Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for imovr TermoTread GT
- Page 1 Office Walking Treadmill by iMovR OWNER’S MANUAL...
-
Page 2: Table Of Contents
Keep in mind that the user’s primary goal should be to spend less time sitting - while gaining some benefits from working with a slightly elevated heart rate. Cardio exercise is decidedly not the objective of treadmill desking. As we like to say at iMovR, “if you’re sweating, you must be doing it wrong!”... -
Page 3: Important Safety And Operation Instructions
GETTING STARTED The Ready-Set-Go section of this manual will get you upright and walking in no time, but first we need to review some important safety information to ensure that your experience is a positive one and that your equipment always performs at peak efficiency. The vast majority of treadmill support calls can be attributed to a failure to properly level the treadmill or to keep it properly lubricated and clean. - Page 4 • The ThermoTread GT is designed as a walking treadmill that the treadmill on an anti-static treadmill mat (contact iMovR will allow the user to perform basic work functions (reading, to purchase). If you experience static shocks when touching...
- Page 5 • If you find that your treadmill is tripping a circuit breaker then immediately stop using the treadmill and make sure it is properly cleaned, and lubricated with iMovR-brand, 100% silicone lubricant. If there is a lot of dirt under the belt follow the instructions in this manual for Cleaning The Tread-Belt.
-
Page 6: Console Operation
CONSOLE / SCREEN DISPLAY & OPERATION GET READY >>>>> READY 1. GETTING READY INITIAL SCREEN DISPLAY Once the connections are made and the power switch is turned on the console will display this screen asking you to either select an existing User Profile or create a new one. Press CREATE USER then USER 1 will display. -
Page 7: Get Set - Setting Your Profile, & Mode Selection
GET SET >>>>> SETTINGS 2. SETTING YOUR PROFILE MODE SELECT SCREEN: From this screen you can set your profile and preferences. Press the SETTINGS button on the Mode Select Screen to set your personal profile and customize system preferences such as Timer Presets, Audio Settings and Screen Settings. -
Page 8: Personal Settings
PERSONAL Screen – Weight / Height / Average Stride Length PERSONAL: Under the PERSONAL tab there are two screens: WEIGHT / HEIGHT / AVERAGE STRIDE LENGTH Toggle up and down to the correct values; there is no need to “save” or “enter” because the system accepts a value as entered. -
Page 9: System Settings
SYSTEM Screen – Pomodoro, Short Break, Long Break SYSTEM: The SYSTEM section contains options for language, audio and timer settings. To customize your system, navigate through the following screens using the NEXT PAGE and PREVIOUS PAGE buttons found at the bottom of the console screen. You will see the following screens, in the following order. -
Page 10: Go! - Operating Your Treadmill
GO >>>>> BEGIN 3. BEGIN YOUR ACTIVITY INITIAL SCREEN DISPLAY You now return to the initial screen. In this screen you have the opportunity to select any of the teal-colored activity buttons on this top row. From here you can select: SIT, STAND, or WALK. -
Page 11: Sit Mode
SIT MODE - SCREEN To track time spent sitting, select SIT mode from 00:14 00:00 00:00 the teal-colored mode buttons on the top row. MM:SS MM:SS MM:SS STAND WALK 1 SETTINGS EXIT Now press START. Note that the green START button changes to STOP for when you want to 00:14 0000... -
Page 12: Walk Mode
WALK WALK MODE – SCREEN To track time spent walking, select WALK mode from the teal-colored mode buttons on the top row. Stand on the treadmill deck close enough to be able to use a height adjustable or standing desk and in a safe location where your stride is neither too close to the front or the rear of the belt. -
Page 13: Pomodoro Timer
WALK Measured Data in the Walk mode 00:00 00:19 00 In WALK mode all 4 of the dark blue buttons MM:SS MM:SS MILES (Calories, Time, Steps and Distance) become STAND WALK 1 SETTINGS EXIT active and will track the total respective measurements for the current walking session. -
Page 14: General Maintenance
A soft, micro-fiber components need to be replaced. Contact iMovR Customer Care to cloth like the kind used for cleaning prescription eyeglasses is ideal. - Page 15 The drive belt should only be caps (shown in the image below). tightened by a trained service technician. Contact iMovR Customer Care to locate an iMovR-approved service outlet in your area. Tighten the rear roller only enough to prevent slippage at the front roller. ...
- Page 16 Note that while iMovR’s multi-viscosity formulation can be used on the vast majority of treadmills on the market (see website for the entire list), not all treadmill lubricants on the market are safe to use on the ThermoTread GT. NEVER use WD-40, graphite, Teflon, wax or anything other than 100% Silicone Oil to lubricate this treadmill.
-
Page 17: Troubleshooting Guide
This usually indicates that your treadmill has not been leveled correctly. Follow 7) Treadmill belt does not stay centered all the instructions in the front of this manual pertaining to siting and installing the treadmill. Having Issues? Call Us! iMovR Customer Service: 888-208-6770 or 425-999-3550 9AM-5PM Pacific Time Monday-Friday... -
Page 18: Moving The Treadmill
MOVING THE TREADMILL The ThermoTread GT can be moved by using the 2 recessed caster wheels set into the front of the unit to roll the treadmill into position. It is best to pick the treadmill up carefully from the rear and lift it to about a 45-degree angle in order to enable easier rolling. Please use extreme caution as the treadmill is heavy. -
Page 19: Treadmill - Parts List
To download the most up to date software, connect your USB cable to your computer and visit: http://www.imovr.com/treadmill-software-download IMPORTANT - Use this cord only while updating software on your treadmill. Once finished updating software, unplug the cable from the treamill console. Do not plug... - Page 20 ermoTread Version 1.0 (7/2015)