Installing Transmitter; Set-Up And Operation; Receiver Set-Up And Operation; Transmitter Set-Up And Operation - LEG LiteSounds Install Manual

Hide thumbs

Table Of Contents

Table of Contents

GREEN AUDIO CABLES

SIDE VIEW

PUSH CABLE

DOWN ON

ALUMINUM

STABS

GREEN CONNECTORS

ALUMINUM STABS

• Use ONLY LiteSounds

UL approved 16 AWG/2C underground low energy,

sunlight resistant, DIRECT BURIAL CABLE (UL E253413) with LiteSounds

FIXTURE CONNECTORS. FIXTURE CONNECTORS each have Max 9 Watts rating

and DIRECT BURIAL CABLE has Max 90 Watts rating.

• Simply place the BLACK CABLE in the groove of the BLACK CONNECTOR

and squeeze the CONNECTOR closed.

• When making the connection of the GREEN SPEAKER CABLE, ensure that

the WHITE STRIPE on the CABLE is properly aligned with the RIB located

on the GREEN CONNECTOR. This is required to ensure proper performance of

the LiteSounds

speaker system.

• Cut off any remaining CABLE maximum of 6" from the last FIXTURE or a

CONNECTOR.

• Ensure that the WHITE STRIPE on the AUDIO CABLE faces the ridge on the

side of the GREEN CONNECTOR used to connect your SPEAKER LIGHTS to

the GREEN AUDIO CABLE.

PLEASE NOTE: IF ALUMINUM STABS BENDS OR ARE BENT, STRAIGHTEN STABS

AND ENSURE A GOOD CONNECTION WITH THE WIRE OR THE LIGHT AND THE

SPEAKER LIGHT WILL NOT WORK.

INSTALLING TRANSMITTER

Find a location for the TRANSMITTER (silver box with 6 inch antenna)

that produces the best sound quality. Test in a few different room

locations in your home, sometimes moving the TRANSMITTER close

to the RECEIVER produces better results.

• Ensure that your TRANSMITTER is plugged into a good working

electrical outlet or that your batteries are well charged if you are

running on the 4-AA batteries.

• Ensure that both the TRANSMITTER and the RECEIVER are set to

the same channel: A >A; B >B; or C >C.

SET-UP AND OPERATION

RECEIVER SET-UP AND OPERATION

• Make sure that TRANSMITTER and the outdoor RECEIVER are

set to the same channel A >A; B >B; or C >C.

FINE TUNE

• FINE TUNE your RECEIVER with the FINE TUNE KNOB to get the best

reception. These are slow small adjustments - FINE TUNE.

Use the volume control to increase volume and listen for clarity. It should

be noted that external factors may cause minor drifting of the FM signal and

require slight adjustment (fine tuning). The FINE TUNING KNOB on the front of the

RECEIVER should be used for this purpose. If distortion is heard, slightly adjust the

TRANSMITTER volume. This will also cause the sound level to increase or decrease

slightly. If you still have distortion, adjust the RECEIVER to compensate as necessary

using the FINE TUNE DIAL.

• Select channel A on the outdoor RECEIVER.

• Plug outdoor RECEIVER into electrical outlet(LED is ON).

• Press the up arrow key on the keypad of the outdoor RECEIVER until sound is

audible from LIGHTED SPEAKER FIXTURES.

• Use the FINE TUNE control on the outdoor RECEIVER for optimal reception.

• Turn lighting control of the outdoor RECEIVER to the ON position.

LITESOUNDS

INSTALL GUIDE

PLEASE CALL US WITH ANY QUESTIONS TO MAKE YOUR INSTALLATION EASIER

AT 1-877-709-3846 OR GO TO OUR WEBSITE: WWW.LITESOUNDS.COM

THE CONNECTOR CLIPS CAN BE

OPENED BY PROGRESSIVELY

SQUEEZING THE LOCKING PINS

TOGETHER (ONE AT A TIME) AND

THEN INSERTING A SCREW

DRIVER IN THE OPENING

CREATED ON THE SIDE.

