The TAB (tape-automated bonding) leads between the electronics and the display glass are very sensitive to handling. When cleaning the edges of the display glass, special care should be taken not to damage the leads. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530...
There is no overcurrent protection on V input to protect against catastrophic faults. Beneq recommends the use of a series fuse on the 12 volt supply. A general guideline is to rate the fuse at 1.8 to 2 times the display maximum current rating...
Samtec. Consult your Samtec representative for the cable/connector options. Compatibility with non-Samtec equivalents should be verified before use. Figure 2. Samtec EHF-113-01-L-D-SM connector Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372...
0 bit 1 Bit 0 Note: NIU = Not In Use Table 7. LVDS single bus, 24 bpp, JEIDA data packing. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372 FI-02200 Espoo Fax +358 9 7599 5310 www.beneq.com...
Figure 3. Video input data timing diagram, 18 bpp, VESA data packing Figure 4. Video input data timing diagram, 18 bpp, JEIDA data packing Figure 5. Video input data timing diagram, 24 bpp, VESA data packing Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530...
Vertical data width Vertical porch width Set-up time DATA Hold time Rise/fall time Figure 8. LVDS receiver timing chart. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372 FI-02200 Espoo Fax +358 9 7599 5310 www.beneq.com Finland lumineq@beneq.com...
See color settings table Blue scale 1 See color settings table Normal operation Self-test 1 Normal operation Self-test 2 Default: All OFF Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372 FI-02200 Espoo Fax +358 9 7599 5310 www.beneq.com Finland lumineq@beneq.com...
Blue value 1/8 Self-test The display incorporates two self-test modes. The self-test mode is selected by the dip switch. See figure 6, dip switch and table 9, dip switch settings. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372...
Analog dimming control circuitry is present on this display model. This feature allows manual analog dimming of the brightness from 100 % to approximately 5 % (dark) of the full brightness. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530...
D/A converter may be used to facilitate dimming by sinking a maximum of 100 µA (for maximum dimming) from pin 1 to pin 2 of the dimming connector. See the figures 7 and 8 for typical analog dimming performance. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530...
Page 16
Operation Manual EL640.480-AM LVDS Figure 11. Analog dimming adjustment Figure 12. External voltage dimming Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372 FI-02200 Espoo Fax +358 9 7599 5310 www.beneq.com Finland lumineq@beneq.com www.lumineq.com Date: February 7, 2017 Document number: ED001137 Rev.
Fill factor 57 % Pixel pitch 0.33 x 0.33 (W x H) Pixel size 0.25 x 0.25 (W x H) Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372 FI-02200 Espoo Fax +358 9 7599 5310 www.beneq.com Finland lumineq@beneq.com...
Figure 5 illustrates the distance the components extend behind the display. Tall components do not necessarily fill this area. Beneq reserves the right to relocate components within the constraints of the component’s envelope without prior customer notification. For this reason, Beneq advises users to design enclosure components to be outside the component envelope.
SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Beneq Oy Olarinluoma 9 Tel. +358 9 7599 530 VAT ID FI19563372...
This document is compiled and kept up-to-date as conscientiously as possible. Beneq cannot, however, guarantee that the data are free of errors, accurate or complete and, therefore, assumes no liability for loss or damage of any kind incurred directly or indirectly through the use of this document. The information in this document is subject to change without notice.
Need help?
Do you have a question about the Lumineq EL640.480-AM LVDS and is the answer not in the manual?
Questions and answers