Advertisement
BASICS
Thank you for purchasing the KIC6210 Digital
Lock. Your new KIC6210 Digital Lock advanced
features include:
•
1 Master Code for entry including all other
functions.
•
1 Sub-Master Code for entry and other
programming functions.
•
10 Manager Codes for entry and other
programming functions.
•
90 User Access Codes for entry.
•
5 Service Codes (One-Time Entry Code).
•
2 Remote Switch Input.
•
2 User Disable Modes.
- Disable all user codes except Master Code.
- Group disable all user codes except Manager
Codes.
•
Keypad Anti-Tamper Lockout (30 seconds).
Keypad is disabled
after 3 unsuccessful user code entries.
•
Fire Alarm System (REM2)
INITIAL SETUP
1. Remove batteries or disconnect any power
source. Press and hold (#) for 10 seconds
and release.
2. Within 3 seconds after placing the batteries,
press the (#) button 3 times. The BLUE LED light
continuously light for 3 seconds and 2 beeps
will be heard.
3. The unit is now clear of all programmed data
and will have reverted to the factory default
Master Code 12345.
NOTE: Please follow procedures above exactly
otherwise unit will function abnormally. In this
case, please repeat the procedure. No other
programming commands will be accepted
until default Master Code has been changed.
2
CODES
Codes may be 3, 4 or 5 digits long. The length of
the Master Code determines all the codes format.
Once the numbers of digits are selected, it cannot
be changes unless all programming is erased and
the default factory settings are reloaded.
No other programming commands will be accepted
until default Master Code has been changed.
MASTER CODE & SUB-MASTER CODE
•
This unit is delivered with the Master Code set
to 12345 (default).
•
The Master Code cannot be deleted.
•
Master Code performs all programming functions.
•
Sub-Master Code performs all programming
functions except delete or change Master code.
MANAGERS CODE
•
All Managers Code location ends in zero.
(00, 10, 20, 30, 40, 50, 60, 70, 80, 90)
•
Manager Codes are capable of programming and
deleting user codes under his Group Managers
are also capable of accessing the next higher
Group until another Manager Code appears.
USER CODES
•
Does not have programming privileges.
Codes are used for entry only.
SERVICE CODES
•
Service Codes are one-time codes only. It cannot be
used again. Once a service code is entered, the unit
will unlock but it will automatically delete the code.
VALID CODES & PASS TIME (DOOR UNLOCK)
•
Pass Time is the time the unit is unlocked after a
valid code is entered.
•
BLUE LED will flash (with 2 beeps) after a valid
code is entered.
•
Pass Time also determines the amount of time
between two key presses. If the succeeding entry
(or key press) was pressed after the Pass Time,
it is now considered as a new entry. Should this
happen, wait 5 seconds for the unit to reset by
itself then try entering the code again.
INVALID CODES
•
The RED LED will flash for 5 seconds with one
beep after an invalid code is entered.
PROGRAM REFERENCE GUIDE
QUICK
PROG
PROGRAM
FUNCTIONS
NO.
FINDER
Unlock (Entry Only)
Unlock and Enter
Programming Mode
A
000
Next Free Code Access
Locator
B
009
Code Location Function
C
011-015
Add Service Codes
D
021-025 Delete Service Code
E
02#
Delete All Service Codes
F
1xx
Add/Change Manager Code
or User Codes
G
2xx
Deleting Manager or User
Codes
H
3xx
Disable 1 Manager or User
Code
I
3x#
Disable User Codes in 1 Group
J
3##
Disable All
K
4xx
Enable 1 Manager or User
Code
L
4x#
Enable User Codes in 1 Group
M
4##
Enable All
N
902
Pass Time (Door Unlock)
O
93#
Disable Users Only
P
961
Enable Passage Mode
Q
962
Disable Passage Mode
R
971
Key press Sound option:
Normal
S
971
Key press Sound + LED
(Default)
T
972
Key press Sound Option: Click!
U
972
Key press Sound + LED
V
973
Key press sound Option: LED
Only
W
981
Add/Change Sub-Master Code
X
982
Delete Sub-Master Code
Y
991
Change Master Code
SUB-
GROUP
MASTER
USER
SERVICE
MASTER
MANAGER
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
3
Advertisement
