Do you have a question about the 7 Station Sports Series and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Fitness Reality Kids 7 Station Sports Series
Page 1
7 Station Sports Series Metal Swing Set with Basketball and Soccer OWNER’S MANUAL 8452.2-071217 CAUTION: This unit is designed to be used safely by up to 6 children between the ages of 3 years to 8 years old with a maximum weight of 80 pounds (36.3kgs) each, simultaneously,...
Page 2
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. STOP. Contact customer service if you have any questions regarding assembly or proper operation of the machine. Email us at: Service@paradigmhw.com Or call us at: 1-844-641-7920 Hours: 8:00 am to 5:00 pm (PST) Daily...
TABLE OF CONTENTS SERVICE LABEL PLACEMENT SAFETY OVERVIEW DRAWING PARTS TOOLS REQUIRED FOR ASSEMBLY ANCHOR INSTALLATION ASSEMBLY INSTRUCTIONS WARRANTY PARTS REQUEST FORM...
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods: For The Best Service, please Email: service@paradigmhw.com Response Time: 1-2 Business Days Emailing us with the information above will be the best method to receive a response during peak business hours Website:...
SAFETY Read all instructions carefully before assembling operating this product. Retain this Owner’s manual and keep the original purchase receipt for future reference. Before assembling the Fitness Playground, find level ground no less than 6 feet from any structure or obstruction to the Fitness Playground. The Fitness Playground must have clearance on all sides.
PARTS Parts used for main frame assembly 1 PC Top bar 1 PC Top bar Top Bar and Legs 1 PC Support 2 PCS Padded Leg 2 PCS 1 PC Slide Mounting Bar 1 PC Crossbar Basketball Hoop 1 PC Support Tube 1 PC Net Bar A...
Page 9
PARTS (Preassembled) (Preassembled) Net Bar Cap 4 SETS (2 Sets preassembed)
Page 10
PARTS Binder Post & Bolt Set M8x15 Bolt 2 SETS 10x50 Sleeve Nut 12 SETS Binder Post & Bolt Set M6x12 Bolt 8x48 Sleeve Nut Binder Post & Bolt Set M6x12 Bolt 4 SETS 8x45 Sleeve Nut Parts used for basketball board assembly Basketball Hoop Support 1 PC...
Page 11
PARTS Hardware used for basketball board assembly Binder Post & Bolt Se t M6x12 Bolt 1 SE T 8x48 Sleeve Nut Bolt S et 5 SETS M6x15 Bolt Parts used for trapeze assembly 1 PC Trapeze Tube Hardware used for trapeze assembly Bolt Set 2 SETS (Preassembled)
Page 12
PARTS Parts used for swing seats assembly 4 PCS Swing Chain (preassembled on the seat) 2 PCS Swing Seat Hardware used for swing seats assembly Female Bolt Set (Preassembled) 4 SETS 4 SETS Eye Bolt Set (Preassembled) Screw Hook 4 PCS (Preassembled) Screw Hook C ap Se t 4 SETS...
Page 13
PARTS Parts used for glider assembly 2 PCS Glider Vertical Pole 2 PCS Glider Horizontal Pole 2 PCS Foot Rest Glider Seat 2 PCS 1 PC Glider Attachment 4 PCS Glider Vertical Pole Cap...
Page 14
PARTS Hardware used for glider assembly Binder Post & Bolt Set 2 SETS M6x12 Bolt 8x73 Sleeve Nut Bolt Set M6x40 Bolt 2 SETS Bolt Set 4 SETS M6x38 Bolt 2 SETS Binder Post & Bolt Set M6x12 Bolt 8x40 Sleeve Nut Glider Bolt Set 1 SET 10x30 Sleeve Nut...
Page 15
PARTS Parts used for slide assembly Slide Ladder Support Tube 1 PC Slide Ladder Connecting Tube 1 PC Slide Leg Tube 2 PCS Slide Ladder Step 2 PCS Connecting Plate 2 PCS Cap for Z1 and Z2 (Preassembled) 2 PCS Cap for Z3 (Preassembled) 2 PCS Slide...
Page 16
PARTS Hardware used for slide assembly 4 SETS Bolt Set M6x36 Bolt Bolt Set 4 SETS M6x42 Bolt Binder Post & Bolt Set M6x12 Bolt 10 SETS 8x24 Sleeve Nut...
TOOLS REQUIRED FOR ASSEMBLY Prepare the following tools prior to assemble this equipment. Hammer Tape Measure Phillips Screwdriver 10, 13 mm Wrench (Included) 5mm Allen Wrench 5mm Allen Wrench with Phillips Screwdriver (Included) (Included)
ANCHOR INSTALLATION For proper installation, the Anchors (A12) must be cemented into the ground. Dig a 15 x 15 x 30 cm hole at each leg. Pour cement into the hole and place the Anchor (A12) at a 5 degree angle, towards the inside of the Playground. Do not use until cement has dried.
ASSEMBLY Place the playground equipment on level ground, not less than 6 feet (1.8 meters) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard ...
Page 20
ASSEMBLY Step 1 Attach the Top Bar (A1B) to the Top Bar (A2B) using two Binder Post and Bolt Sets (Aa2). Tighten the Binder Post and Bolt Sets (Aa2) with the 5mm Allen Wrench aprovided. Slide the Top Bar and Legs Support (A3) over the Top Bar (A1B) and insert the Basketball Hoop ...
