Page 1
OK Industries Division of Jonard Industries Corp. PTX Series Ergonomic Wire Wrapping Tools - User’s Guide Outils de connexion enroulée ergonomiques - Mode d'emploi Ergonomische Wire-Wrap Geräte - Bedienanleitung Attrezzi ergonomici per Wire Wrapping - Guida per l’utilizzatore B B a a t t t t e e r r y y P P o o w w e e r r e e d d T T o o o o l l E E l l e e c c t t r r i i c c P P o o w w e e r r e e d d T T o o o o l l s s (Model # PTX —...
For more information, please visit our web site at www.okindustries.com. The PTX Series wire wrapping and unwrapping tools have been developed to address ergonomic requirements and boost operator efficiency. With worker safety in mind, we consulted a certified ergonomist and added features including the lightweight, well-balanced construction, a dual-finger short-throw trigger, and a long handle to mitigate pressure on the palm.
BC2 or PTX-BC2-UK); these are sold separately, but can also be purchased with the tool in a kit (see models and descriptions above). All of the tools in the PTX Series have reversible motors, allowing the user to use the tools to unwrap a wire wrapped termination. (NOTE: unwrapping requires a separate bit and sleeve or a dedicated manual unwrapping tool;...
W r r a a p p / / U U n n w w r r a a p p T T o o o o l l The PTX Series power tools require no assembly and are ready for use out of the box.
Page 5
When the battery is charged, remove it from the charger, insert it into the handle of the PTX tool and rotate the end cap of the battery 90 degrees in the counterclockwise direction to engage the cap (see below); then pull back slightly to lock it into the handle of the tool.
Page 6
BIT & SLEEVE INSTALLATION: 1. Loosen collet nut by rotating it in the clockwise direction (see below). Loosen Collet Nut in Clockwise Direction 2. Insert the bit into the chuck, and rotate the bit while pushing it into the chuck, until the bit is seated in the drive mechanism. At this point, the smaller of the two holes in the face of the bit will be at the twelve o’clock position.
Page 7
C C ) ) U U n n w w r r a a p p p p i i n n g g a a n n d d B B a a c c k k f f o o r r c c e e Unwrapping and backforce are special features for wire wrapping, and are available with the PTX Series. All models of the tool, whether battery or electric powered, have the unwrapping feature built in; the backforce feature is optional, and is found in models PTX-1BF, PTX-2BF, PTX-2BF-UK and PTX-48BF.
USING THE BACKFORCE FEATURE: ‘Backforce’ is a feature that compensates for the unnecessary application of downward pressure on the tool during wire wrapping. A wire wrapping tool will perform the wrapping function properly without any downward pressure applied, in fact, such pressure results in a tendency to ‘overwrap’...
Page 9
Bits and Sleeves Chart (AWG) Inches MAXIMUM MINIMUM MAXIMUM TERMINAL TERMINAL REGULAR INSULATION TERMINAL TERMINAL HOLE EFFECTIVE HOLE WIRE MODIFIED SLEEVE DIAMETER DIAGONAL DIAGONAL DEPTH RADIUS DIAMETER GAUGE PART NO. PART NO. INCHES INCHES INCHES INCHES INCHES INCHES • KB18 P194 —...
Each PTX power wrapping and unwrapping tool, as well as the battery chargers, are covered with a six-month warranty from date of purchase. Repair service and technical support are available from OK Industries, Tuckahoe, NY 10707, phone: 914-793-0700, fax: 914-793-4527. Service and repair may be obtained from one of our many worldwide facilities, and technical support can be provided by our representatives and distributors.
P P r r é é s s e e n n t t a a t t i i o o n n g g é é n n é é r r a a l l e e : : L L e e s s O O u u t t i i l l s s P P T T X X d d ' ' O O K K I I n n d d u u s s t t r r i i e e s s OK Industries, le leader mondial des outils de câblage par fil enroulé (wire wrapping), offre une gamme complète d'outils manuels, électriques et sur batterie, de douilles et guide-fil et autres...
Page 13
Choix du produit Référence Description Outil Wrap/Unwrap alimenté sur batterie PTX-1 Outil Wrap/Unwrap 115V PTX-1BF Outil Wrap/Unwrap 115 V avec limiteur de force PTX-2 Outil Wrap/Unwrap 230 V PTX-2BF Outil Wrap/Unwrap 230 V avec limiteur de force PTX-B Batterie pour outil PTX alimenté sur batterie PTX-BC1 Chargeur 115 V pour batteries PTX PTX-BC2...
Page 14
Toujours utiliser des batteries modèle PTX-B, avec le chargeur de batterie PTX-BC1 ou PTX-BC2 tous fabriqués par OK Industries. Ne pas utiliser la batterie avec un cordon ou une prise endommagés, dans un environnement humide ou extérieur, ou à...
Page 15
Quand la batterie est chargée, la retirer du chargeur, l'insérer dans la poignée de l'outil PTX et tourner le capuchon à l'extrémité de la batterie de 90 degrés dans le sens inverse des aiguilles d'une montre pour engager le capuchon (voir ci-dessous), puis le tirer légèrement en arrière pour le verrouiller dans la poignée de l'outil.
