Advertisement
Quick Links
Advertisement
Summary of Contents for Fly-Dream V3
- Page 1 2.4 GHz Radio Control System www.fd‐rc.com Version: V3.1 Update: V3.1 ...
- Page 2 This ensures safe, stable operation over a wide range of conditions likely to be encountered at any flying field. FD 2.4GHz V3 radio control system＇s features ◆Long range and more Stability ◆More small and more ultra light...
- Page 3 FD 2.4GHz V3 radio control system＇s details 1. FD 2.4GHz V3 radio control system consists of: Transmitter module （IS‐8F/IS‐8J） ×1 Receiver （IS‐8R /IS‐6R /IS‐4R/IS‐4R0） ×1 Transmitter antenna (IS‐TA) ×1 Voltage protector ×1 2. Transmitter module compatibility Futaba module（IS‐8F）： Futaba: 3PM/3PK/7U/8U/8J/9C/9Z/10C and FN series. Hitec: Optic 6/Eclipse 7. WFLY: WFT08/WFT 09. JR module（IS‐8J）: JR: 347/388/783/U8/PCM10/PCM10S/PCM10SX/ PCM10IIS/ 8103/3810/J9303/MX‐22/MX‐24S/PX/9X/9XII / Turnigy9X /11X 3. Transmitter module specifications Dimensions:58.5×37.5×22.1mm（IS‐8F） 63.9×48.5×36.5mm（IS‐8J） 40.2×20.1×7.2mm （IS‐8D） (DIY kit) ...
- Page 4 Follow these easy steps to set up your transmitter and receiver. Install the transmitter module and receiver 1. Remove the original transmitter module. 2. Put the FD 2.4GHz transmitter module into the module port and screw on the transmitter antenna. 3. When you do install the receiver in the model try to place the tip of the antenna (the silver bit(s) approx 33mm long) away from objects with ...
- Page 5 4. Check system operation. Turn the transmitter on. The module LED should be green. Connect the receiver to the battery. The red LED on the receiver will flash three times (now it is searching for the frequency) and light red, indicating the receiver is operating properly. The LED on the receiver will not light when there is no signal. Once the successful binding of Tx module and Receiver, no binding again in the following use. ...
- Page 6 Set Failsafe IS‐4R0 automaticly IS‐4R0 can set failsafe , when it lose control, all channels with no output. IS‐4R&IS‐6R & IS‐8R 1. After initial binding, turn on the transmitter. 2. Press and hold the button on the receiver. Connect the receiver to the battery. The LED on the receiver will light（about 1s） and then go out (for about 1s）. At this time (when the LED off) remove your hand from the receiver button. The LED on the receiver will then go on. 3. Move the joystick on your transmitter to where you want the surfaces / motor etc to be in the event of lost signal. Press the button on the receiver .The LED will flash several times; this shows the receiver has remembered the position which you have set. In the rare event that your ...
- Page 7 Range checking For safety, we suggest you conduct a range test before each flying session. 1). Have a friend hold the model for you. Position the model at least two feet (60cm) above non‐metal contaminated ground. If you don’t have anyone to help you, use something like a wooden bench. Make sure the model cannot move under its own power. 2). Press and hold on the “RANGE” button on the module and turn on the transmitter. （ please don’t release the button for the whole process）.The ...
- Page 8 Attach: Instruction of LED on the TX module Green LED light on Normal working Yellow LED stay on Short range testing LED flash between red and green Bind code Change TX module ID Flash red LED condition Enjoy your Fly-Dream 2.4GHz Radio Control System. ...