Subscribe to Our Youtube Channel
Related Manuals for Surewerx JET JGP Series
Summary of Contents for Surewerx JET JGP Series
- Page 1 Operator’s MANUAL Prod. No. 111136 111137 JGP SERIES GRIP PULLERS 111138 M18-MH111136-8...
-
Page 2: Table Of Contents
Authorized This warranty does not cover damage Warranty Depots can be found at attributable to normal wear and tear. surewerx.com Any JET product that fails during All warranty claims must be normal use and is within the specified... -
Page 3: Warnings
Authorized Warranty system or configuration that uses at JET’s discretion. Repairs and/ or replacements are warranted as Depots are found at surewerx.com these Grip Pullers. described for the specific product and ALL warranty claims must These instructions include information... -
Page 4: Introduction
JET Grip Puller. this manual. If there are any questions or comments, please This manual contains instructions on installation, safety contact either your local supplier or SureWerx. JET can also precautions, general operating procedures, maintenance be reached at our web site: www.surewerx.com instructions and parts breakdown. -
Page 5: Inserting Wire Rope
INSERTING WIRE ROPE 1. Release the clamp by pushing the clamp lever securely into the notch on the puller body. 2. Insert the end of the wire rope into the rope inlet at the rear of the puller. Feed the wire rope through until it emerges at the other end. -
Page 6: Maintenance
MAINTENANCE Make frequent and careful inspections of the puller. Make Replace the wire rope immediately if: sure puller and wire rope are sufficiently oiled, and that • The thickness of the rope becomes less than they are free of any sand, dirt, dust or other obstruction or half of the original value due to abrasion. -
Page 7: Parts Breakdown And Parts List
JGP75A | 3/4 T GRIP PULLER PARTS BREAKDOWN | PROD. NO. 111136... - Page 8 JGP75A | 3/4 T GRIP PULLER PARTS LIST | PROD. NO. 111136 REF. PART NUMBER DESCRIPTION REQ. REF. PART NUMBER DESCRIPTION REQ. PWC-SGP75-801 SGP75 ANCHOR PIN 8108 PWC-SGP75-8108 SGP75 SCREW BOLT PWC-SGP75-802 SGP75 CASE LEFT/RIGHT ALUMINUM 8109 PWC-SGP75-8109 SGP75A COVER PWC-SGP75-804 SGP75 CRANK AXLE 8110...
- Page 9 JGP150A | 1-1/2 T GRIP PULLER PARTS BREAKDOWN | PROD. NO. 111137...
- Page 10 JGP150A | 1-1/2 T GRIP PULLER PARTS LIST | PROD. NO. 111137 REF. PART NUMBER DESCRIPTION REQ. REF. PART NUMBER DESCRIPTION REQ. 1601 PWC-SGP150-1601 SGP150 ANCHOR PIN 16116 PWC-SGP15-16116 SGP150A INSTRUCTION PLATE 1602 PWC-SGP150-1602 SGP150 CASE LEFT/RIGHT 16202 PWC-SGP150-1604 SGP150 CRANK AXLE ALUMINUM 16206 PWC-SGP150-1616...
- Page 11 JGP300A | 3 T GRIP PULLER PARTS BREAKDOWN | PROD. NO. 111138...
- Page 12 JGP300A | 3 T GRIP PULLER PARTS LIST | PROD. NO. 111138 REF. PART NUMBER DESCRIPTION REQ. REF. PART NUMBER DESCRIPTION REQ. 3201 PWC-SGP300-3201 ANCHOR PIN 32116 PWC-SGP30-32116 INSTRUCTION PLATE 3202 PWC-SGP300-3202 CASE LEFT/RIGHT SIDE 32201 PWC-SGP300-32201 BUSH FOR CRANK AXLE NO LONGER USED 3203 PWC-SGP300-3203...
Need help?
Do you have a question about the JET JGP Series and is the answer not in the manual?
Questions and answers