Series
- Page 1 Fenner QDE User Guide 9/5/08 9:23 AM Page 1 Installation Operating Instructions...
-
Page 2: Table Of Contents
7.2. Extended parameters ERIKS Industrial Services Ltd hereby states that the Fenner electrical or mechanical including photocopying, recording or QD:E Series product range is CE marked for the low voltage by any information storage or retrieval system without 2. G 7.2.1. - Page 3 OMPATIBILITY 572B21P5 The level of integrity offered by the Optidrive control functions – for Fenner drives is designed to high standards of EMC and is fitted with 572B21P5E example stop/start, forward/reverse and maximum speed, is not an internal EMC filter as standard. This EMC filter is designed to...
- Page 4 RIVE on the same supply. • Store the Fenner QD:E drive in its box until required. Storage should be clean and dry and within the temperature range –40°C to +60°C This manual is intended as a guide for proper •...
-
Page 5: Connection Diagram
Page 8 Page 9 Fenner is a registered trademark of J.H. Fenner & Co. Limited Fenner is a registered trademark of J.H. Fenner & Co. Limited... -
Page 6: Changing Parameters
ONTROL ARAMETERS To change a parameter value press and hold the key for To allow the Fenner drive to be controlled from the keypad in a 7.1. S TANDARD PARAMETERS >1s whilst the drive displays STOP. The display changes to forward direction only, set P-12 =1: P-01, indicating parameter 01. - Page 7 Drive must be powered down, reset on the keypad or by re-enabling the drive. www.fptgroup.com www.fptgroup.com Page 12 Page 13 Fenner is a registered trademark of J.H. Fenner & Co. Limited Fenner is a registered trademark of J.H. Fenner & Co. Limited...
-
Page 8: Terminal Mode (P-12 =0)
Effectively giving 5 preset speeds that parameter value. www.fptgroup.com www.fptgroup.com Page 14 Page 15 Fenner is a registered trademark of J.H. Fenner & Co. Limited Fenner is a registered trademark of J.H. Fenner & Co. Limited... - Page 9 Further information on configuring the PI controller for typical feedback applications; please refer to the Advanced User Guide. www.fptgroup.com www.fptgroup.com Page 16 Page 17 Fenner is a registered trademark of J.H. Fenner & Co. Limited Fenner is a registered trademark of J.H. Fenner & Co. Limited...
-
Page 10: Roubleshooting
32(35)* Parameters not saved, defaults reloaded. data-F Internal memory fault. Try again. If problem recurs, refer to your local Fenner authorised distributor. Output Frequency range: 0 - P-01 (500Hz max) Analog input current out of 4-20 F Check input current in range defined by P-16. - Page 11 Fenner QDE User Guide 9/5/08 9:24 AM Page 21 Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Fenner ® QD:E www.fptgroup.com Page 20 Fenner is a registered trademark of J.H. Fenner & Co. Limited...
- Page 12 Fenner QDE User Guide 9/5/08 9:24 AM Page 23...
Need help?
Do you have a question about the QD:E Series and is the answer not in the manual?
Questions and answers
Gemini'de bir Gem oluşturdum ve ona ad verdim.Sonra da ona bir resim göstererek ''Aşkımmmmmm sana hediye aldım.''yazdım sonra uzun bir şekilde ''Aşkııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııım''dedi ve sonra altında da manualslib.com diye bir site vardı.Bu hata neden oldu?