All-in-one tualatin pentium iii/celeron single board with lcd, lvds, ac97 audio, ieee1394, dual 10/100base-tx ethernet interfaces, & 4coms (176 pages)
Summary of Contents for Evalue Technology ECM-3610
Page 1
User’ s Manual ECM-3610/3610L All-in-One VIA Eden ESP6000 Single Board with LCD, LVDS, AC97 Audio, & Dual 10/100Base-Tx Ethernet Ed. – 15 November 2004 Part No. 2047361000...
Page 2
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. Evalue Technology Inc.
Page 3
Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer Evalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Evalue Technology assumes no responsibility or...
Page 4
Evalue has come to be known. Your satisfaction is our primary concern. Here is a guide to Evalue’ s customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully. Evalue Technology Inc.
Page 5
E-mail: service@evalue-tech.com E-mail: service.europe@evalue-tech.com China Branch Office US Branch Office Evalue Technology Shanghai Inc. Evalue Technology Inc. Room 909, 9F, Section B, No.900, Suite 210, 200 Tornillo Way, Yisan Road, Caohejing Hi-tech Park, Tinton Falls, NJ 07712 Shanghai 200233, China...
Page 6
(such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. Evalue Technology Inc.
Page 7
Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 ECM-3610/3610L All-in-One VIA Eden ESP6000 Computing Module 1 Quick Installation Guide 1 Audio jacks and USB connector daughter board 1 CD-ROM contains the followings: —...
Signal Description – Serial Port 1 – COM1 in RS-232 Mode (CM2) ......25 3.7.10 Secondary LCD Panel Connector (CN1)..............25 3.7.11 Primary LCD Panel Connector (CN2)................ 26 3.7.12 Signal Description – Primary & Secondary LCD Panel Connector (CN2, CN1) ..26 Evalue Technology Inc.
Page 9
Getting Help......................48 In Case of Problems.................... 48 Main Menu......................48 4.5.1 Setup Items ....................... 49 4.5.2 Standard CMOS Setup ..................... 51 4.5.3 Advanced BIOS Features ..................54 4.5.4 Advanced Chipset Features..................58 4.5.5 Integrated Peripherals....................62 Evalue Technology Inc.
Page 10
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER ....... 143 DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP ......... 143 DISPLAY SWITCH IS SET INCORRECTLY ................ 144 DISPLAY TYPE HAS CHANGED SINCE LAST BOOT............144 Evalue Technology Inc.
Page 11
Memory test fail........................147 APPENDIX E: AWARD BIOS POST CODES..............148 APPENDIX F: AUDIO / USB DAUGHTER BOARD USER’ S GUIDE ......154 Jumper & Connector Layout ..................154 Jumper and Connector List..................154 Connector Definitions....................155 Evalue Technology Inc.
Page 12
Nov. 2004 Leo Chen 1. Update the picture of the daughter board 2. Correct to non support TV out. 3. Headquarters address updated. 4. Latest BIOS updated. 5. APPENDIX F: AUDIO/USB DAUGHTER BOARD USER’ S MANUAL updated. Evalue Technology Inc.
Customer Service department with the relevant details. 2. Introduction System Overview The ECM-3610 is a 3.5” FDD size Single Board Computer that equips with VIA Eden ESP6000 low-power integrated processor, LCD & LVDS Interfaces, AGP 4X 3D Graphics, AC97 Audio, and Dual 10/100Base-Tx Ethernet interfaces.
(2 sec. ~ 255 sec., 1 sec./step) • Power Management: Supports ATX power supply. Supports PC97, LAN wake up and modem ring-in functions. I/O peripheral devices support power saving and doze/standby/suspend modes. APM 1.2 compliant. 2 ECM-3610/3610L User’ s Manual...
Page 15
• Ethernet Interface: PCI 100/10 Mbps, IEEE 802.3U compatible • Remote Boot-ROM: For diskless system SSD Interface One CF socket supports Type I/II Compact Flash memory devices Expansion Interface One 16-bit 104-pin connector onboard ECM-3610/3610L User’ s Manual 3...
Page 16
• Typical Power Requirement: 5V @ 2.9A (with VIA C3 667MHz CPU) • Operating Temperature: 32 to 140 °F (0 to 60 °C) • Board Size: 146mm x 101mm (3.5" FDD-size) • Weight: 0.4 Kg 4 ECM-3610/3610L User’ s Manual...
ECM-3610/3610L Architecture Overview The following block diagram shows the architecture and main components of ECM-3610. The two key components on board are the VIA VT8606 North Bridge and VT82C686B super South Bridge. These two devices provide the ISA and PCI bus to which all the major components are attached.
DRAM controller can run at either the host CPU Front Side Bus frequency (100 / 133 MHz) or pseudo-synchronous to the CPU FSB frequency (PC100 with the FSB at 133 MHz or PC133 with the FSB at 100 MHz) with built-in PLL timing control. 6 ECM-3610/3610L User’ s Manual...