Page 21
ASSEMBLY Secure the Basketball Hoop (B3) to the Basketball Backboard (B4) and Basketball Hoop Support Tube (A7) using three Bolt Sets (Ba2). Tighten the Bolt Sets (Ba2) using the 5mm Allen Wrench and 10, 13 mm Wrench provided. Attach the Basketball Hoop Support Tube A (B1) and Basketball Hoop Support Tube B (B2) to ...
Page 22
ASSEMBLY Step 5 Attach two Legs (A4) to the Top Bar (A2B) using four Binder Post and Bolt Sets (Aa3). On the Opposite side, Attach two Padded Legs (A4A) to the Top Bar and Legs Support (A3) using four Binder Post and Bolt Sets (Aa3).
Page 23
ASSEMBLY Spread out the Soccer Net (A11) flat on the ground and find each end. Starting at the Narrowest end, weave the Soccer Net (A11) up both Padded Legs (A4A) as shown in Fig. A. Then weave the Crossbar (A6) Through the top of the Soccer Net (A11) as shown in Fig. B. Secure the Crossbar (A6) to the Padded Legs (A4A) using two Binder Post and Bolt Sets (Aa4).
Page 24
ASSEMBLY Weave the Net Bar A (A8) halfway through the Soccer Net (A11) on the left side. Weave the Net Bar B (A9) halfway through the Soccer Net (A11) on the right side. Insert the tube of the Net Bar (A9) into the Net Bar A (A8), ensure that the metal tab snaps into place.
Page 25
ASSEMBLY Step 9 Using the Velcro straps, attach a Triangle Net (A10) to the Legs (A4) and Slide Mounting Bar (A5). Using the Velcro straps, attach another Triangle Net (A10) to the Padded Legs (A4A) and Crossbar (A6) Using the Veclro straps. Step 1 ...
Page 26
ASSEMBLY Step 11 Attach the Trapeze Tube (P1) to the two pairs of Eye Bolts (Pa2) attached to the Top Bar (A1B). NOTE: Place the Trapeze Tube (P1) in the middle set of Eye Bolts (Pa2) .
Page 27
ASSEMBLY Step 11 Attach a Swing Seat (J2) and two Swing Chains (J1) to the Eye Bolt Sets (Ja2) on Top Bar (A1B) and Top Bar (A2B). Attach a Swing Seat (J2) and two Swing Chains (J1) to the Eye Bolt Sets (Ja2) on Top Bar (A1B).
Page 28
ASSEMBLY Step 12 Attach a Foot Rest (D3) to the Glider Vertical Pole (D1) with the Bolt Set (Da2). Tighten the Bolt Set (Da2) using the 10, 13 mm Wrench provided. Do this for both Glider Vertical Poles (D1). Step 13 Attach the Glider Attachment (D5) onto the Top bar (A1B) with two Glider Bolt Sets (Da5).
Page 29
ASSEMBLY Step 14 Attach a Glider Horizontal Pole (D2) to each side of the Glider Vertical Poles (D1) using two Binder Post and Bolt Sets (Da1). Tighten the Binder Post and Bolt Sets (Da1) using the 5mm Allen Wrench provided. ...
Page 30
ASSEMBLY Align the Align Ladder holes. Leg ho le and Slide ho le here Align the Align Ladder Leg ho le. Support Leg holes. ho le and Slide ho le h ere Step 15 Insert the longer ends of the Slide Ladder Support Tube (Z1) and Slide Ladder Connecting Tube ...
Page 31
ASSEMBLY Step 17 Slide the two Slide Ladder Steps (Z4) up the bottom ends of the Slide Ladder Support Tube (Z1) and Slide Ladder Connecting Tube (Z2). Align the holes of the Slide Ladder Steps (Z4) with the TOP and BOTTOM set of holes on the Slide Ladder Support Tube (Z1) and Slide Ladder Connection Tube (Z2).
Page 32
ASSEMBLY Step 19 Attach the Slide Ladder Connecting Tube (Z2) onto the Slide Mounting Bar (A5) using two Connecting Plates (Z5) and two Binder Post and Bolt Sets (Za3). Tighten Binder Post & Bolt Set (Za3) using the 5mm Allen Wrench and 5mm Allen Wrench with Phillips Screwdriver provided.
Page 33
ASSEMBLY Step 20 Attach a Slide Ladder Support Tube Cross Bar (Z9) onto each side of the ladder using a Binder Post and Bolt set (Za3). Tighten Binder Post & Bolt Set (Za3) using the 5mm Allen Wrench and 5mm Allen Wrench with Phillips Screwdriver provided. Attach a Slide Leg Cross Bar (Z10) to the front of the ladder using two Binder Post and ...
Page 34
ASSEMBLY Step 21 Use the Air Pump (B6) to Pump up the Basketball (B5) and Soccer Ball (A16). There is an inflation needle stored in the handle of the Air Pump (B6).
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO Service@paradigmhw.com NAME:______________________________________________________________________ ADDRESS:__________________________________________________________________ CITY:________________________ STATE:_____________ ZIP:________________________ TELEPHONE: (Day)_________________________________________________________ (Night)________________________________________________________ SERIAL#:____________________________________________________________________ MODEL#:____________________________________________________________________ PURCHASE DATE:____________________________________________________________ PLACE OF PURCHASE:________________________________________________________ PART # DESCRIPTION “YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS” *This form can also be faxed to #: 626-810-2166...
Need help?
Do you have a question about the 7 Station Sports Series and is the answer not in the manual?
Questions and answers