Page 16
INSTALLATION DE LA DOUILLE ET DU GUIDE-FIL : 1. Desserrer l'écrou de la bague en le tournant dans le sens inverse des aiguilles d'une montre Desserrer l'écrou de la bague dans le sens des aiguilles d'une montre 2. Insérer le guide-fil dans le mandrin et tourner la douille tout en la poussant dans le mandrin jusqu'à...
Page 17
EFFECTUER UNE CONENXION PAR FIL ENROULE : Etape 1 Etape 1 Choisir la douille et le guide-fil Bit, Sleeve et fil pré- appropriés (voir plus haut). dénudé Etape 2 Etape 2 Insérer le fil dans le trou de fil. Insertion du fil Etape 3 Accrocher le fil.
Page 18
UTILISATION DE LA FONCTION LIMITATION DE FORCE : La limitation de force (Backforce) est une fonction qui compense l'application non nécessaire d'une pression vers le bas sur l'outil pendant l'enroulement du fil. Un outil de connexion enroulée assure correctement l'enroulement du fil sans nécessiter de pression vers le bas, en fait, une telle pression a tendance à...
Page 19
Enrouleurs et Manchons (AWG) mm MAXIMUM MINIMUM MAXIMUM TERMINAL TERMINAL REGULAR INSULATION TERMINAL TERMINAL HOLE EFFECTIVE HOLE WIRE MODIFIED SLEEVE DIAMETER DIAGONAL DIAGONAL DEPTH RADIUS DIAMETER GAUGE PART NO. PART NO. INCHES INCHES INCHES INCHES INCHES INCHES • KB18 P194 —...
Page 20
Pièces détachées pour la série PTX REFERENCE DESCRIPTION REFERENCE DESCRIPTION 21362 Circuit imprimé batterie faible, PTX 21406 Assemblage interrupteur gâchette, outil PTX sur batterie 21328 Moteur, outil PTX sur batterie 20419 Interrupteur gâchette, outils de 16746 Moteur, PTX-1 ou PTX-1BF connexion sur secteur 16772 Moteur, PTX-2 ou PTX-2BF 16771 Moteur, PTX-48 ou PTX-48BF...
Chaque outil de connexion et de déconnexion à fil enroulé PTX, ainsi que les chargeurs de batterie sont garantis six mois à partir de la date d'achat. Un service de réparation et un support technique sont disponibles chez OK Industries ; visitez notre site Web à www.okindustries.com pour contacter un représentant dans votre région.
O O v v e e r r v v i i e e w w : : P P T T X X S S e e r r i i e e s s T T o o o o l l s s f f r r o o m m O O K K I I n n d d u u s s t t r r i i e e s s OK Industries, marktführender Anbieter von Wire-Wrap-Produkten, bietet eine vollständige Palette manueller, elektrisch und batteriebetriebener Geräte,...
Betrieb des Geräts beinträchtigt und zu Geräteschäden führen kann. Benutzen Sie immer die PTX-B Batterien und die PTX-BC1 oder PTX- BC2 Batterieladegeräte, die beide von OK Industries hergestellt werden. Benutzen Sie das Ladegerät nicht, wenn Kabel oder Stecker beschädigt sind, unter feuchten Bedingungen, außerhalb von Gebäuden oder in der Nähe von...
Page 25
Nachdem die Batterie aufgeladen ist, entfernen Sie sie aus dem Ladegerät und setzen Sie sie in den Griff des PTX Geräts ein. Drehen Sie den Batteriedeckel um 90° gegen den Uhrzeigersinn, bis er einrastet (siehe unten); und ziehen Sie ihn dann leicht zurück, so daß er in den Gerätegriff einrastet.
Page 26
Installation von Bit & Muffe: 1. Lösen Sie die Patronenmutter, indem Sie sie im Uhrzeigersinn drehen (siehe unten). Patronenmutter im Uhrzeigersinn lösen 2. Setzen Sie das Bit in das Futter ein. Drehen Sie es, während Sie es gleichzeitig in das Futter drücken, bis es im Antriebsmechanismus sitzt. Das kleinere der beiden Löcher auf der Stirnseite des Bits sollte nun in der 12 Uhr Position (oben) sein.
Page 27
Wire-Wrap-Verbindung herstellen: Schritt 1: Wählen Sie ein geeignetes Schritt 1 Bit und die ensprechende Muffe aus Bit, Muffe und abisolierter Draht (siehe oben). Schritt 2 : Schieben Sie den Draht Schritt 2 in den Drahtschlitz. Einsetzen des Drahts Schritt 3 Verankerung des Drahts Schritt 3 : Verankern Sie den Draht.
Gegendruckfunktion ‘Gegendruck’ ist eine Funktion, mit der überschüssige, nach unten gerichtete Kraft, die auf das Gerät ausgeübt wird, kompensiert wird. Ein Wire-Wrap Gerät führt die Wrap- funktion ordnungsgemäß aus, ohne daß Kraft auf das Gerät ausgeübt werden muß. Tatsächlich führt überschüssige Kraftausübung zu ‘Overwrap’ (weitere Informationen hierzu unter ‚Wire-Wrap-Technologie’).
