Related Manuals for IOGear GWHDKITD
Summary of Contents for IOGear GWHDKITD
- Page 1 Quick Start Guide Wireless TV Connection with Dongle GWHDKITD PART NO. Q1504-b www.iogear.com...
-
Page 2: Product Introduction
Package Co ents 1 x GWHDKITD Transmitter 1 x IR Blaster Cable 1 x GWHDKITD Receiver 1 x IR Receiver Extender Cable 1 x 3 feet HDMI Cable 1 x Antenna 1 x HDMI Extender Cable 1 x DC5V/2A Wall Mount Switching Power Supply... -
Page 3: System Requirements
Features 1. Compliant with HDMI 1.3 and HDCP 1.2. 2. Highest resolution up to 1080p full HD. 3. Strong anti-interference by operating at 5GHz frequency. 4. Support point to point wireless configuration. 5. Support IR pass back with 20-60KHz frequency. 6. - Page 4 Overview Transmitter A. HDMI input B. Wireless connection indicator C. Power input D. Power indicator E. IR blaster cable connector B C D Receiver Back F. Power input G. Power indicator H. Wireless connection indicator I. HDMI output connector J. IR receiver extender cable connector K.
-
Page 5: Hardware Installation
Hardware Installation Please read safety instructions carefully before installation and operation: 1. Please pay attention to all the warnings and hints for this device. 2. Do not expose this unit to rain, moisture or liquid. 3. Do not insert any foreign object into the device. 4. - Page 6 Hardware Installation Transmitter STEP 1 Insert the transmitter into an open HDMI port on the video source device (Blu-ray, computer, media player, etc.). In case the space is too tight around the HDMI port, or the position of the HDMI port is at an awkward angle and could possibly cause a connection issue, use the HDMI cable extension cable included in the package to increase the space or correct position issues.
- Page 7 Hardware Installation Receiver STEP 4 Install the antenna to the receiver STEP 5 (Disregard this step if skipped in step 3) Take the IR In for RX cable from the box, insert IR RX cable to the IR In port on the receiver; peel off the protective paper from the sensor end of the cable and place it with the round area of the IR sensor facing out towards the viewing area, the IR RX sensor must be able to receive the signal from the video source device remote control.
- Page 8 Hardware Installation STEP 7 Connect DC5V/2A power supply to the Receiver power input port STEP 8 Power on the video source device, then power on the video display. The power indicator LED’s should be lit on both the transmitter and the receiver indicating they are powered on.
- Page 9 3. Check the HDMI cable connection at both sides to make sure they are plugged in firmly; If all of the above has been checked and there is still no video displayed, contact IOGEAR Technical Support for further support.
-
Page 10: Specification
Specification Items Specifi cation Voltage/Current Transmitter: DC5V/1A Receiver: DC5V/2A Power supply Power consumption TX < 3W Rx < 5W HDMI compliance HDMI 1.3 HDCP compliance HDCP 1.2 480i@60Hz, 480p@60Hz, 576i@50Hz, HDMI resolution supported 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz Supports audio formats L/R stereo audio HDMI performance... -
Page 11: Compliance Information
Compliance Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 12: Limited Warranty
Important Product Information Product Model Serial Number Contact WE’RE HERE TO HELP YOU! NEED ASSISTANCE SETTING UP THIS PRODUCT? Make sure you: 1. Visit www.iogear.com for more product information 2. Visit www.iogear.com/support for live help and product support IOGEAR https://iogear.custhelp.com support@iogear.com www.iogear.com...
Need help?
Do you have a question about the GWHDKITD and is the answer not in the manual?
Questions and answers