Table of Contents
Advertisement
Quick Links
Vivint Pandora360
Operating Instructions
Title
Pandora360 Operating Instructions
Id
Type
805-SXC0002-001
Customer Operation Instruction
Date
Security
2018-09-22
Internal
1.
1. Introduction
2. Radio Frequency Exposure
3. Directions for Use
3.1. Preconditions
o
3.2. Intended Use
o
4. Installation Procedure
4.1. Tools for Installation
o
4.2. Unpacking
o
4.3. Installing
o
5. Technical Specification
6. Fault, Possible Causes, and Remedies
7. Standards
8. Glossary
4.3.1. Pole Installation
4.3.2. Cable Installation
4.3.3. Pandora360 Installation
4.3.4. Testing the Installation
4.3.5. Software Installation
Page 1 of 15
Prepared
P. Estelius
Revision
A
Advertisement
Table of Contents
Summary of Contents for Vivint Pandora360
-
Page 1: Operating Instructions
Vivint Pandora360 Operating Instructions Title Pandora360 Operating Instructions Type Prepared 805-SXC0002-001 Customer Operation Instruction P. Estelius Date Security Revision 2018-09-22 Internal 1. Introduction 2. Radio Frequency Exposure 3. Directions for Use 3.1. Preconditions 3.2. Intended Use 4. Installation Procedure ... - Page 2 (57-64 GHz) based on WiGig technology, IEEE 802.11ad. It can provide 2 Gbps user traffic in each direction (four directions giving 8 Gbps in total). Pandora360 comes in two versions, either with an additional LAN port, or with an SFP+ (10Gbps) port. It is powered by proprietary Power over Ethernet (PoE) or 48 VDC.
- Page 3 Figure 2: Horizontal Radio Sectors on the Pandora360 Node, Page 3 of 15...
- Page 4 Qualcomm baseband and RF chipset. Figure 3: Vertical adjustment of the Pandora360 Radio Lobe. The Pandora360 comes in two variants, one with two RJ45 Ethernet connections, and one for one RJ45 and one SFP+ Ethernet connection. Both variants deliver Gigabit connections on both inputs.
-
Page 5: Radio Frequency Exposure
Avoid operating this product at a distance less than 11 in (28 cm) from the user. 3. Directions for Use The Pandora360 is designed for outdoor use in broadband radio mesh setups. This means for example University campuses, local housing areas, etc. The small size makes it less obvious in the environment, and its WiFi management connection makes local management and maintenance from ground safe and easy for the maintenance personnel. -
Page 6: Intended Use
Hands on work on the equipment is only required at installation, or if service is required. 3.1. Preconditions The preconditions for using a Pandora360 is that the installation and use in all parts follow what has been stated by the supplier and manufacturer. -
Page 7: Pole Installation
The Pandora360 node is installed as follows: 4.3.1. Pole Installation Pandora360 installer's Tools will direct the installer where the unit can be located on the roof (typically a polygon is defined). The unit will need to report it's correct GPS position back to the IT systems to verify the node is installed at the correct site. - Page 8 4. In case of field termination, crimp the connectors to the cables 4.3.3. Pandora360 Installation Install the Strain Relief with the two MRT M3x8 screws to the bottom side of Pandora360 in preparation for cable connection. Take the Pandora360 node together with sleeve gasket and sleeve gasket plug up on the roof to the point of installation.
-
Page 9: Software Installation
Vivint's IT systems. On site an installer will scan the node (label on the Pandora360 node) in order to register the node and connect it with the customer site. At the point of scan, the customer record and the equipment are linked to each other. This is a critical point at which the configuration for the unit is available through the ACS. -
Page 10: Technical Specification
5. Technical Specification The technical Specifications of the Pandora360 node are as follows: Comment SFP+/RJ45 VI-PAN001-110 Unit Type(s) VI-PAN002-110 RJ45/RJ45 Unit Model CE04 Occupied Bandwidth: 1760 MHz with 2160 (Multi)Point-to- MHz as Radio Type Multi-Point Radio channel separation according to IEEE 802.11ad... - Page 11 Nominal 53VDC (42.5- 57VDC), 1A max. Power 48 VDC, or Supply Proprietary PoE Input: 53VDC (42.5- 57VDC), 1A Placed 90 No of Radios 4 degerees apart. Radio Lobe Approx. 5 degrees Width (Deg) Antenna 23 dBi Effective Gain Output Max values 40 dBm average, Power measured at...
- Page 12 For remote node management. WiFi IEEE 802.11b/g/n Connection (2.4 GHz only with Channels 1 to 11) with FCC & IC ID Distance Between Max: 300 m Nodes Usage Outdoor Operating -40°C to +55°C (- Temperature 40°F to +131°F), Relative Humidity 4-100% Range When...
- Page 13 Restart the node. Denied disturbances. Caution: The Pandora360 may be powered by more than one power source to ensure uninterrupted service. To de-energize a Pandora360, disconnect all power sources. 7. Standards Vivint, Inc. 4931 N. 300 W. Provo, UT 84604 USA...
- Page 14 - Consult the dealer or an experienced radio/TV technician for help. NOTICE: Changes or modification not expressly approved by Vivint could void the user’s authority to operate this equipment. FCC ID: 2AAAS-CE04 Contains FCC ID: Z64-WL18SBMOD (2.4 GHz 802.11b/g/n radio) ETL LISTED: Conforms to ANSI/UL Std.
- Page 15 PoE Power over Ethernet, way of powering equipment thrpough an Ethernet cable. SFP Small Form-factor Pluggable transciever, type of connector. Page 15 of 15...
Need help?
Do you have a question about the Pandora360 and is the answer not in the manual?
Questions and answers