Jedes PTX Wrap und Unwrap Gerät sowie alle Batterieladegeräte sind mit einer sechsmonatigen Garantie ab Kaufdatum abgedeckt. Reparaturservice und technische Unterstützung sind verfügbar von OK Industries ; Über unsere Website unter www.okindustries.com können Sie einen Repräsentanten in Ihrer Nähe kontaktieren.
Page 32
P P a a n n o o r r a a m m i i c c a a : : A A t t t t r r e e z z z z i i d d e e l l l l a a S S e e r r i i e e P P T T X X d d a a O O K K I I n n d d u u s s t t r r i i e e s s OK Industries, leader a livello mondiale di prodotti per wire wrapping, offre una completa gamma d’attrezzi manuali, elettrici e con alimentazione a batteria, bit...
Page 33
Lista dei prodotti Item Descrizione Attrezzo per Wrap/Unwrap Alimentato a Batteria PTX-1 Attrezzo per Wrap/Unwrap con Alimentazione da Rete 115V PTX-1BF Attrezzo per Wrap/Unwrap con Backforce ed Alimentazione da Rete 115V PTX-2 Attrezzo per Wrap/Unwrap con Alimentazione da Rete 230V PTX-2BF Attrezzo per Wrap/Unwrap con Backforce con Alimentazione da Rete 230V...
Page 34
Usate sempre batterie modello # PTX-B, assieme ai caricabatterie modello # PTX-BC1 oppure PTX-BC2, entrambi prodotti da OK Industries. Non utilizzate il caricabatterie se il cavo di rete o la spina sono dannaggiati, né in ambienti bagnati o umidi, o all’esterno, o in prossimità...
Page 35
Quando la batteria è carica, toglietela dal caricabatterie, inseritela nell’impugnatura dell’attrezzo PTX e girate il cappuccio terminale della batteria di 90 gradi in senso antiorario, per ingaggiare il cappuccio (vedi sotto); tiratela poi leggermente indietro, per bloccarla nell’impugnatura dell’attrezzo. Per togliere la batteria dall’attrezzo, premete nella direzione del Impugnatura cappuccio della batteria, ruotate l...
Page 36
INSTALLAZIONE DI BIT & SLEEVE 1. Allentate il dado del colletto ruotandolo in senso orario Allentate il Dado del Colletto in senso Orario 2. Inserite il bit nella frizione, e ruotate il bit mentre lo spingete nella frizione, fino a quando il bit sia posizionato nel meccanismo di pilotaggio. A questo punto, il più...
Page 37
REALIZZAZIONE D’UNA CONNESSIONE WIRE WRAP Step 1 Step 1 Scegliete il bit e Bit, Sleeve e lo Sleeve adatti (vedi sopra). filo pre-spellato Step 2 Inserite il filo nel Step 2 Inserimento del filo foro per il filo. Step 3 Ancorate il filo.
Page 38
UTILIZZO DELLA PRESTAZIONE BACKFORCE “Backforce” è una prestazione che compensa l’inutile applicazione di pressione sull’attrezzo, durante il wire wrapping. Un attrezzo per wire wrapping eseguirà correttamente la funzione di wrapping senza applicare alcuna pressione in avanti; infatti, tale pressione favorisce la tendenza ad “overwrapping” (fate riferimento alla Sezione intitolata Tecnologia Wire Wrapping per ulteriori dettagli).
Page 39
Tabella dei Bit e Sleeve (AWG) in mm MASSIMO MINIMA MASSIMA PROFONDITA’ DIAMETRO REGOLARE DIAMETRO DIAGONALE DIAGONALE FORO RAGGIO FORO CODICE CODICE ISOLANTE TERMINALE TERMINALE EFFETTIVO EFFETTIVO TERMINALE DIMENSIONE MODIFICATO FILO SLEEVE • KB18 P194 — 1,524 1,854 25,4 3,81 1,905 •...
Page 40
Parti di ricambio per la Serie PTX ITEM PARTE DESCRIZIONE ITEM PARTE DESCRIZIONE 21362 Scheda Batteria Scarica, PTX 21406 Gruppo grilletto, attrezzo a batteria 21328 Motore, attrezzo a batteria PTX 20419 Gruppo grilletto, attrezzi elettrici per 16746 Motore, PTX-1 o PTX-1BF wrapping 16772 Motore, PTX-2 o PTX-2BF 16771 Motore, PTX-48 o PTX-48BF...
Page 41
Ciascun attrezzo elettrico PTX per wrapping ed unwrapping, così come i caricabatterie, sono coperti con una garanzia di sei mesi dalla data dell’acquisto. Il servizio riparazioni ed il supporto tecnico sono disponibili da OK Industries ; Vogliate visitare il nostro sito web www.okindustries.com per contattare un rappresentante nella vostra area.
Page 42
OK Industries Division of Jonard Industries Corp. Tel: (914) 793-0700 134 Marbledale Road Fax: (914) 793-4527 Tuckahoe, NY 10707 www.okindustries.com...