FINE TUNE

CHANNEL

A B C

*MP3 IS NOT INCLUDED

• Cover PHOTOCELL located on the top of the outdoor RECEIVER to

activate LIGHTS.

TIP 1.

Take advantage of the FM RECEIVER if there is a local radio station that you like

in the 106.9 MHZ - 107.7 MHZ. With your TRANSMITTER off, you can use your

FINE TUNE KNOB on your RECEIVER to tune in the local radio station you enjoy.

VOLUME

TIP 2.

LITESOUNDS

MUSIC SYSTEM

DOWN

00:01

00:02

LIGHTS

You can plug your portable audio device directly into your RECEIVER

POWER

ON OFF

AUDIO INPUT

when you are outdoors. Use a 3.5mm male straight.

TIP 3.

You can run multiple LiteSounds

TRANSMITTER. This will allow you to increase the coverage area of your outdoor

audio and your outdoor lighting. For example you could have 2 outdoor RECEIVERS

with up to 10 fixtures on each RECEIVER (4 SPEAKER LIGHTS and 6 LIGHT

FIXTURES) for a total of 20 FIXTURES outside. So if you placed 3 LiteSounds

RECEIVER outdoors, you could have 30 FIXTURES, etc.

TIP 4.

You can have multiple audio sources in multiple locations. For Example, you can

place 1 LiteSounds

system in front of your home to greet guest. With the

TRANSMITTER on Channel A, use a unique AUDIO SOURCE (MP3-1 for Example).

Simultaneously, you can have a second LiteSounds

home using a second AUDIO SOURCE (MP3-2 for Example) playing different music.

This will require two LiteSounds

KITS (2 TRANSMITTERS, 2 RECEIVERS).

WHEN YOU HAVE CONCLUDED LISTENING TO YOUR LITESOUNDS SYSTEM,

PLEASE REMEMBER TO TURN THE VOLUME DOWN ON YOUR RECEIVER.

TRANSMITTER SET- UP AND OPERATION

Tune the TRANSMITTER by selecting the optimum channel (see chart

below) and increasing the output volume on the side of the unit to

maximum output.

TABLE 1

Channel

FM Frequency

Fine Tune - Low Range

107.3 MHZ

106.9 MHZ

107.5 MHZ

107.1 MHZ

107.7 MHZ

107.5 MHZ

• Plug in TRANSMITTER to power supply or install batteries(4AA).

• Connect TRANSMITTER to AUDIO SOURCE.

• When connecting the AUDIO SOURCE to the TRANSMITTER, use the

'Headphone' Jack on your device for input to the LiteSounds

and position volume control at or near maximum.

• You can also use AUDIO output connectors.

• Place ANTENNA in upright position.

• Select channel "A" on TRANSMITTER (Make sure that TRANSMITTER and the

outdoor RECEIVER are set to the same channel A >A; B >B; or C >C).

• Turn TRANSMITTER power to ON (LED will be ON-The Red LED will glow

indicating operation).

• Adjust DIAL VOLUME CONTROL to at or near maximum level.

• Turn ON audio source and/or press play.

• Adjust VOLUME CONTROL DIAL on front of the TRANSMITTER to maximize

sound clarity/volume.

• Once you have FINE TUNED your RECEIVER, you can use the volume on the

front of the TRANSMITTER to improve the clarity and the volume of your

signal. Correct and optimum placement of TRANSMITTER and RECEIVER

equipment varies site-to-site due to numerous extraneous factors that

cannot be controlled.

PLEASE NOTE: THE TRANSMITTER FEATURES A VOLUME CONTROL ON THE

FRONT PANEL. USE THIS CONTROL TO ADJUST THE INPUT VOLUME OF THE

AUDIO SOURCE IF DISTORTION IS AUDIBLE IN THE SPEAKERS.

PLEASE NOTE: WHEN USING THE TRANSMITTER WITH 9V DC POWER SUPPLY,

IT IS NOT NECESSARY TO TURN OFF THE TRANSMITTER.

RECEIVERS from one LiteSound

®*

system playing out back of your

Fine Tune - High Range

107.5 MHZ

107.7 MHZ

107.9 MHZ

TRANSMITTER

Table of Contents