Table of Contents
Advertisement
Quick Links
Installation instructions
and user's guide
Equflow 6110 Barcode scanner
Please read this manual carefully before installation and use of the converter.
6110 Barcode scanner
Type: 6110.KC.CON.BC.01
Despite effort to avoid errors in the preparation of this manual, Equflow cannot be held liable for any
mistakes or consequences related to mistakes that may be present.
Copyright: Equflow BV
Version: Manual KC V1.1 EN
Advertisement
Table of Contents
Summary of Contents for Equflow 6110 Series
-
Page 1: Installation Instructions
Please read this manual carefully before installation and use of the converter. 6110 Barcode scanner Type: 6110.KC.CON.BC.01 Despite effort to avoid errors in the preparation of this manual, Equflow cannot be held liable for any mistakes or consequences related to mistakes that may be present. Copyright: Equflow BV... -
Page 2: Table Of Contents
QUICK GUIDE FOR USING THE BARCODE SCANNER ..............7 ............................7 IRST TIME USING ........................7 XCHANGING FLOWMETERS REQUESTING ADDITIONAL BARCODES ................... 8 ..........................8 ARCODE EXAMPLES APPENDIX A – TECHNICAL SPECIFICATIONS ..................9 Equflow BV Manual Equflow 6110 Barcode scanner www.equflow.com Version V1.1 page 2... -
Page 3: Introduction
1.3 General use of the Equflow 6110 Barcode scanner Each Equflow flowmeter has a K-factor, which is the amount of pulses generated when 1 liter of water goes through the flowmeter, with a flow that is within the flowmeter’s flowrange (see the flowmeter’s datasheet/mounting description). -
Page 4: Recommendations For Using Equflow Flowmeters And The Barcode Scanner
At Equflow we calibrate the flowmeters using a steady flow of water. Typically the difference in the K- factor in the Equflow setup and in different process conditions will be constant. So if you notice that for several flowmeters the difference with the Equflow calibration is 5%, than it will likely be the case for all future flowmeters as well. -
Page 5: System Description
2. System description 2.1 General function description The Equflow 6110 barcode scanner converts the K-factor of a flowmeter to a user defined value. This allows exchanging of flowmeters while keeping the output K-factor the same. 2.2 Lay-out description On the front of the barcode scanner the function switch, barcode scanner and LED can be found, see Figure 1. -
Page 6: Installation And Programming Instructions
Function switch has been pressed, the barcode scanner is active After 10 seconds of pressing the function switch and no correct barcode has Red (blinking fast) been scanned. Green (blinking fast) Barcode has been scanned successfully Equflow BV Manual Equflow 6110 Barcode scanner www.equflow.com Version V1.1 page 6... -
Page 7: Quick Guide For Using The Barcode Scanner
Scan the barcode of the new flowmeter Insert the new flowmeter in the system The barcode scanner will now convert the K-factor of the new flowmeter to the user-defined K- factor Equflow BV Manual Equflow 6110 Barcode scanner www.equflow.com Version V1.1 page 7... -
Page 8: Requesting Additional Barcodes
5. Requesting additional barcodes New barcodes for the user defined K-factor or the correction factor can be requested by mailing to info@equflow.com. Make sure to include the new K-factor(s)/percentages for which you would like to receive the barcode. 5.1 Barcode examples ... -
Page 9: Appendix A - Technical Specifications
5 – 30 V square wave (equal to power supply) Output Ambient temp. -10 - +60 C° Dimensions encl. 60 x 56 x 105 mm (L x W x H) Equflow BV Manual Equflow 6110 Barcode scanner www.equflow.com Version V1.1 page 9...
Need help?
Do you have a question about the 6110 Series and is the answer not in the manual?
Questions and answers