Page 19
TwisterT’ s advanced 128-bit 2D graphics engine delivers high-speed 2D acceleration for productivity applications. Several enhancements have been made to the 2D architecture to optimize SMA performance and to provide acceleration in all color depths. ECM-3610/3610L User’ s Manual 7...
Page 20
Support 3 SODIMMs or 6 banks for up to 1.5 GB of DRAM (256Mb DRAM technology) 64-bit data width Supports maximum 8-bank interleave (8 pages open simultaneously); banks are allocated based on LRU SDRAM X-1-1-1-1-1-1-1 back-to-back accesses 8 ECM-3610/3610L User’ s Manual...
Page 21
Motion Video Architecture High quality up/down scaler Planar to packed format conversion Motion compensation for full speed DVD playback Hardware subpicture blending and highlights Multiple video windows for video conferencing Contrast, hue, saturation, brightness and gamma controls ECM-3610/3610L User’ s Manual 9...
Page 22
Independent clock stop controls for CPU / SDRAM, AGP, and PCI bus PCI and AGP bus clock run and clock generator control VTT suspend power plane preserves memory data Suspend-to-DRAM and self-refresh power down Low-leakage I/O pads ACPI 1.0 and PCI Bus Power Management 1.1 compliant 10 ECM-3610/3610L User’ s Manual...
I/O, chip select and external SMI. Hardware monitoring subsystem for managing system / motherboard voltage levels, temperatures, and fan speeds Full System Management Bus (SMBus) interface. Two 16550-compatible serial I/O ports with infrared communications port option on the second port. ECM-3610/3610L User’ s Manual 11...
Page 24
The USB controller allows hot plug and play and isochronous peripherals to be inserted into the system with universal driver support. The controller also implements legacy keyboard and mouse support so that legacy software can run transparently in a non-USB-aware operating system environment. 12 ECM-3610/3610L User’ s Manual...
These features and others reduce cost, real estate, and design complexity. The 82559ER also includes an interface to a serial (4-pin) EEPROM and a parallel interface to a 128 Kbyte Flash memory. The EEPROM provides power-on initialization for hardware and software configuration parameters ECM-3610/3610L User’ s Manual 13...
The Compact Flash storage card is O/S independent, thus offering an optimal solution for embedded systems operating in non-standard computing environments. The Compact Flash storage card is IDE compatible and offers various capacities. 14 ECM-3610/3610L User’ s Manual...
Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static- shielded bag when they are not in the chassis. ECM-3610/3610L User’ s Manual 15...
(SODIMM). The socket uses 3.3 V unbuffered synchronous DRAM (SDRAM). SODIMM module is available in capacities of 32, 64, 128, 128 or 512 MB. The socket can be filled in the SODIMM of any size, giving your ECM-3610 single board between 32 and 512 MB of memory.
You can use J4 to clear the CMOS data if necessary. To reset the CMOS data, set J4 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. Clear CMOS (J4) Clear CMOS Protect* * default 20 ECM-3610/3610L User’ s Manual...
(and J1 to 2-3 closed), if ATX power supply is to be used. AT/ATX Power Select (ATATX1) AT P/S* ATX P/S ATATX1 * default Note: Set J1 to 2-3 closed, if AT power supply is to be used. ECM-3610/3610L User’ s Manual 21...
Clear To Send. This signal indicates that the modem or data set is ready to exchange data. Data Carrier Detect. This signal indicates that the modem or data set has detected the data carrier. Ring Indicator. This signal indicates that the modem has received a telephone ringing signal. 22 ECM-3610/3610L User’ s Manual...
Serial input. This differential signal pair receives serial data from the communication link. Received data is available in Serial Port 2 Receiver Buffer Register. 3.7.6 Pin Header Serial Port 2 Connector in RS-485 Mode (CM1) Signal Signal DATA- DATA+ ECM-3610/3610L User’ s Manual 23...
(typical 100-120 Ω). Stubs to substations should be avoided. 3.7.8 Serial Port 1 with External DB9 Connector (CM2) Signal Signal 24 ECM-3610/3610L User’ s Manual...
Data Carrier Detect. This signal indicates that the modem or data set has detected the data carrier. Ring Indicator. This signal indicates that the modem has received a telephone ringing signal. 3.7.10 Secondary LCD Panel Connector (CN1) Signal Signal 3.3V 3.3V Vcon ECM-3610/3610L User’ s Manual 25...
The principle of attachment of TFT panels is that the bits for red, green, and blue use the most significant bits and skip the least significant bits if the display interface width of the TFT panel is insufficient. 28 ECM-3610/3610L User’ s Manual...
The signals SA0 and SBHE# are used to define the data present on this bus: SBHE# SD15-SD8 SD7-SD0 Action EVEN Word transfer Byte transfer on SD15- EVEN Byte transfer on SD7- Byte transfer on SD7- 30 ECM-3610/3610L User’ s Manual...
