Page 2
– at any time and anywhere. Operation, mainte- nance or support of these targets become as easy as surfing the Web. The Aartesys EasyGateway® with C2C service is the ideal solution for remote control and remote maintenance in the machine-2-machine (m2m) environment.
Safety notes and technical specifications Safety notes This device must be operated as described in these operating instructions as otherwise the provided protection will no longer be ensured and the device may produce risks. Disconnect the system and the device from the power supply before you start working on it.
Page 5
Technical specifications Display elements 3 LEDs, bicolor red/green, for start-up and operation indicator 1 LED orange GSM status Communication Full Internet capability with certificate-based authentication and encryption LAN/WAN connection Fast Ethernet 10/100 Mbps, auto-MDIX, RJ45 shielded, 2 status LEDs Fiber optic connector 100 megabits FX, SC connector (single mode, dual or single fiber) Mobile communication GPRS (Quad Band GPRS class 10)
Installation The EasyGateway® is either snapped on a 35 mm DIN rail or mounted using screws. Wall mounting The EasyGateway® is mounted directly to the wall using the holes provided in the housing bottom and 2 x 3.5 mm screws. Use the distance of the holes in the housing bottom as reference.
Antenna & SIM card This step describes the mobile connection via GPRS/UMTS. Antenna connection If the EasyGateway® is operated via the air interface, i. e. GPRS/ UMTS, an antenna must be connected to the SMA antenna socket at the back of the unit. Use a spanner to fasten the antenna (approx.
Page 14
Step 3 The supply voltage for the EasyGateway is specified on the type plate. Supply voltages that do not conform to the specifi- cations indicated on the type plate may result in malfunction and destruction of the device. The connecting lines for the supply voltage must be secured via a UL listed fuse (6A type C) and must be provided with a disconnecting switch.
Power connection & terminal covers The EasyGateway® is connected directly to 85 to 264 V / 47 – 440 Hz AC voltage. Power connection 3 fully insulated spring-loaded terminals, wire or stranded wire up to 1.5 mm . Preferably use a size #0 screwdriver for operating the terminals.
Network RJ45 The EasyGateway® is provided with a Fast Ethernet interface for communication via wire-bound IP networks. Network The connection is via RJ45 jack with standard connector pin assignment and integrated LED display. The interface is designed as a so-called auto-MDIX interface, which means that straight and crossover Ethernet cables, shielded or unshielded, can be used.
Page 19
Operation & status display Once the voltage has been connected, the LEDs should have the following status: LED “GSM” (yellow) must be flashing when communication is realized via the mobile network. This LED is not lit if communication is realized via Ethernet interface. Local LED “Local”...
Page 20
Step 6 Setting the configuration on the Easy Gateway and start-up process For this step, use a 1 mm Allen wrench or a paper clip to push the reset and the start-up buttons. Setting the IP address of the Ethernet interface Mode: Configuration For setting the IP address of the Ethernet interface, first press the Reset button briefly, and then press and hold the Start-up...
Page 21
The configuration page Connect a PC with a normal LAN able to the EasyGateway (Ethernet interface Eth0, Nr. 6 page 8). - Open the configuration page with a browser on the address 10.10.10.10. Use the “Configuration” tab and login to the con- figuration as user: “user”...
Page 22
Testing the mobile communication reception level Mode: Start-up After configuration mode, the EasyGateway will start in start-up mode. The reception level is indicated by the 3 LEDs Local, Config and Network. LED “GSM” (yellow) must flash Local LED “Local” (red) reception level adequate / -80…-100 db Config LED “Config”...
Page 25
Other interfaces RS485 The RS485 interface allows for connection to serial terminal devices for C2C application 1 to 32 energy meters for metering applications. The interface operates exclusively in bus configuration. The software applications for the operation of the serial interfaces must be loaded on the EasyGateway.