Advertisement
Quick Links
Cat 30 (Standard) and Cat 31 (Metric)
Product Information and Usage Guide
(Import) (Metric is used in demonstrations)
Metric
Standard
Components of Gauge and Overview:
The CAT 30 (standard) and CAT31 (metric) gauges are composed of
stainless steel and can be used to obtain a wide range of
measurements. These gauges consists of five major components
from which measurements can be taken. They are the rotating fan,
working edge, main ruler, side slide with point and center slide.
Some types of measurements that can be taken include but our not
limited to; butt weld height, undercut, angle of preparation or bevel,
gap size, leg of fillet weld throat of fillet weld and the face of the
butt weld.
PO BOX 218 ● STEVENSVILLE, MI ● 49127
PHONE: 269‐465‐5750 ● FAX: 269‐465‐6385
WEBSITE: www.galgage.com
Advertisement
Summary of Contents for G.A.L. Gage CAT 30
- Page 1 Cat 30 (Standard) and Cat 31 (Metric) Product Information and Usage Guide (Import) (Metric is used in demonstrations) Metric Standard Components of Gauge and Overview: The CAT 30 (standard) and CAT31 (metric) gauges are composed of stainless steel and can be used to obtain a wide range of measurements. These gauges consists of five major components from which measurements can be taken. They are the rotating fan, working edge, main ruler, side slide with point and center slide. Some types of measurements that can be taken include but our not limited to; butt weld height, undercut, angle of preparation or bevel, gap size, leg of fillet weld throat of fillet weld and the face of the butt weld. PO BOX 218 ● STEVENSVILLE, MI ● 49127 PHONE: 269‐465‐5750 ● FAX: 269‐465‐6385 WEBSITE: www.galgage.com...
- Page 2 Components of Gauge and Tolerances Rotating Fan Working Edge Main Ruler Center Slide Side Slide with Point PO BOX 218 ● STEVENSVILLE, MI ● 49127 PHONE: 269‐465‐5750 ● FAX: 269‐465‐6385 WEBSITE: www.galgage.com ...
- Page 3 Application and Methods Measuring the Height of the Butt Weld (Figure 1) To measure the height of a butt weld first align the side slide with point and the main ruler to zero. Tighten the screw so that the side slide with point cannot move. Straddle the weld that you wish to measure in‐between the side slide with point and the working edge of the gauge. The side slide with point and the working edge of the gauge should create a level surface which will enable an accurate measurement to be taken. Loosen the screw of the center slide and slide the tip down to the top of the butt weld. Tighten the screw of the center slide and take measurement. Figure 1 Measuring the Leg of the Fillet Weld (Figure 2) To measure the leg of a fillet set the working edge of the gauge on top of the weld. Loosen the screw of the center slide and move until the bottom tip of the center slide touches the base of where the weld lies. Tighten the screw of the center slide. The measurement on the center slide will be the measurement for the leg of a fillet. Figure 2 PO BOX 218 ● STEVENSVILLE, MI ● 49127 PHONE: 269‐465‐5750 ● FAX: 269‐465‐6385 WEBSITE: www.galgage.com ...
- Page 4 Application and Methods Measuring the throat of a fillet weld (Figure 3) To measure the throat of a fillet weld first set the side slide with point and the main ruler to zero, this will ensure that you are able to use the slanted edges at the top without interference. Position the gauge so that the one slanted edge touches the base of where the weld is located and the other slanted edge touches just above the where the weld is. This will allow the center slide access to the top of the fillet weld. Move the center point down so that it touches the top of the weld and tighten the screw. Read the indicating measurement from the center slide. Figure 3 Measuring the face of a butt weld (Figure 4) To measure the face of the butt weld first make sure that the side slide with point is raised so that the point is out of the way and will not interfere with measuring. Also, you will be using the back of the gauge for this measurement. On the side with the side slide with point set the bottom edge of the gauge on one side of the weld. Then lower the rotating fan until the point touches the other side of the weld. The measurement will be indicated on the back of the gauge on the chart provided. Figure 4 Distributed by: ABQ Industrial LP USA Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...
- Page 5 Application and Methods Measuring the angle of preparation (bevel) (Figure 5) To measure the angle of preparation (bevel) use the back side of the gauge. Set the gauge on top of the pipe or place where measurement is needed. The center slide should be parallel to the pipe or where measurement is needed. Lower the rotating fan until the side touches the angle that needs to be measured. Read measurement from chart provided. Figure 5 Measuring the undercut of a weld (Figure 6) To measure the depth of the undercut set the center slide to zero and tighten the screw. Position the side slide with point over the undercut. Lower the side slide with point into the undercut and tighten the screw. The measurement for the depth of the undercut can be read off the scale that is on the side slide with ruler. Figure 6 Distributed by: ABQ Industrial LP USA Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...
- Page 6 Application and Methods Measuring the Fit‐Up Gap (Figure 7) and (Figure 8) To measure the fit‐up gap turn the gauge to the back side. Lower the rotating fan so that the point of the gauge is free from contact with the main gauge itself. The range of measurement allowed on the point of the is 0.5mm to 5mm (1/32 to 3/16 inches ) . Lower the point in‐ between the gap. Continue to lower until both sides touch the top of the gap. Read measurement from the lines on the rotating fan. Figure 7 Figure 8 Distributed by: ABQ Industrial LP USA Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...