Subscribe to Our Youtube Channel
Summary of Contents for SawStop T-Glide Industrial II Series
- Page 1 SawStop ® T-Glide Fence System- ™ Industrial Series II OWNER’S MANUAL TGI2-FRT36A TGI2-FRT52A...
-
Page 2: Warranty
This warranty is void if the fence system or any portion of the fence system is modified without the prior written permission of SawStop, LLC, or if the fence system is located or has been used outside of the country where the authorized SawStop distributor from whom the fence system was purchased resides. - Page 3 Leg Support Bracket (2) Support Leg (2) 5 mm Hex Key 5 mm Ball-End Hardware Bag Owner’s Manual Hex Driver Leveling Foot (2) Fig. 1 Page 3 SawStop T-Glide Fence System - Industrial Series II...
-
Page 4: Installation
Use a 5 mm hex key and a 13 mm wrench to tighten the nuts, to secure the wings in place. Fig. 3 Page 4 SawStop T-Glide Fence System - Industrial Series II... - Page 5 M8 washer (14), an M8 lock washer and an M8 hex nut (16). Hand-tighten the nuts. Once mounted, the brackets should create a shelf for the table to rest on (Fig. 6). Fig. 6 Fig. 5 Page 5 SawStop T-Glide Fence System - Industrial Series II...
- Page 6 With the weight of the extension table still supported, turn the adjustment screw with a 5 mm hex key until the extension table is level and flush with the extension wing. Page 6 SawStop T-Glide Fence System - Industrial Series II...
- Page 7 Place an M8 washer (14), an M8 lock washer (15) and an M8 hex nut (16) on the threaded end of each bolt. Hand- tighten the nuts; do not fully tighten them. Do not insert bolts through the outermost holes in the front and rear rails at this time. Page 7 SawStop T-Glide Fence System - Industrial Series II...
- Page 8 (24), and an M10 lock nut (25) (Fig. 16), and then fully tighten the bolts using two 17 mm wrenches. NOTE: The leg support brackets align with different holes in the front and rear legs because the brackets are at different heights. Rear Front Rail Rail Fig. 16 Page 8 SawStop T-Glide Fence System - Industrial Series II...
- Page 9 Insert M8 x 40 countersunk socket head bolts (17) through the three remaining rear rail holes and into the corresponding holes in the front edge of the extension table. Place an M8 washer (14) and an M8 lock nut (16) on each bolt and hand-tighten. Fig. 18 Page 9 SawStop T-Glide Fence System - Industrial Series II...
- Page 10 (Fig. 23) and hand-tighten. Note: the hardware bag includes enough hardware to mount the 52” tube. If you have a 36” assembly, disregard the extra hardware. Fig. 23 Page 10 SawStop T-Glide Fence System - Industrial Series II...
- Page 11 Next, attach the fence handle to the fence by threading the handle into the cam lock (Fig. 25). Press down on the fence handle to clamp the fence to the main tube (Fig. 26). Fig. 25 Fig. 26 Page 11 SawStop T-Glide Fence System - Industrial Series II...
- Page 12 Once both ends of the tube are adjusted correctly, tighten the remaining M8 x 16 hex head bolts to lock the tube to the front rail. The fence should now slide smoothly along the tube without binding and without excessive play when changing directions. Page 12 SawStop T-Glide Fence System - Industrial Series II...
-
Page 13: Fence Adjustments
10 Phillips head screws (13) shown in Fig. 31 and slide the indicator lens to the right or left until the cursor is directly over the correct measurement. Tighten the screws to lock the position of the indicator lens. adjust the indicator lens by loosening the two Phillips screws Fig. 31 Page 13 SawStop T-Glide Fence System - Industrial Series II... - Page 14 The next step is to adjust the face plates (2) to be perpendicular to the table top. The angle between the face plates and the table is set by the two plastic leveling screws (9) on top of the glide bracket (Fig. 33). Fig. 33 Page 14 SawStop T-Glide Fence System - Industrial Series II...
- Page 15 The heads of the screws fit into key-hole slots in the sides of the fence (Fig. 35). Fig. 35 Page 15 SawStop T-Glide Fence System - Industrial Series II...
- Page 16 Lift the fence off the tube and set it on the table with the left face plate down, making sure the position of the face plate doesn’t move. Tighten the screws to lock the left face plate onto the fence. Your fence is now fully adjusted and ready to use. Fig. 37 Page 16 SawStop T-Glide Fence System - Industrial Series II...
- Page 17 Once the fence is in the correct position, push the red locking handle down to the locked position (Fig. 38). The fence is now locked in place and ready for use. Fig. 38 Page 17 SawStop T-Glide Fence System - Industrial Series II...
- Page 18 Page 18 SawStop T-Glide Fence System - Industrial Series II...
-
Page 19: Fence Assembly
Hardware Bag for Rail Assembly (items 2-7) TGI2-020 5mm Ball-end Hex Driver TGI2-021 6mm Hex Wrench TGI2-022 Fence Installation Guide TGI2-023 Fence Attention Magnet TGI2-024 *Each Fence box also contains the hardware for the Rail Assembly. Page 19 SawStop T-Glide Fence System - Industrial Series II... - Page 20 Page 20 SawStop T-Glide Fence System - Industrial Series II...
- Page 21 32) *Each Fence box contains one bag of hardware for a 52” Rail Assembly. If you purchased a 36” Rail Assembly, you can disregard the extra hardware. Page 21 SawStop T-Glide Fence System - Industrial Series II...
- Page 22 Page 22 SawStop T-Glide Fence System - Industrial Series II...
- Page 23 Hardware Bag for 52 inch Extension Table Assembly for TGI2 TGI2-065 (items 14-17, 21-25, 28-34) Supplemental Mounting Kit (for TGI2 tables with older date TGI2-WA-001 codes that do not use item 32) Page 23 SawStop T-Glide Fence System - Industrial Series II...
- Page 24 Fax - (503) 570-3303 Email: info@sawstop.com Updates of this manual may be available at www.sawstop.com. Copyright SawStop, LLC. All Rights Reserved. SawStop is a registered trademark and T-Glide is a trademark of SawStop, LLC. March 2019 M ICS 19 0001 00...
Need help?
Do you have a question about the T-Glide Industrial II Series and is the answer not in the manual?
Questions and answers