Do you have a question about the XAG-500 and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for XU1 XAG-500
Page 1
G r i n d e r 1 0 0 m m A n g l e 5 0 0 W XAG-500 Operating Instructions XU1 Power tools 1–23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 XAG-500 0717...
Page 3
5. Do not use any kind of attachment (discs or 3. Make sure you are well balanced when using the attachment fitment instructions. XU1 tools will not be otherwise) that has a diameter greater than 100mm) tool and you have secure footing. Do not use the tool responsible for any damage or injury caused due to the 6.
Page 4
Note: XU1 Tools will not be responsible for any damage or injuries caused by repair of the Angle Grinder by an unauthorised person or by mishandling...
Page 5
SAFETY c) Prevent unintentional starting. Ensure the Caring for the environment switch is in the off-position before connecting to power source and/or battery pack, picking up INSTRUCTIONS Power tools that are no longer usable should or carrying the tool. Carrying power tools with your not be disposed of with household waste but in finger on the switch or energising power tools that an environmentally friendly way.
Page 6
m) Do not run the power tool while carrying it e) Always use undamaged wheel flanges that are 5) Service at your side. Accidental contact with the spinning of correct size and shape for your selected wheel. accessory could snag your clothing, pulling the a) Have your power tool serviced by a qualified Proper wheel flanges support the wheel thus reducing accessory into your body.
Page 7
H a m m e r D r i l l 5 0 0 W XHD-500 Operating Instructions XU1 Power tools 1–23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 XHD-500 0717...
Page 8
1 Metal Chuck 5 Forward / Reverse Lever 2 Side Handle 6 Lock-On Button 3 Drill / Hammer Selector 7 Variable Speed Trigger 4 Depth Rod 8 Power Cord Drilling Depth Drill Hammer...
Page 9
2. Use the chuck key to loosen the chuck 3. Once the lock-on button has been engaged the Your XU1 Hammer Drill has been designed for drilling switch will remain locked on. 3. Remove the bit timber and metal utilising a normal drilling action and 4.
Page 10
WARRANTY Drilling in wood 1. Move the mode selector to the right (drill bit icon) to YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A select the drill mode. CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS 2.
Page 11
SAFETY When operating a power tool Caring for the environment outdoors, use an extension cord INSTRUCTIONS Power tools that are no longer usable suitable for outdoor use. Use of a cord should not be disposed of with household suitable for outdoor use reduces the risk of waste but in an environmentally friendly electric shock.
Page 12
Do not use the power tool if the ADDITIONAL SAFETY switch does not turn it on and off. Any power tool that cannot be controlled INSTRUCTIONS FOR with the switch is dangerous and must be HAMMER DRILLS repaired. Disconnect the plug from the power The tool is recommended for use with a residual source and/or the battery pack from current device with a rated residual current of 30mA...
Page 13
XU1 Power tools 1–23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 XOS-401 0618...
Page 14
1 Palm Grip 5 Adaptor 2 On/Off Trigger 6 Base Plate 3 Lock-On Button 7 Front Clamp Lever 4 Dust Extraction Chute...
SPECIFICATIONS OPERATION 3. Place the sandpaper on the Base Plate ensuring that the holes in the sandpaper line up with those in the Base Plate. 135W Motor: WARNING! Guide the cord during sanding 4. Insert the front edge of the sandpaper into the front Input: 230-240V ~ 50Hz to prevent it being caught on the workpiece, or...
Page 16
Take the sander to a suitably qualified electrician or power tool repairer for replacement. Always replace both brushes at the same time. Note: XU1 will not be responsible for any damage Australia/New Zealand (Head Office) or injuries caused by the repair of a tool by an 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175 unauthorised person or by mishandling of the tool.
Page 17
SAFETY battery pack, picking up or carrying the General Power Tool Safety tool. Carrying power tools with your finger on the Warnings INSTRUCTIONS switch or energising power tools that have the switch on invites accidents. WARNING! Read all safety d) Remove any adjusting key or wrench ALWAYS WEAR EYE, FACE AND warnings and all instructions.
Page 18
ADDITIONAL SAFETY generated by your operation. Prolonged movement at the point of snagging. d) Use special care when working corners, exposure to high intensity noise may INSTRUCTIONS FOR cause hearing loss. sharp edges etc. Avoid bouncing and SANDERS i) Keep bystanders a safe distance away snagging the accessory.
Need help?
Do you have a question about the XAG-500 and is the answer not in the manual?
Questions and answers