Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Magnetrol Solitel
Summary of Contents for Magnetrol Solitel
- Page 1 Installation and Operating Manual Solitel Vibrating Rod evel Switch...
- Page 2 Safety Messages Quality ssurance The Solitel system is rated by the IEC for use in Category The quality assurance system in place at MAGNETROL II, Pollution Degree 2 installations. Follow all standard guarantees the highest level of quality throughout the industry procedures for servicing electrical and computer company.
-
Page 3: Principle Of Operation
Refer to Calibration, Section 2.5. IMPORTANT: Handle the instrument with great care, especially the probe. Any impact on the probe can damage the vibration system. Figure 1 56-601 Solitel Vibrating Rod Level Switch... -
Page 4: Electrostatic Discharge (Esd) Handling Procedure
The SOLITEL switch is mounted to the vessel using a ⁄ " NPT threaded connection. • Ensure that the tip of the probe is located at the desired switching point giving consideration to the slope angle of the material. •... - Page 5 This allows detection of power failure as an alarm status. 7. Wiring is complete. Replace the housing cover. 8. Apply power to the unit. NO CO NC Relay L1(+) No Connection L2/N(-) Power Figure 6 56-601 Solitel Vibrating Rod Level Switch...
- Page 6 NOTE: If the adjustment is too sensitive, the switch may detect even slight residue of material rather than level. Prior to installation, it is recommended that the unit be calibrated using a sample of the media to be measured. 56-601 Solitel Vibrating Rod Level Switch...
-
Page 7: Reference Information
Reference Information Troubleshooting SOLITEL is a simple and reliable device. However, care must be taken to avoid impacting or damaging the vibrat- ing probe. In the event the SOLITEL stops vibrating, the following procedure will identify if the problem is with the electron- ic module or with the sensor: Disconnect the wires going to the sensor. -
Page 8: Replacement Parts
Cover 004-9105-001 Cover o-ring 012-2101-345 Electronics module: ➂ 110 V C Z30-9011-001 24 VDC Z30-9011-004 Bracket 005-6680-001 ➆ ➀ Probe o-ring 012-2408-001 ➄ Snap ring 010-5138-001 ➇ ➅ Sleeve 004-0111-001 Probe Consult Factory ➈ 56-601 Solitel Vibrating Rod Level Switch... -
Page 9: Specification
316 stainless steel Insertion length 8.25 inches (209 mm) 10 to 100 inches (25 to 254 cm) Maximum mechanical load on probe Stranded probe 63 Ft/lbs. (85 Nm) Extended rigid probe 63 Ft/lbs. (85 Nm) 56-601 Solitel Vibrating Rod Level Switch... - Page 10 Conduit connection plugged (38) (38) " NPT " process connection process connection 1.73 (44) Dia. Insertion length Insertion length 1.73 8.25 (44) Dia (209) 6.34 (161) 6.34 (161) Standard Length Extended Rigid Probe 56-601 Solitel Vibrating Rod Level Switch...
- Page 11 Design type code 1 or 2 with probe type code R: Code 000 fixed length of 8.25" (21 cm) Design type code 1 or 2 with probe type code R 10 to 100 inches — Example: 10 inches = code 010 56-601 Solitel Vibrating Rod Level Switch...
- Page 12 Service Policy Return aterial Procedure Owners of Magnetrol controls may request the return of So that we may efficiently process any materials that are a control or any part of a control for complete rebuilding returned, it is essential that a “Return Material or replacement.
Need help?
Do you have a question about the Solitel and is the answer not in the manual?
Questions and answers