Page 43
[19:0]. All bus masters will drive this line with a tri-state driver. The permanent master ties this line to VCC through a pull-up resistor to ensure that it is inactive during the exchange of bus masters. ECM-3610/3610L User’ s Manual 31...
Page 44
IRQ [3:7], These signals are active high signals, which indicate the presence of an interrupting PC- IRQ [9:12], AT/PC104 bus adapter. Due to the use of pull-ups, unused interrupt inputs must be masked. IRQ [14:15] 32 ECM-3610/3610L User’ s Manual...
Page 45
This active high signal is asserted during a read or write command indicating that the DMA controller has reached a terminal count for the current transfer. DACK # must be presented by the bus adapter to validate the TC signal. MASTER# This signal is not supported by the chipset. ECM-3610/3610L User’ s Manual 33...
The signal is routed directly to the LED1. 3.7.19 System Fan Connector (CN6) Signal 3.7.20 Audio Connector (CN7) Signal Signal Mic Bias Mic-In Line-In L Line-In R Line-Out L Line-Out R ECM-3610/3610L User’ s Manual 35...
GND for left and right CD. This GND level is not connected to the board GND. 3.7.24 IrDA Connector (CN9) Signal IRRX IRTX 3.7.25 Signal Description – IrDA Connector (CN9) IRRX Infrared Receiver input IRTX Infrared Transmitter output 36 ECM-3610/3610L User’ s Manual...
Write protected. This active low Schmitt input from the disk drive indicates that the diskette is write-protected. DSKCHG# Diskette change. This signal is active low at power on and whenever the diskette is removed. 38 ECM-3610/3610L User’ s Manual...
LCD brightness through the VR signal (pin 4) controlled by VR1. Please see the VR1 section for detailed circuitry information. 3.7.34 Signal Description – LCD Inverter Connector (J3) Vadj = 5V ~ 0V. ENBKL LCD backlight ON/OFF control signal. ECM-3610/3610L User’ s Manual 39...
Bi-directional clock signal used to strobe data/commands from/to the PS/2 mouse. MDAT Bi-directional serial data line used to transfer data from or commands to the PS/2 mouse. 3.7.37 Parallel Port Connector (PNT1) Signal Signal STB# AFD# ERR# INIT# SLIN# ACK# BUSY SLCT 40 ECM-3610/3610L User’ s Manual...
An active high input on this pin indicates that the printer has detected the end of the paper. This pin is pulled high internally. 3.7.40 Auxiliary Power Connector (PWR1) Signal -12v 3.7.41 Power Connector (PWR2) Signal 42 ECM-3610/3610L User’ s Manual...
Differential bi-directional data signal for USB channel 1. Clock is transmitted along with the data using NRZI encoding. The signalling bit rate is up to 12 Mbs. 5 V DC supply for external devices. Maximum load according to USB standard. ECM-3610/3610L User’ s Manual 43...
Analog output carrying the green colour signal to the CRT. For 75 O cable impedance. GREEN Analog output carrying the blue colour signal to the CRT. For 75 O cable impedance. BLUE DIG-GND Ground reference for HSYNC and VSYNC. ANA-GND Ground reference for RED, GREEN, and BLUE. 44 ECM-3610/3610L User’ s Manual...
<Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to. Press F1 To Continue, DEL to enter SETUP 46 ECM-3610/3610L User’ s Manual...
Use the left and right arrow keys to choose the menu you want to be in. 4.2.2 To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “Ø” pointer marks all sub menus. ECM-3610/3610L User’ s Manual 47...
Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. Note that a brief description of each highlighted selection appears at the bottom of the screen. 48 ECM-3610/3610L User’ s Manual...
Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While Award has designed the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. ECM-3610/3610L User’ s Manual 49...
Page 62
Use this menu to set User and Supervisor Passwords. 4.5.1.11 Save & Exit Setup Save CMOS value changes to CMOS and exit setup. 4.5.1.12 Exit Without Save Abandon all CMOS value changes and exit setup. 50 ECM-3610/3610L User’ s Manual...
Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Figure 1 : The Main Menu ECM-3610/3610L User’ s Manual 51...
Page 64
Displays the amount of conventional memory detected during boot up Extended Memory Displays the amount of extended memory detected during boot up Total Memory Displays the total memory available in the system Table 2 : Main Menu Selections 52 ECM-3610/3610L User’ s Manual...
Page 65
Max = 65535 65535 means no hard disk Min = 0 **** Landing zone Max = 65535 Min = 0 Number of sectors per track Sector Max = 255 Table 3 : Hard disk selections ECM-3610/3610L User’ s Manual 53...
This item allows you to speed up memory access. However, it depends on CPU design. Enabled Enable cache Disabled Disable cache 4.5.3.3 External Cache This item allows you to speed up memory access. However, it depends on chipset design. Enabled Enable cache Disabled Disable cache 54 ECM-3610/3610L User’ s Manual...
