Advertisement
U S E R G U I D E
MiJET™
www.mijet.com
For technical questions:
Phone: 585-637-3760
Email: technical@mijet.com or visit www.mijet.com
For sales questions contact:
Jeff Gagnon
VP of Sales
MiJET Division of Custom Service Solutions, Inc.
Phone: 585-472-6294
Fax: 207-345-3171
Email: jeff@mijet.com
Product of:
U S E R G U I D E
M I J E T
WA S H S TAT I O N
EASY TO GET STARTED
Ready to use with one existing air line.
All-in-one workstation powered by air
Date:
Advertisement
Table of Contents
Summary of Contents for MiJET WASHSTATION
- Page 1 Phone: 585-637-3760 Email: technical@mijet.com or visit www.mijet.com For sales questions contact: Jeff Gagnon VP of Sales MiJET Division of Custom Service Solutions, Inc. Phone: 585-472-6294 Fax: 207-345-3171 Email: jeff@mijet.com EASY TO GET STARTED Ready to use with one existing air line.
- Page 2 Fluid Filter Replacement for Washstations only. Needed 15-118 9.63“ H x 2.63” dia. A MiJET unit comes with a 1/4” FNPT fitting for connecting to an existing shop air line. A high–flow quick-connect adaptor can be attached for ease of use, however, to ensure a sufficient air Custom MiJET Filter, for 12”...
-
Page 3: Table Of Contents
Removing MiJET from Table ………….…..Page 10 OSHA compliant Maintenance ………………….…….……... Page 12 Stainless Steel Parts Basket— Installing the Air Deflector ………….……... Page 16 Fine Mesh, for 12” dia. MiJET angled top 15-107 workstation and wash station Troubleshooting …………………….……... Page 17 13.5” x 7.25” x 9.75”... -
Page 4: Mijet Diagram
A: Ensure all fittings and connections are correct, if so, try connecting the MiJET to the air supply line without use of any quick-disconnect fitting. Try connecting an airline from the main air supply to the MiJET with a large enough diameter (3/8”) air hose to supply enough CFM to the unit. - Page 5 Figure 20 directly to air supply 3. Place the air deflector into the or use high- MiJET. Try to line-up the hole flow quick Air filter connect on the air deflector (Figure 21) with the hole on the MiJET.
-
Page 6: Air Supply Requirements
5. Reassemble bucket lid adapter with three (3) nuts, taking consider the following: care not to over tighten and crush the filter shown in Figure 18. The air hose to the MiJET should be as short as practical and at least 3/8 inch diameter, (larger is better). ... -
Page 7: Instructions
4. Lift up the bucket filter adapter (seen at bottom of picture, 4. Connect shop air hose to the MiJET, location shown in the gray plastic ring) and remove filter seen on the left in Figure Figure 2a. - Page 8 Replace MiJET filter, P/N 13-041, per the following instructions. MiJET can be installed down the line from an oiler. 1. Disconnect shop air supply and unlatch the two metal 6. Hold the part to be cleaned as far as possible into the tabs as seen in Figure 14.
-
Page 9: Using The Faucet
1. Utilize the faucet by turning on the valves to allow flow. After 5000 parts cleaned or monthly: Refer to the MiJET Diagram on Page 4 and 5 if necessary. 1. To ensure proper performance of the Wash Station, regular 2. -
Page 10: Removing Mijet From Table
6. Remove both handles, shown in Figure 9. 12. Reassemble after all maintenance is complete. 13. Remember to refill the cleaning solution before connecting the MiJET up to the shop air. Reconnect airline and continue to clean parts. Figure 9 Page 10...
Need help?
Do you have a question about the WASHSTATION and is the answer not in the manual?
Questions and answers