Do you have a question about the A10VO and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Bosch Rexroth A10VO
Page 1
Electric Drives Linear Motion and and Controls Hydraulics Assembly Technologies Pneumatics Service A10VO Variable Displacement Piston Pump Technical Information Manual The Drive & Control Company...
(left hand or right hand) and port locations (rear or side) can be chosen to facilitate your particular installation requirements (ie. direct engine mounting as well as transmission power take off mounting can be accommodated). Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006...
Page 5
Variable displacement swash plate design piston pump. 1. Housing 2. Control Piston 3. Drive Shaft 4. Swash Plate 5. Control Valve Assembly 6. Pistons (x7) Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006 Page 5 of 23...
To protect the system from infinite load pressures, the pressure compensator section of the control will cause the pump to automatically de-stroke when the pre–adjusted maximum system pressure is reached. Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006...
29PSI (abs.) (2 bar). Make sure connection points are airtight and that hoses are sufficiently pressure resistant against external air pressure. Use plastic hoses with supporting mesh. Make sure there are no kinks in the hose when installing. Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006...
Is always defined as viewed on the drive shaft and indicated by a directional arrow. It is not possible to change the direction of rotation of the drive without conversion of the pump. Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca...
250 bar. 5. Screw on the cap nut with external hexagon 17 mm and tighten to a torque of Ma = 8.5Nm. (186 Inch/Lbs.) Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006 Page 10 of 23...
Because of the many pump sizes available we suggest you contact your nearest Bosch Rexroth office for standard leakage rates for your specific pump. Upon receiving this information deadhead a valve function as outlined under Module 2A commissioning instructions.
Suction Port = 1 1/4 SAE Flange Pressure Port = 3/4 SAE Flange Case Drain Port = SAE–8 (3/4–16) Load Sense Port = SAE–4 (7/16–20) Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006 Page 12 of 23...
The hydraulic pump from catastrophic failure should the reservoir oil level become too low. Intended for use on variable displacement piston pumps only. Please refer to Module #9 for more information on this unit. Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca 16/06/2006...
/ 7/8" keyed shaft NOTE: These pumps are also available in many other configurations and sizes. If your needs cannot be met by a pump on this list, please contact your nearest Bosch Rexroth location for assistance. Bosch Rexroth Canada Corp. 3426 Mainway Dr. Burlington, ON L7M 1A8 www.boschrexroth.ca...
Need help?
Do you have a question about the A10VO and is the answer not in the manual?
Questions and answers