Page 67
Seeks disk drives during boot up. Disabling speeds boot up. Enabled Enable Floppy Seek Disabled Disable Floppy Seek 4.5.3.8 Boot Up NumLock Status Select power on state for NumLock. Enabled Enable NumLock Disabled Disable NumLock ECM-3610/3610L User’ s Manual 55...
Page 68
Once the security is disabled, the system will boot and you can enter Setup freely. 4.5.3.14 OS Select for DRAM > 64MB Select the operating system that is running with greater than 64MB of RAM on the system. The choice: Non-OS2, OS2. 56 ECM-3610/3610L User’ s Manual...
Page 69
Optional shadow is disabled 4.5.3.17 Small Logo (EPA) Show This item allows you enabled/disabled the small EPA logo show on screen at the POST step, Enabled EPA Logo show is enabled Disabled EPA Logo show is disabled ECM-3610/3610L User’ s Manual 57...
This item allows you to select the SDRAM timing value by SPD data. The Choice: Enabled, Disabled. 4.5.4.2 DRAM Clock This item allows you to set DRAM clock speed. The Choice: Host CLK, HCLK-33M, HCLK+33M. 58 ECM-3610/3610L User’ s Manual...
Page 71
However, if any program writes to this memory area, a system error may result. The Choice: Enabled, Disabled. 4.5.4.9 Frame Buffer Size Select the size of onboard video controller’ s frame buffer. The buffer size are share from system memory unit. The Choice: 2M, 4M, 8M, 16M, 32M. ECM-3610/3610L User’ s Manual 59...
Page 72
The choice: Enabled, Disabled. 4.5.4.17 USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard that want to using in DOS mode. The choice: Enabled, Disabled. 60 ECM-3610/3610L User’ s Manual...
Page 73
The Choice: Auto , Disabled. 4.5.4.19 PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The choice: Enabled, Disabled. ECM-3610/3610L User’ s Manual 61...
IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, or Mode 4. 62 ECM-3610/3610L User’ s Manual...
Page 75
IR Function Duplex Select the value required by the IR device connected to the IR port. Full-duplex mode permits simultaneous two-direction transmission. Half-duplex mode permits transmission in one direction only at a time. The Choice: Half, Full. ECM-3610/3610L User’ s Manual 63...
Page 76
This item allows you to enable or disable the onboard audio function is compatible with sound blaster mode. The choice: Enable, Disable. 4.5.5.19 SB I/O Base Address This chipset traps I/O accesses for Sound Blaster compatibility at 220H, 240H, 260H, or 280H. The choice: 220H, 240H, 260H, 280H. 64 ECM-3610/3610L User’ s Manual...
Page 77
This item allows you to enable or disable MPU-401 function. The choice: Enable, Disable. 4.5.5.23 MPU-401 I/O Base Address This chipset traps I/O accesses for ROLAND MPU 401 UART interface at 330H, 300H, or Disable. The choice: 300-303H, 310-313H, 320-323H, 330-333H. ECM-3610/3610L User’ s Manual 65...
The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. 4.5.6.1 ACPI Function This item allows you to enable/disable the ACPI function. The choice: Enable, Disable. 66 ECM-3610/3610L User’ s Manual...
Page 79
This option only writes blanks to the video buffer. DPMS Initial display power management signaling. 4.5.6.5 MODEM Use IRQ This determines the IRQ in which the MODEM can use. The choice: 3, 4, 5, 7, 9, 10, 11, or NA. ECM-3610/3610L User’ s Manual 67...
Page 80
4.5.6.8.2 DisableRTC Alarm Function When Enabled, your can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend mode. 68 ECM-3610/3610L User’ s Manual...
Plug and Play operating system such as Windows®95. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “Ø”). The choice: Auto, Manual. ECM-3610/3610L User’ s Manual 69...
Page 82
This item allows you to Enable or Disable assign an IRQ for onboard VGA controller. The Choices : Enabled, Disabled. 4.5.7.10 Assign IRQ for USB This item allows you to Enable or Disable assign an IRQ for onboard USB Controller. The Choices : Enabled, Disabled. 70 ECM-3610/3610L User’ s Manual...
The choice: Enable, Disable. 4.5.8.3 Spread Spectrum This item allows you to enabled Spread Spectrum Modulated. The choice: Enable, Disable. 4.5.8.4 CPU Host Clock (CPU / PCI) This item allows you to select the CPU host clock frequency. ECM-3610/3610L User’ s Manual 71...
Load Optimized Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Pressing ‘ Y’ loads the default values that are factory settings for optimal performance system operations. 72 ECM-3610/3610L User’ s Manual...
Features Setup Menu and its Security option (see Section 3). If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup. ECM-3610/3610L User’ s Manual 73...
The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. After saving the values the system is restarted again. 74 ECM-3610/3610L User’ s Manual...
Page 87
Pressing <Enter> on this item asks for confirmation: This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer. ECM-3610/3610L User’ s Manual 75...
