Related Manuals for Charnwood BG6
Summary of Contents for Charnwood BG6
- Page 1 6” BENCH GRINDER OWNERS MANUAL MODEL: BG6 Charnwood Machinery Ltd, Cedar Court, Walker Road, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. -
Page 3: Specification
Overview of BG6 6” Bench Grinder Work Light Magnifying Guard Wheel Dresser Guard Grey Grinding Disc (Coarse) Work Table Wing Nut White Grinding Disc (Fine) On Off Switch Coolant Tray Work Table Specification Motor (Induction) 220v-240v, 50Hz 250w (0.33hp) Maximum Continuous Runtime S2... - Page 4 Unpacking All items are contained in one cardboard carton. Carefully unpack and check that all items are included as in the photograph. Assembly Attach part #8 left hand spark guard using the M4 x 10 pan head bolt, M4 locking washer and M4 washer. The gap between the grey grinding wheel and the bottom of the spark guard should not exceed 2mm.
- Page 5 Attach part #11 left hand guard arm using the M6 x 14mm Hex bolt and M6 Washer. Attach the Eye Guard Bracket onto the Eye Guard using the 2 x M3 screws and nuts. Slide the assembled part #30 eye guard onto part #11 left hand guard and tighten using the M6 nut.
- Page 6 Attach part #20 right hand guard arm using the M6 x 14mm Hex bolt and M6 Washer. Attach the Eye Guard Bracket onto the Eye Guard using the 2 x M3 screws and nuts. Slide the assembled part #63 magnifying eye guard onto part #20 right hand guard and tighten using the M6 nut.
-
Page 7: Using The Grinder
Using The Grinder To start the grinder, set the On/Off switch position to: 1 Wait for the motor to reach its maximum speed of rotation. Only then should you begin grinding. To stop the grinder, set the On/Off switch position to: 0 Be aware the motor will take some time to come to rest. -
Page 8: Maintenance
The machine includes an integral tray which should be half filled with water. If the ground edge turns bluish black it is overheating and should be regularly dipped into the cooling tray. The white stone wheel is a material designed to prevent heat building up and should be used whenever heat is an issue Maintenance... - Page 9 Inspect the new stone for cracks and damage to either the front face or the edges before fitting. Carefully slide the stone onto the shaft, replace the plate flange, the nut. Tighten against the rotation of the stone. CAUTION: Do not overtighten. TO REPLACE THE WHITE STONE Disconnect from the power source.
-
Page 10: Troubleshooting
Your local refuse amenity will have a separate collection area for EEE goods Declaration of Conformity for CE Marking Charnwood Declare that Bench Grinder, Model BG6 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EU And further conforms to the machinery example for which the EC type examination Certificate No. - Page 11 Charnwood BG6 Parts Drawing...
- Page 12 Washer Washer Screw Right Wheel Guard Right Spark Deflector Updated April 2019 Charnwood Machinery Ltd, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU, England Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...