1. Manuals
  2. Brands
  3. U-Media Manuals
  4. Modem
  5. WMD-360A
  6. User manual

U-Media WMD-360A User Manual

802.11g wireless mimo minipci module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
802.11g Wireless MIMO miniPCI Module
User's Guide
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WMD-360A and is the answer not in the manual?

Questions and answers

Summary of Contents for U-Media WMD-360A

  • Page 1 802.11g Wireless MIMO miniPCI Module User's Guide...
  • Page 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 3: Federal Communications Commission Interference Statement

    20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. U-MEDIA declares that WMD-360A, ( FCC ID: SI5WMD360A ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
  • Page 4 Distance between two external antennas on housing is 15cm, and PLS refer to the following picture for antenna position.

  • Page 5: Table Of Contents

    Table of Contents Federal Communications Commission Interference statement____1 Getting Started_____________________________________________4 About Your 802.11g/b WLAN MIMO mPCI______________________4 Configuring Wireless Security_______________________________4 Configuring Security_____________________________________4 Configuring WEP__________________________________________4 Configuring WPA-PSK______________________________________7 Configuring WPA__________________________________________8 Configuring 802.1x_______________________________________8 Configuring 802.1x – EAP-MD5_____________________________8 Configuring 802.1x – EAP-LEAP____________________________9 Configuring 802.1x – EAP-PEAP____________________________9 Configuring 802.1x –...

  • Page 6: Getting Started

    Getting Started This chapter introduces the module and prepares you to use the Wireless Utility. About Your 802.11g WLAN MIMO mPCI The Module is an IEEE 802.11b, and 802.11g compliant wireless LAN adapter. With the Module, you can enjoy wireless mobility within almost any wireless networking environment. The following lists the main features of your Module.
  • Page 8 1. Select [WEP] under [Security Mode] 2. Put a check mark next to [Using Static WEP] 3. Click [Config]. You will then see the screen below. 4. [WEP Method] Select the correct encryption level to match your access point. Either 64, 128, or 152-bit.

  • Page 9: Configuring Wpa-Psk

    Manual Input (Hexadecimal): You generate your own WEP Key using hexadecimal characters (10 characters for 64-bit, 26 characters for 128-bit, 32 characters for 152-bit). 5. Click [OK] to save your settings and return to the previous screen. 6. If you want to use 802.1x authentication with WEP, you will need to configure your 802.1x settings.

  • Page 10: Configuring Wpa

    Configuring WPA 1. Select [WPA-PSK] under [Security Mode]. 2. Select [Encryption method]. You can choose between TKIP or AES. Most access points use TKIP for WPA. 3. See section 4.5 for configuring 802.1x for WPA. Configuring 802.1x 1. Choose the EAP method under [Authentication protocol]. 2.

  • Page 11: Configuring 802.1X - Eap-Leap

    Configuring 802.1x – EAP-LEAP 1. Enter in unique User ID and Password under [User Information] Configuring 802.1x – EAP-PEAP 1. Click [Config] under [Authentication protocol] 2. Select inner PEAP protocol. You choices are [MS-CHAP v2] or [TLS]. 3. Click [OK] to finish and return to the previous screen. 4.
  • Page 12 [Use user certificate]: Put a check in the box to activate user certificate. Then select certificate from the pull down menu. [Validate server certificate]: Put a check in the box to activate server certificate. Then select the certificate authority from the pull down menu. [Server name]: Name of server used for 802.1x authentication.

  • Page 13: Configuring 802.1X - Eap-Tls

    Configuring 802.1x – EAP-TLS 1. Enter in unique User ID and Password under [User Information]. 2. TLS requires you to configure both a server and user7 certificate. 3. Click [Config certificate]. The following window appears: You must first have a wired connection to a network and obtain the certificate(s) from a certificate authority (CA).
  • Page 14 [Use user certificate]: Put a check in the box to activate user certificate. Then select certificate from the pull down menu. [Validate server certificate]: Put a check in the box to activate server certificate. Then select the certificate authority from the pull down menu. [Server name]: Name of server used for 802.1x authentication.

  • Page 15: Configuring 802.1X - Eap-Ttls

    Configuring 802.1x – EAP-TTLS 1. Enter in unique User ID and Password under [User Information]. 2. Select inner TTLS protocol. You can choose between [PAP], [CHAP], [MS-CHAP], [MS-CHAPv2], or [MD5-Challenge]. 3. Click [OK] to finish and return to the previous screen. 4.
  • Page 16 [Use user certificate]: Put a check in the box to activate user certificate. Then select certificate from the pull down menu. [Validate server certificate]: Put a check in the box to activate server certificate. Then select the certificate authority from the pull down menu. [Server name]: Name of server used for 802.1x authentication.

Table of Contents