• Click the ‘ Start’ button, click on ‘ Settings’ and on ‘ Control panel’ to open the control panel. Your display should now look as below (possibly with different size and icons): • Double click the ‘ System’ icon (highlighted above). • Select the ‘ Device Manager’ tab. 76 ECM-3610/3610L User’ s Manual...
Page 89
Ethernet Controller adapters. This is done by selecting the line and clicking the ‘ Remove’ button. Before removal of the adapter(s), your screen might look like this: • When all adapters are removed (or none were present), a new driver can be installed. Reboot the computer. ECM-3610/3610L User’ s Manual 77...
Page 90
User’ s Manual During the boot the network adapter should be detected as shown below: 78 ECM-3610/3610L User’ s Manual...
Page 91
ECM-3610/3610L Specify the location of network adapter and click ‘ Next’ (see below). If your CPU board using Realtek RTL8139C Network chip, the location of network adapter is shown as below ECM-3610/3610L User’ s Manual 79...
Page 92
User’ s Manual Click the ‘ Next’ button. 80 ECM-3610/3610L User’ s Manual...
Page 93
Depending on the configuration, a request for the windows disks or CD-ROM may be necessary. Insert the disk / CD-ROM and click the ‘ OK’ button. An entry of the directory for the files may then be required. After typing the path name, click the ‘ OK’ button. ECM-3610/3610L User’ s Manual 81...
Page 94
Further configuration of the adapter may be made in the ‘ Advanced’ section of the driver properties. These options may be accessed through the ‘ Network’ icon in the control panel (Select the network adapter, click the ‘ Properties’ button and select the ‘ Advanced’ tab). 82 ECM-3610/3610L User’ s Manual...
The following procedures describe the steps to install the Network adapter driver on Windows NT 4.0. 1. Click the ‘ Start’ button on the task bar. Select ‘ Settings’ and ‘ Control Panel’ to start the control panel shown below: ECM-3610/3610L User’ s Manual 83...
Page 96
3. Click the ‘ Add...’ button, and the following window should appear. 4. Click the ‘ Have Disk… ’ button to install the Network adapter driver from CD-ROM. A window as the one shown below should now appear. 84 ECM-3610/3610L User’ s Manual...
Page 97
ECM-3610/3610L 5. Locate the path of Network adapter driver and click the ‘ OK’ button. ECM-3610/3610L User’ s Manual 85...
Page 98
User’ s Manual 6. Select the ‘ Realtek RTL8139(A/B/C) PCI Fast Ethernet Adapter’ or ‘ Intel GD82559ER Ethernet Adapter’ from the list (as shown below) and click the ‘ OK’ button. 86 ECM-3610/3610L User’ s Manual...
Page 99
7. If your hardware using Intel-82559ER Ethernet controller, please proceed to 12. 8. Select the ‘ (1) Auto’ to set RTL8139C Ethernet controller to Auto Duplex Mode (as shown below) and click the ‘ OK’ button. 9. Click ‘ Close’ to accept the settings. ECM-3610/3610L User’ s Manual 87...
Page 100
User’ s Manual 10. Protocols, Services etc. may now be installed and configured for the network to be used. An example is shown below. 11. If your hardware using Realtek RTL8139C Ethernet controller, please proceed to 17. 88 ECM-3610/3610L User’ s Manual...
Page 101
ECM-3610/3610L 12. System will show as below. ECM-3610/3610L User’ s Manual 89...
Page 102
13. Files from your NT-distribution will now be needed. You may have to insert the CD- ROM and specify a directory of the files. An example is shown below. 14. Protocols, Services etc. may now be installed and configured for the network to be used. An example is shown below. 90 ECM-3610/3610L User’ s Manual...
Page 103
ECM-3610/3610L 15. Click ‘ Next’ to accept the settings. ECM-3610/3610L User’ s Manual 91...
Page 104
User’ s Manual 16. Click ‘ Next’ button. The network driver should now be installed. 17. To complete the installation, reboot the computer by clicking the ‘ Yes’ button in the window shown below. 92 ECM-3610/3610L User’ s Manual...
Adapter’ . 1. Start the control panel by clicking the ‘ Start’ button, click‘ Settings’ and ‘ Control Panel’ from the sub-menu. Double click the ‘ System’ icon in the control panel as shown below. ECM-3610/3610L User’ s Manual 93...
Page 106
User’ s Manual 2. On the System properties window, click the ‘ Hardware’ tab as shown below. 94 ECM-3610/3610L User’ s Manual...
Page 107
ECM-3610/3610L 3. Click the ‘ Device Manager… ’ button to show the Device Manager. ECM-3610/3610L User’ s Manual 95...
Page 108
User’ s Manual 4. Double click ‘ Ethernet Controller’ . This will show the following window. Click the ‘ Reinstall Driver’ button. 96 ECM-3610/3610L User’ s Manual...
