Phenix VMS-1 Manual

Portable

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

PORTABLE POWER SUPPLY

MODEL NUMBER VMS-1

VERSION 1.0

September 21, 2012

Table of Contents

Need help?

Do you have a question about the VMS-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Phenix VMS-1

Page 1 PORTABLE POWER SUPPLY MODEL NUMBER VMS-1 VERSION 1.0 September 21, 2012...
Page 2: Table Of Contents
TABLE OF CONTENTS Section Number DANGER INTRODUCTION AND TECHNICAL SPECIFICATIONS CONTROL AND METERING DESCRIPTION OPERATION AND CALIBRATION CIRCUIT DIAGRAM SYMBOLS ELECTRICAL DRAWINGS PARTS LIST RECOMMENDED SPARE PARTS PARTS ORDERING INFORMATION RETURNED MATERIAL...
Page 3: General Safety Precautions
 DO NOT operate damaged equipment. Remove power, and do not use the equipment until safe operation can be verified by service-trained personnel. Phenix Technologies, Inc. assumes no liability for unsafe or improper use of test equipment.
Page 4 INTRODUCTION The Phenix Technologies VMS-1 Portable Power Supply is well equipped with the various features listed on the specifications page to allow for the easy testing of the operational voltage/current of electro-mechanical devices. The VMS-1 allows the user to carefully dial in an output voltage or current to determine the operational voltage or current levels needed for the “switching state”...
Page 5: Technical Specifications
TECHNICAL SPECIFICATIONS Model: VMS-1 Portable Power Supply Input: 120 Volts, 10 Amps, 60 Hz, Single Phase Output: 0-120VAC; 10AAC MAX through binding posts. Instrumentation: Digital Voltmeter, 3 ½ digit resolution Scale: 0-199.9VAC. Accuracy:  0.4% FS  2 counts Digital Ammeter, 3 ½ digit resolution Scale: 0-19.99AAC.
Page 6: Control And Metering Description
CONTROL AND METERING DESCRIPTION (Key numbers refer to Figure 1) Main Power In. Main Power Circuit Breaker. Serves dual function as main switch and provides overload protection for all circuits in test set. Main Power Indicator Lamp. Lights when main power circuit breaker is energized and in the ON position.
Page 8: Operation And Calibration
OPERATION AND CALIBRATION OPERATION Setup Open unit and connect input power supply cord to the power inlet and a standard wall outlet. Ensure Coarse and Fine adjustment knobs are dialed to their zeroed out positions before connecting output terminals. If either of the two Overload circuit breakers are tripped, press the push button to reset the breakers.
Page 9 The onboard digital Voltmeter and Ammeter will also hold its normally calibrated settings during the lifetime of your VMS-1 for all normal indoor operations. In the rare case that either meter needs calibration adjustments, the procedure for doing so should be performed by qualified technical personnel such as the Phenix Technologies Service Department during a scheduled service appointment.
Page 11: Electrical Diagrams
ELECTRICAL DIAGRAMS Drawing Number Description 9907000 VMS-1 Electrical Schematic...
Page 12: Parts List
VMS-1 PARTS LIST PHENIX QTY. ITEM # PART # DESCRIPTION 2100479 Portable Power Supply Case with Carry Handle CON1 1153328 Screw MNT Power Inlet Receptacle F1-2 1603601 AGC-1 Fuse F1-2 1603910 Single Pole Fuse Holder for AGC type Fuse 1601310...
Page 13: Recommended Spare Parts
RECOMMENDED SPARE PARTS PHENIX QTY. ITEM # PART # DESCRIPTION F1-2 1603601 AGC-1 Fuse 1423270 Neon Lamp Yellow 1077164 Power Cord 16/3 10FT 1506511 Digital AC Voltmeter 1506512 Digital AC Current meter Output lead wires 1353205 Banana Plug Black 1356200 Banana Plug Red Gator Clip –...
Page 14: Parts Ordering Information
When your purchase order is received at our office, a representative of Phenix Technologies will contact you to confirm the current price of the part being ordered. If a part you order has been replaced with a new or improved part, an Applications Engineer will contact you concerning any change in part number.
Page 15: Returned Material
Serial Number Reason for Return Cause of Defect If Phenix Technologies, Inc. deems return of the part appropriate, it will then issue an "Authorization for Return". If return is not deemed advisable, other inspection arrangements will be made. NOTE: Material received at this plant without the proper authorization shall be held as "Customer's Property"...