Subscribe to Our Youtube Channel
Related Manuals for SGS 62CC
Summary of Contents for SGS 62CC
- Page 1 62CC PETROL CHAINSAW OWNER’S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.
-
Page 2: Safety Warnings
Keep away from fire. increase the vibrations transmitted to your hands. A saw with loose components or with damaged or worn AV buffers will also tend to have higher vibration levels. WWW.SGS-ENGINEERING.COM PAGE 2 PAGE 3 CALL FOR ASSISTANCE: 01332 576 850... - Page 3 Always hold the chain saw firmly with both trigger is released. hands when the engine is running. Use a firm grip with thumb and fingers encir- cling the chain saw handles. WWW.SGS-ENGINEERING.COM PAGE 4 PAGE 5 CALL FOR ASSISTANCE: 01332 576 850...
- Page 4 E P F operations. (2) guide bar (3) saw chain ( 2 ) Keep the handles dry, clean and free E N F ( 1 ) of oil or fuel mixture. WWW.SGS-ENGINEERING.COM PAGE 6 PAGE 7 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 5: Kickback Prevention
Only use replacement bars and chains -Steady, methodical work specified by SGS Engineering. -Proper revision of this manual -Good dilligance -A clear visual of your work area WWW.SGS-ENGINEERING.COM... -
Page 6: Chain Brake
Operating level varies by bar size. WWW.SGS-ENGINEERING.COM PAGE 10 PAGE 11 CALL FOR ASSISTANCE: 01332 576 850... -
Page 7: Explanation Of Symbols On The Machine
Shows the directions that the chain brake is re- leased (white arrow) and activated (black arrow). removed and held Position: Front of the chain cover between your feet. WWW.SGS-ENGINEERING.COM PAGE 12 PAGE 13 CALL FOR ASSISTANCE: 01332 576 850... - Page 8 Make sure the prongs in the bottom of the chain are in the goove of the guide bar. 3. Install the bump spike to the power unit. The bump spike will be with two small bolts in your toolkit. WWW.SGS-ENGINEERING.COM PAGE 14 PAGE 15 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 9: Installing Guide Bar And Saw Chain
7. Position the brake plate back in the right place and reattach the tension screw until the chain can barely be moved away it to finger tightness. from the chain bar. WWW.SGS-ENGINEERING.COM PAGE 16 PAGE 17 CALL FOR ASSISTANCE: 01332 576 850... - Page 10 Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itself and the guide bar. RECOMMENDED MIXING RATIO PETROL 25 : OIL 1 WWW.SGS-ENGINEERING.COM PAGE 18 PAGE 19 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 11: How To Mix Fuel
3. Stop the engine before refueling the unit. Be sure to sufficiently agitate the mixed fuel in the container. 6. Indicate the contents on outside of container for easy identification. WWW.SGS-ENGINEERING.COM PAGE 20 PAGE 21 CALL FOR ASSISTANCE: 01332 576 850... -
Page 12: Chain Oil
If not, the chain may become rusted. Chain rust will cause the chain to become rigid or for the chain oil to become viscous at the tip. WWW.SGS-ENGINEERING.COM PAGE 22 PAGE 23 CALL FOR ASSISTANCE: 01332 576 850... -
Page 13: Starting The Engine
The oil tank should become nearly empty by NOTE the time fuel is used up. Be sure to refill the oil tank every time when refueling the saw. WWW.SGS-ENGINEERING.COM PAGE 24 PAGE 25 CALL FOR ASSISTANCE: 01332 576 850... -
Page 14: Adjusting The Carburetor
If the idling speed is too slow, turn the screw clockwise. 4. Make a test cut and adjust the H needle for best cutting power, not for maximum speed. WWW.SGS-ENGINEERING.COM PAGE 26 PAGE 27 CALL FOR ASSISTANCE: 01332 576 850... - Page 15 If the wear is considerable, replace it with a new sprocket and chain. Never fit a new chain on a worn sprocket, or a worn chain on a new sprocket. WWW.SGS-ENGINEERING.COM PAGE 28 PAGE 29 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 16: Periodical Service Points
With a wire hook, remove the oil filter from the feeding port. Wash the filter with petrol. WARNING Take care not to fold the suction pipe. WWW.SGS-ENGINEERING.COM PAGE 30 PAGE 31 CALL FOR ASSISTANCE: 01332 576 850... - Page 17 If you do not attach the muffler correctly, when running the engine, the muffler will be loose and the exhaust gases can escape at a much higher temperature than usual. WWW.SGS-ENGINEERING.COM PAGE 32 PAGE 33 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 18: Maintenance Of Saw Chain And Guide Bar
Make sure the saw chain is held securely. • Make sure the engine has stopped. Make the shoulder • Use a round file of proper size for the chain. round Depth gauge standard WWW.SGS-ENGINEERING.COM PAGE 34 PAGE 35 CALL FOR ASSISTANCE: 01332 576 850... - Page 19 Make sure every cutter has the same length and edge to be corrected or replaced. angles as illustrated. Cutter length Ruler Filing angle Side plate angle Top plate angle No gap Chain tilts WWW.SGS-ENGINEERING.COM PAGE 36 PAGE 37 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 20: Troubleshooting Guide
TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Starting failure Oil does not come out Lack of power/Poor acceleration/Rough idling WWW.SGS-ENGINEERING.COM PAGE 38 PAGE 39 CALL FOR ASSISTANCE: 01332 576 850... -
Page 21: Parts Diagram
Tension Screw 904479 904514 Spark Plug Socket Brake Spring Cover 904480 904515 Wrench Fixed Shrapnel Chain 904481 SCSCHAIN20 Oiler Chain Guide 904482 SCSBAR20 Engine Stop Chain Guide Sleeve 904483 904518 WWW.SGS-ENGINEERING.COM PAGE 40 PAGE 41 CALL FOR ASSISTANCE: 01332 576 850... - Page 22 PARTS DIAGRAM PARTS LIST WWW.SGS-ENGINEERING.COM PAGE 42 PAGE 43 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 23: Ec Declaration Of Conformity
SGS Engineering (UK) Ltd TECHNICAL SPECIFICATIONS West Side Park Raynesway Derby, DE21 7AZ Power Unit EC Declaration of Conformity Displacement 62cc Fuel Mixture Petrol 25 : Two Stroke Oil 1 Fuel tank capacity 550 cm3 Oil tank capacity 260 cm3 MANUFACTURER’S NAME:...
Need help?
Do you have a question about the 62CC and is the answer not in the manual?
Questions and answers