Page 109
ECM-3610/3610L 5. Click the ‘ Next’ button to run upgrade device driver wizard. 6. Click the ‘ Next’ button to continue the driver installation. ECM-3610/3610L User’ s Manual 97...
Page 110
7. Select the ‘ Specify a location’ check item, click the ‘ Next’ button to continue. 8. The directory for the drivers may now be entered or click the ‘ Browse… ’ button to select the directory. Click the ‘ OK’ button to continue. 98 ECM-3610/3610L User’ s Manual...
Page 111
ECM-3610/3610L 9. After system search the driver, click the ‘ Next’ button to continue the driver upgrade. ECM-3610/3610L User’ s Manual 99...
Page 112
User’ s Manual 10. After driver has been installed to system, the follow windows should appear, click the ‘ Finish’ button to finish the driver installation. 100 ECM-3610/3610L User’ s Manual...
Page 113
ECM-3610/3610L 11. After finish the driver installation, system will return to Properties windows as shown below. Click the ‘ Close’ button to return the Device Manager. ECM-3610/3610L User’ s Manual 101...
1. Click the ‘ Start’ button on the task bar, select ‘ Settings’ and ‘ Control Panel’ from the sub-menu. This should start the Control Panel as shown below: 2. Double click the ‘ Display’ icon and select the ‘ Settings’ tab as shown below. 102 ECM-3610/3610L User’ s Manual...
Page 115
‘ Change… ’ button in the Adapter Type frame to select another driver. Your display will probably have another driver then the ‘ Standard PCI Graphics Adapter (VGA)’ installed at this moment. 4. Click the ‘ Next’ to update the display driver. ECM-3610/3610L User’ s Manual 103...
Page 116
User’ s Manual 5. Click the ‘ Next’ to continue the display driver installation. 6. Locate the path of Graphics adapter driver and click the ‘ Next’ button. 104 ECM-3610/3610L User’ s Manual...
Page 117
ECM-3610/3610L 7. The driver files will now be read and the display adapter is shown as the following. Click the ‘ Next’ button to install the display driver. 8. Click the ‘ Finish’ button. ECM-3610/3610L User’ s Manual 105...
Page 118
10.Further configuration of the display adapter may be made from the ‘ Display Properties’ window (follow step 1 above). The ‘ Settings’ tab allows you to change resolution, number of colours etc. 106 ECM-3610/3610L User’ s Manual...
1. Start the control panel by clicking the ‘ Start’ button, click ‘ Settings’ and ‘ Control Panel’ from the sub-menu. Double click the ‘ Display’ icon in the control panel as shown below. 2. On the Display properties window, click the ‘ Settings’ tab as shown below. ECM-3610/3610L User’ s Manual 107...
Page 120
User’ s Manual 3. Click the ‘ Display Type… ’ button and the following window should appear. Click the ‘ Change… ’ button to select another driver. 4. Click the ‘ Have Disk… ’ button. 108 ECM-3610/3610L User’ s Manual...
Page 121
Insert the ‘ Display driver disk’ and click ‘ OK’ . 6. The display driver should now be listed as shown below. Click ‘ OK’ to accept. 7. Since this driver is not part of the NT4.0 package, the following message will be shown. ECM-3610/3610L User’ s Manual 109...
Page 122
(opened by following steps 1 and 2 shown above). An example is shown below. 12.Before accepting the new settings by pressing ‘ OK’ , a test should be performed by clicking the ‘ Test’ button. 110 ECM-3610/3610L User’ s Manual...
The driver installation may be performed by following steps shown below: 1. Start the control panel by clicking the ‘ Start’ button, click ‘ Settings’ and ‘ Control Panel’ from the sub-menu. Double click the ‘ System’ icon in the control panel as shown below. ECM-3610/3610L User’ s Manual 111...
Page 124
User’ s Manual 2. On the System properties window, click the ‘ Hardware’ tab as shown below. 3. Click the ‘ Device Manager… ’ button to show the Device Manager. 112 ECM-3610/3610L User’ s Manual...
Page 125
ECM-3610/3610L 4. Double click ‘ Video Controller (VGA Compatible)’ . This will show the following window. Click the ‘ Reinstall Driver’ button. ECM-3610/3610L User’ s Manual 113...
Page 126
User’ s Manual 5. Click the ‘ Next’ button to run upgrade device driver wizard. 6. Click the ‘ Next’ button to continue the video driver installation. 114 ECM-3610/3610L User’ s Manual...
Page 127
7. Select the ‘ Specify a location’ check item, click the ‘ Next’ button to continue. 8. The directory for the drivers may now be entered or click the ‘ Browse… ’ button to select the directory. Click the ‘ OK’ button to continue. ECM-3610/3610L User’ s Manual 115...
Page 128
User’ s Manual 9. After system search the driver, click the ‘ Next’ button to continue upgrade driver. 116 ECM-3610/3610L User’ s Manual...
