Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Premier AC720
Summary of Contents for Premier AC720
- Page 1 SKID STEER LOADER AMMBUSHER HEAVY DUTY BRUSH CUTTER MODEL: AC720 OPERATOR’S MANUAL SERIAL NUMBER: ____________________ WARNING! AVOID INJURY OR DEATH! READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT!
-
Page 3: Table Of Contents
TABLE OF CONTENTS …………………………………………………..Letter to the Owner …………………………………………………..Warranty Policy …………………………………………………..Warranty Registration Form …………………………………………………..Safety Information …………………………………………………..Hook-Up Procedures To Remove Brush Cutter Attachment …………………………………………………..…………………………………………………..Operating Instructions …………………………………………………..9-12 Repair and Maintenance …………………………………………………..Bill of Materials …………………………………………………..14-19 Parts List Diagrams... - Page 4 E-Mail: contact@premierattach.com Premier strives to provide superior products and the highest level of customer service. If you have any suggestions on how we can improve for the future, we would appreciate hearing from you. Thank you for putting your trust in PREMIER.
-
Page 5: Warranty Policy
This warranty constitutes the entire warranty of PREMIER, and no oral representations, warranties or guarantees by any agent of PREMIER or the seller shall be binding on PREMIER, and no part of this warranty may be modified or extended except upon the express written consent of PREMIER. -
Page 6: Warranty Registration Form
MODEL_________________________________ APPLICATION_______________________________________________________________________________ This PREMIER Ammbusher Heavy Duty Brush Cutter has been accepted in good condition and I have been instructed by the dealer to read and understand the entire Operator’s Manual for proper installation, proper and safe operation, preventative maintenance, service, warranty, and all other information covered in the Operator’s Manual. - Page 7 #1 - Fold down here From: ________________________________ Place Postage ________________________________ Here ________________________________ PREMIER 2707 Lofty Drive Fort Wayne, IN 46808 #2 - Fold up here #3 - Tape or seal here...
-
Page 8: Safety Information
It is the responsibility of all operators to read and understand this entire manual before installing, operating or servicing the PREMIER Ammbusher Heavy Duty Brush Cutter. Pay particular attention to cautions, warnings and safe operating procedures. Be a safe and qualified operator. Operate your equipment with care and good judgment and see to it that it is properly maintained. -
Page 9: Safety Information
Do not raise the back of the PREMIER Brush Cutter (nearest operator) over 2 feet off the ground. Never expose yourself or a bystander to the rotating blades. When driving the loader to and from the worksite, carry the PREMIER Brush Cutter as low as possible to the ground to avoid the possibility of tipping forward. -
Page 10: Hook-Up Procedures
Release the locking levers and disengage the loader mounting plate. OPERATING INSTRUCTIONS The PREMIER Ammbusher Heavy Duty Brush Cutter is capable of cutting trees and vegetation of varying height up to 7” in diameter. Designed to make your loader more versatile, the PREMIER Ammbusher Heavy Duty Brush Cutter is intended to perform these functions without the front of the mower deck being raised to a vertical height greater than 3 feet. -
Page 11: Repair And Maintenance
REPAIR AND MAINTENANCE PART “A” BLADE CARRIER REMOVAL This operation should be performed by an authorized dealer or a qualified technician. The blade carrier weighs approximately 600 pounds. Should it unexpectedly shift during removal, it could result in personal injury. An overhead hoist with the appropriate lifting capacity is recommended for this operation. - Page 12 Repeat the above process on all 3 remaining blades. NOTE: Only use genuine PREMIER Ammbusher replacement parts. It is recommended to flip all blades at the same time. Blades should be replaced in pairs on opposite sides of the blade carrier to maintain balance.
- Page 13 REPAIR AND MAINTENANCE PART “E” MOTOR REMOVAL 1. Set the Brush Cutter flat on the ground. Turn the skid loader engine off to disconnect the hydraulic hoses from the loader. Then, safely disconnect the Brush Cutter from the loader. 2. Remove the motor cover. 3.
- Page 14 REPAIR AND MAINTENANCE PART “G” CHANGING OIL IN THE BEARING HUB NOTES: It is recommended that an oil pump is used for the removal of the old oil from the bearing hub. The proper oil level is approximately 2” from the top of the plug hole on the bearing hub housing. Be careful not to overfill.
-
Page 15: Bill Of Materials
BILL OF MATERIALS PART # QTY. PART DESCRIPTION 61082 AC Hydraulic Pressure Gauge 40005 16 1/2" Crown Lock Flange Nut 61083 AC Hyd Gauge Hose, 1/4" NPTF x #4F JIC x 24" Long 4 1/2"-13 x 2” HHCS 40006 61084 AC Case Drain Hyd Hose, #6F JIC x #4MB x 29"... -
Page 16: Parts List Diagrams
PARTS LIST DIAGRAMS Figure A: Full Assembly REF. # PART # QTY. PART DESCRIPTION 85161 5/16" x 3/4" Self-Tap SC-HWSLTCS 85371 Mini Manual Holder 70111 87529 AC/AD Carbide Tooth Service Door 87530 AC/AD Blade Service Door 87579 AC/AD Chain Bar Cover, Right 87585 AC Runner, Left 87586... - Page 17 Figure B: Blade Carrier REF. # PART # QTY. PART DESCRIPTION 3/4”-10 Top Lock Nut 40035 40065 3/4"-10 x 3" HHCS, Grade 8 40067 3/4" Nord-Lock Washer 40069 5/8"-18 Crown Lock Nut, Grade 8 40073 3/4"-10 x 3-1/4" HHCS, Grade 8 AC Carrier Spacer 87533 87534...
- Page 18 Figure C: Bearing Hub & Motor REF. # PART # QTY. PART DESCRIPTION 1/2"-13 x 2” HHCS 40006 5/16” Split Lock Washer 40055 40074 5/8" Nord-Lock Washer 40075 5/16"-18 x 1" HHCS, Grade 5 40076 5/16" Flat Washer, Grade 5 5/8"-11 x 1-3/4"...
- Page 19 Figure D: Manifold Assembly & Hose Kit REF. # PART # QTY. PART DESCRIPTION 5/16” Split Lock Washer 40055 40075 5/16"-18 x 1" HHCS, Grade 5 40076 5/16" Flat Washer, Grade 5 40077 5/16"-18 Crown Lock Nut, Grade 5 40079 5/16"-18 x 5"...
- Page 20 Figure E: Back Section REF. # PART # QTY. PART DESCRIPTION 3/8”-18 Top Lock Nut 40015 5/16” Split Lock Washer 40055 40070 1/4"-20 x 1-1/2" HHCS, Grade 5 40072 1/4" Crown Lock Nut, Grade 5 40075 5/16"-18 x 1" HHCS, Grade 5 5/16"...
- Page 21 Figure F: Right Side Section REF. # PART # QTY. PART DESCRIPTION 40005 1/2" Crown Lock Flange Nut 45008 1/2"-13 x 1-3/4" HHCS, Grade 5 45011 1/2" Flat Washer, Grade 5 45020 1/2" x 1-1/4" Carriage Bolt 87584 AC Runner, Right AC Skid Shoe 88125...
- Page 22 NOTES...
Need help?
Do you have a question about the AC720 and is the answer not in the manual?
Questions and answers