Download
Share
Print this page
JETWAKE B200 User Manual
  1. Manuals
  2. Brands
  3. JETWAKE Manuals
  4. Accessories
  5. B200
  6. User manual

JETWAKE B200 User Manual

Electric surfboard
Hide thumbs

Advertisement

Quick Links

Download this manual
Electric Surfboard

(USER MANUAL)

VERSION 19-JW001
Copyright 2019, All rights reserved
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
PLEASE KEEP THIS MANUAL AT A SAFE PLACE AND HAND IT OVER TO A NEW OWNER IF YOU SELL THE VESSEL.

Advertisement

loading

Summary of Contents for JETWAKE B200

  • Page 1: User Manual

    Electric Surfboard (USER MANUAL) VERSION 19-JW001 Copyright 2019, All rights reserved CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. PLEASE KEEP THIS MANUAL AT A SAFE PLACE AND HAND IT OVER TO A NEW OWNER IF YOU SELL THE VESSEL.
  • Page 2 User's Guide Copyright 2019, All rights reserved In addition to our passion for technology, the JETWAKE ™ team constantly pursues perfection to ensure that all products are new and fun. "Pleasure for users", this is our vision. We are not afraid to try new ideas and overcome the limitations in order to experience the greatest joy.
  • Page 3 INTRODUCTION This manual will help you to operate the JETWAKE ™ electric surfboard 'B200' safely and easily. The B200 provides information on the name of each part, its description, precautions, how to use it, system and operation, maintenance, and maintenance.
  • Page 4 Electric Surfboard Model : B200 Size : 1800 x 700 x 130 mm Weight : Board 15 kg/Controller10 kg/Battery 20kg Run time: 30~45 min Operating temperature : 5~35℃ Storage temperature : 0~40℃ Speed: 25~40 km/h * Test rider : height 184cm, weight 80kg -> speed 30kmh * Test rider : height 170cm, weight 64kg ->...

  • Page 5: Wireless Controller

    Wireless Controller Model : B200-C1-AB Size : 118 x 67 x 22 mm Weight :122g Operating temperature : 5~35℃ Storage temperature : 0~40℃...
  • Page 6 B200 SET Board 1 PC Propellent 1 PC Battery Pack 1 PC 1 PC Wireless Controller 1 PC Power Charger Magnet Switch (with leash) 1 PC...
  • Page 7 1. Board 1-1. Board body 1-2. Battery Room 1-3. Fasteners – Locking Receptacle 1-4. Drain Plug 1-5. Foot strap1 1-6. Foot strap2...
  • Page 8 2. Controller 2-1. Jet Nozzle 2-2. Guide Vane 2-3. Jet Tunnel 2-4. BLDC Motor 2-5. Main Controller 2-6. Connector (+) 2-7. Liquid Tight Threaded Vent Plug...

  • Page 9: Battery Pack

    3. Battery Pack 3-1. Battery body 3-2. Magnet Switch Holder 3-3. Liquid Tight Threaded Vent Plug 3-4. LED 3-5. Tray handle 3-6. Fasteners – Stud 3-7. Connector (-) 3-8. Connector Waterproof Seal...
  • Page 10 4. Wireless Controller 4-1. Wireless Controller body 4-2. Power 4-3. Trigger 4-4. Power Lamp Window 4-5.

  • Page 11: Power Charger

    5. Power Charger 5-1. Power Charger Body 5-2. Switch 5-3. 5-4. Cooler 5-5. Connector (+) 5-6. 110V / 220V Plug...
  • Page 12 - Do not disconnect or connect the Power Pack when the B200 is near water or water. - Do not use B200 in the presence of floating debris because there is a risk of B200 or user injury. - After using the B200, remove the Power Pack.
  • Page 13 - Do not use it for safety in a swimmer or a diver! - Do not store the product in direct sunlight or in an enclosed vehicle! - The B200 can not be used as a swimming aid! - The B200 incorporates mechanical, electrical and software safety systems.
  • Page 14 - Always remove the Power Pack from the B200 when storing the product! - When transporting the B200, always remove the power pack and install it only when it is used! - Always disconnect the power pack from the charger and turn it off when not charging! - When disconnecting the power pack from the charger, first turn off the charger! - Do not disconnect or connect the Power Pack when it is near water or liquid.

  • Page 15: How To Charge The Battery Pack

    How to charge the battery pack Red: waiting for charging Orange: charging - Please observe the charging sequence of the charger. Green: Charging complete Battery pack (bottom connector) Plug the power plug into a 220V outlet. Check power switch 'OFF' position Connecting the charge connector * 110V specification is requested separately * Red: Charging standby...
  • Page 16 How to use the wireless controller Wireless connection (LED steady) Press the power lever once. No wireless connection (LED blinking) * Magnetic power switch on board Green or Red Green : Available Red : Requires charging Check the battery level of Check the board battery level Use lever to adjust speed the wireless controller...
  • Page 17 Green : Available Charging the wireless controller Red : Requires charging Standby Charging (Blue LED steady) Press the power lever once. * Magnetic power switch on board (Green or Red Flashed) Green or Red Flashed Standby Blue Fixed Charging in progress Wireless charger operates Blue Flashed inappropriately...
  • Page 18 3 Setting the speed of the wireless controller - Since the level setting is one time, set the level when using it. - Set the level before riding the B200 and use it. After adjusting the power, While holding down the power lever Press the trigger to adjust the step.
  • Page 19 Replacement of the main control PCB  ① Please remove the cover of main ② Please seperate the bolts(M5) which Using the hex keys wrenches in a control using the hex keys wrenches are connected with red line(+) and counterclockwise direction , separate in a counterclockwise direction .
  • Page 20 Replacement of the coupling  ① Please remove the vent-plug using a ② Please remove the setscrew(M4) ③ Please remove the bolts(M8) which is spanner. which is clamped with the coupling clamped with BLDC Motor and Jet using the hex keys wrenches in a Tunnel using the hex keys wrenches in a counterclockwise direction.
  • Page 21 bushing and impeller Replacement of the  ① Please follow the replacement of the ② Please pull out the Jet nozzle and ③ Please pull out a shaft and impeller coupling ① to ④, remove the guide vane in a horizontal direction from the Jet tunnal in a horizontal bolts(M6) which is clamped with Jet direction by hands.
  • Page 22 Replacement of the Bearing module  Please follow the replacement of ② Using the box wrench(M20), remove ③ Please replace new ones and than  the coupling ① to ④, and than the bearing module. for assembling new one, do it in follow replacement of the bushing reverse order and impeller ①...
  • Page 23 The separation of the battery pack  ① To unlock them, please turn 4 ② Please hold the two handles by ③ To seperate battery pack from the Fasteners at 180 degrees in a hands. board, softly lift up it. counterclockwise direction.
  • Page 24 Magnet switch and Leash  ① Please properly fasten the leash to ② Please put magnet switch on the ③ Please check the light of magnet axis of the back of the ankle. magnet switch holder. switch holder. Replacement of the magnet switch and leash ...
  • Page 25 Clean  Please sprinkle freshwater on the board without the separation of battery pack. Caution> Please do not wash with the separation of battery Caution> If your board meet the salt water, it`s going to cause corrosion. pack. So please after using board, you should clean yours in freshwater.
  • Page 26 FCC Compliance information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.