Page 129
10. After the driver has been installed to system, the follow windows should appear, click the ‘ Finish’ button to finish the driver installation. 11. To complete the driver installation, reboot the computer by clicking the ‘ Yes’ button in the window shown below. ECM-3610/3610L User’ s Manual 117...
1. Click the ‘ Start’ button on the task bar, select ‘ Run’ and specify the location of VIA AC97 Audio driver setup program. This should start the VIA AC97 Audio driver setup program as shown below: 118 ECM-3610/3610L User’ s Manual...
Page 131
ECM-3610/3610L 2. Select ‘ Install driver’ as shown below. Click the ‘ Finish’ button to complete the driver setup. ECM-3610/3610L User’ s Manual 119...
Page 132
User’ s Manual Click the ‘ Next’ to update the audio driver. Click the ‘ Next’ to continue the audio driver installation. 120 ECM-3610/3610L User’ s Manual...
Page 133
Locate the path of Audio adapter driver and click the ‘ Next’ button. The driver files will now be read and the audio adapter is shown as the following. Click the ‘ Next’ button to install the audio driver. ECM-3610/3610L User’ s Manual 121...
Page 134
User’ s Manual Click the ‘ Finish’ button to complete the display driver installation. 122 ECM-3610/3610L User’ s Manual...
1. Click the ‘ Start’ button on the task bar, select ‘ Run’ and specify the location of VIA AC97 Audio driver setup program.This should start the VIA AC97 Audio driver setup program as shown below: ECM-3610/3610L User’ s Manual 123...
Page 136
User’ s Manual 2. Select ‘ Install driver’ as shown below. 124 ECM-3610/3610L User’ s Manual...
Page 137
ECM-3610/3610L 3. Select ‘ OK’ as shown below. 4. Click the ‘ Add… ’ button to install the audio driver. ECM-3610/3610L User’ s Manual 125...
Page 138
5. Select the ‘ VIA PCI Audio controller’ and click ‘ OK’ to install the audio driver. 6. Click ‘ Don’ t Restart Now’ to continue the audio driver installation. 7. Click the ‘ Add… ’ button to install the audio driver. 126 ECM-3610/3610L User’ s Manual...
Page 139
8. Select the ‘ VIA MIDI External Port Device’ and click ‘ OK’ to install the audio driver. 9. Click ‘ Don’ t Restart Now’ to continue the audio driver installation. 10. Click the ‘ OK’ button as shown below. ECM-3610/3610L User’ s Manual 127...
Page 140
User’ s Manual 11. Select ‘ Yes, I want to restart my computer now.’ and click the ‘ OK’ button to complete the audio driver installation. 128 ECM-3610/3610L User’ s Manual...
1. Click the ‘ Start’ button on the task bar, select ‘ Run’ and specify the location of VIA AC97 Audio driver setup program. This should start the VIA AC97 Audio driver setup program as shown below: ECM-3610/3610L User’ s Manual 129...
Page 142
User’ s Manual 2. Select ‘ Install driver’ as shown below. 3. Click the ‘ Finish’ button to complete the driver setup. 130 ECM-3610/3610L User’ s Manual...
Page 143
ECM-3610/3610L 4. After running setup program, the audio driver will be automatic installed completely. 5. After the audio driver installation, the system properties will be shown as below. ECM-3610/3610L User’ s Manual 131...
User’ s Manual Appendix B: System Resources Memory Map The following table indicates memory map of ECM-3610. The address ranges specify the runtime code length. Address Range Description Note 00000000h-0009FFFFh System board extension for ACPI BIOS 000A0000h-000AFFFFh S3 Graphics Twister...
The usage of these I/O addresses depends on the choices made in the Evalue setup screen. The I/O addresses are fully usable for PC/104 interface if the corresponding on-board unit is disabled in the setup screen. ECM-3610/3610L User’ s Manual 135...
The interrupts are fully useable for PC/104 interface if the corresponding on-board unit is disabled in the BIOS setup. 2. These interrupt lines are managed by the PnP handler and are subject to change during system initialisation. 136 ECM-3610/3610L User’ s Manual...
The usage of these DMA-channels depends on the choices made in the Evalue setup screen. The DMA-channels are fully usable for both PC/104 interface and PCI slot if the corresponding on-board unit is disabled in the setup screen. ECM-3610/3610L User’ s Manual 137...
Appendix C: Programming the Watchdog Timer Introduction The ECM-3610 onboard watchdog timer uses an 8-bit counter, so it has 256 resolution and the time range is from 1 second to 255 seconds with a resolution of 1 second. When the timer is setting and time-out occurs, it will trigger the hardware reset signal or interrupt signal (only IRQ 10 and IRQ 11), when you setting the time-out trigger event is hardware reset, a system reset will happen.
ECM-3610/3610L Demo Program 1 (Micro-Assembly Language) ;;============================================================== ;; Title : ECM-3610 WatchDog Timer Demo Program (15 seconds) ;; Company : Evalue Technology Inc. ;; Date : 08/12/2002 ;;============================================================== .model small .code TIMER_SET_PORT 443H TIMEOUT_CTL_PORT DW 444H ;;--------------------------------------------------- ;; Main Program start ;;---------------------------------------------------...
