Timer Operation - Fujitsu ABYG-LRTA Series Operating Manual

TIMER OPERATION

Before using the timer operation, be sure that the remote controller is set to the correct current time (
If the indoor unit is connected to a wired remote controller, the wireless remote controller cannot be used to set the timer.
NOTES: In simultaneous multi connection, this function by using the wireless remote controller cannot be used.
To use On Timer or Off Timer
1
Press the "START/STOP" button
(if the unit is already operating, proceed to step 2).
The indoor unit's Operation indicator lamp (green) will light.
2
Press the "TIMER MODE" button to select the Off
Timer or the On Timer operation.
Each time the button is pressed the timer function changes in the following
order:
PROGRAM ([OFF → ON], [OFF ← ON])
The indoor unit's Timer indicator lamp (orange) will light.
3
Use the "TIMER" Set buttons to adjust the desired Off
time or On time.
Set the time while the clock indicator is blinking (the blinking will continue for
about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To use Program Timer
1
Press the "START/STOP" button
(if the unit is already operating, proceed to step 2).
The indoor unit's Operation indicator lamp (green) will light.
2
Set the desired times for Off Timer and On Timer.
See the section "To use On Timer or Off Timer" to set the desired mode and
times.
About 3 seconds later, the entire display will reappear.
The indoor unit's Timer indicator lamp (orange) will light.
3
Press the "TIMER MODE" button to select the Program
Timer operation ([OFF → ON] or [OFF ← ON] will
display).
The display will alternately show [OFF] and [ON], then change to show the
time setting for the operation to occur fi rst.
● The Program Timer will begin operation. (If the On Timer has been
selected to operate fi rst, the unit will stop operating at this point.)
About 5 seconds later, the entire display will reappear.
About Program Timer
● The Program Timer allows you to integrate the Off Timer and the On Timer
operations in a single sequence. The sequence can involve 1 transition from Off
Timer to On Timer, or from On Timer to Off Timer, within a 24 hour period.
The first timer function to operate will be the 1 set nearest to the current time.
●
The order of operation is indicated by the arrow in the remote controller display
([OFF → ON] or [OFF ← ON]).
● An example of the Program Timer use might be to have the air conditioner
automatically stop (Off Timer) after you go to sleep, then start (On Timer)
automatically in the morning before you arise.
[CANCEL] [OFF] [ON]
☞ P. 5).
To Cancel the timer
Use the "TIMER MODE" button to select
[CANCEL].
The air conditioner will return to normal
operation.
To change the timer settings
Perform steps 2 and 3.
To stop air conditioner operation while
the timer is operating
Press the "START/STOP" button.
To change operating conditions
If you wish to change operating conditions
(mode, fan speed, temperature setting, Super
Quiet operation), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
To cancel the timer
Use the "TIMER MODE" button to select
[CANCEL].
The air conditioner will return to normal
operation.
To change the timer settings
1. Follow the instructions given in the section
"To use On Timer or Off Timer" to select the
timer setting you wish to change.
2. Press the "TIMER MODE" button to select
either [OFF → ON] or [OFF ← ON].
To stop air conditioner operation while
the timer is operating
Press the "START/STOP" button.
To change operating conditions
If you wish to change operating conditions
(mode, fan speed, temperature setting, Super
Quiet operation), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
En-8