Page 152
SET_TIME_OUT_MODE PROC PUSH DX, CS:TIMEOUT_CTL_PORT DX, AL SET_TIME_OUT_MODE ENDP ;;--------------------------------------------------- ;;--------------------------------------------------- ;; Write watchdog timer to port 443h ;; al : value ;;--------------------------------------------------- SET_WATCHDOG_TIMER PROC PUSH DX, CS: TIMER_SET_PORT DX, AL SET_WATCHDOG_TIMER ENDP ;;--------------------------------------------------- WATCHDOG 140 ECM-3610/3610L User’ s Manual...
ECM-3610/3610L Demo Program 2 (C Language) //============================================================== // Title : ECM-3610 WatchDog Timer Test Utility // Company : Evalue Technology Inc. // Programer: Winston Kang // Version : 1.0 // Date : 08/12/2002 // Compiler : Borland C ++ //============================================================== #include <stdio.h>...
Page 154
*ptr; printf("ECM-3610 WatchDog Timer Test Utility Version 1.0 \n"); printf("Copyright (c) 2002 Evalue Technology Inc.\n"); printf("(only support ECM-3610 board and will reset the system)\n"); if (argc == 1) { printf("\n Syntax: 3610WDT [step] \n"); printf(" step range : 0 ~ 255 steps \n");...
Then reboot the system. DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP Type of diskette drive installed in the system is different from the CMOS definition. Run Setup to reconfigure the drive type correctly. ECM-3610/3610L User’ s Manual 143...
Cannot find or initialize the floppy drive controller. make sure the controller is installed correctly and firmly. If there are no floppy drives installed, be sure the Diskette Drive selection in Setup is set to NONE. 144 ECM-3610/3610L User’ s Manual...
ERROR messages when the segment that has caused the problem cannot be isolated. OFFENDING SEGMENT: This message is used in conjunction with the I/O CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused the problem has been isolated. ECM-3610/3610L User’ s Manual 145...
The board ID does not match the ID stored in the EISA non-volatile memory. NOTE: When this error appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility. 146 ECM-3610/3610L User’ s Manual...
System will repeat POST procedure infinitely while the P15 of keyboard controller is pull low. This is also used for M/B burn in test. BIOS ROM checksum error - System halted. The checksum of ROM address F0000H-FFFFFH is bad. Memory test fail. ECM-3610/3610L User’ s Manual 147...
F000 for ESCD & DMI support. Reserved Use walking 1’ s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for override. 148 ECM-3610/3610L User’ s Manual...
Page 161
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address. 2. Initialize the APIC for Pentium class CPU. 3. Program early chipset according to CMOS setup. Example: onboard IDE controller. 4. Measure CPU speed. 5. Invoke video BIOS. ECM-3610/3610L User’ s Manual 149...
Page 162
Test 8259 functionality. Reserved Reserved Reserved Initialize EISA slot Reserved 1. Calculate total memory by testing the last double word of each 64K page. 2. Program writes allocation for AMD K5 CPU. Reserved Reserved Reserved Reserved 150 ECM-3610/3610L User’ s Manual...
Page 163
Reserved Reserved Reserved Initialize PS/2 Mouse Reserved Prepare memory size information for function call: INT 15h ax=E820h Reserved Turn on L2 cache Reserved Program chipset registers according to items described in Setup & Auto-configuration table. ECM-3610/3610L User’ s Manual 151...
Page 164
3. Switch screen back to text mode 4. Set up ACPI table at top of memory. 5. Invoke ISA adapter ROMs 6. Assign IRQs to PCI devices 7. Initialize APM 8. Clear noise of IRQs. 152 ECM-3610/3610L User’ s Manual...
Page 165
2. Update keyboard LED & typematic rate 1. Build MP table 2. Build & update ESCD 3. Set CMOS century to 20h or 19h 4. Load CMOS time into DOS timer tick 5. Build MSIRQ routing table. Boot attempt (INT 19h) ECM-3610/3610L User’ s Manual 153...
2.54mm USB 2.0 connector 2 5 x 2 header, pitch 2.0mm 2.0mm USB connector 1-3, 2-4 Speaker out Line out / Speaker out select 3-5, 4-6 Line out (Default) 8 x 2 header, pitch 2.54mm TV / Audio connector 154 ECM-3610/3610L User’ s Manual...
2.0mm USB Connector (JP5) USBGND VCC1 Signal VCC2 USBGND Signal TV / Audio Connector (JP7) TVGND TVGND Line-In L SPK L Line-Out L Signal COMP Cout Yout Line-In R SPK R Line-Out Mic Bais Signal ECM-3610/3610L User’ s Manual 155...
Need help?
Do you have a question about the ECM-3610 and is the answer not in the manual?
Questions and answers