Welcome Thank you for purchasing the UltraLite ALS®. Please take a moment to inspect the shipment to make sure the following parts are included with your Kit: Basic Kit (200-00110) Basic Plus Kit (200-00114) Complete Kit (200-00111) 1 UltraLite ALS®...
OPERATIONAL SAFETY The UltraLite ALS® incorporates solid-state emitters to generate the wavelengths required for quality forensic illumination. The output intensity of these components is strong enough to present the risk of injury to eye and skin tissue. DO NOT POINT THE UNIT...
ULTRALITE ALS® FEATURES UltraLite ALS® 1/4 - 20 Tripod Mount Low Battery Indicator Power Level Indicators On/Off Power Setting Button Button Battery Pack Charger Battery Docks Charger Power Indicator Charging Indicators Power Input Jack OPERATOR’S MANUAL...
Page 6
Head Assembly Battery Pack Power Adapter Pack LIGHT OUTPUT SPECIFICATIONS (mW) Head Designation 1/4 Power 1/2 Power 3/4 Power Full Power UV (400 nM) 1030 1550 2110 Green Yellow 1325 Infrared (IR) White 1275 ®...
OPERATING INSTRUCTIONS 1. UltraLite ALS® Assembly a.) Attach the desired Head Assembly to the UltraLite body. Insert the head in a straight and slow manner to avoid damaging the contact pins. Hold the head against the handle, and rotate the locking ring on the handle until it is hand-tight. DO NOT TWIST THE HEAD. DO NOT OVER TIGHTEN.
2. UltraLite ALS® Operation This unit features an energy conserving “sleep mode”. After five minutes of inactivity, the unit will automatically shut off the indicator lights and enter this mode. a.) If the unit is in sleep mode, press the On/Off button once to “wake up” the unit.
& and filters 6500 kalvin fingerprints 3. Disassembly a.) To remove the head, rotate the locking ring on the handle until the head becomes loose. Pull the head straight away from the handle. b.) To remove the power or battery pack, squeeze both tabs on the sides of the item, then pull straight out. Head When mounting the Head Assembly to the UltraLite ALS®, twist the Locking Ring only. DON’T TWIST THE HEAD! Locking Ring OPERATOR’S MANUAL...
BATTERY PACK CHARGER The battery pack charger features a logic circuit that will determine if a battery pack is in place and if it needs to be charged. If two battery packs are in pace and both need charging, the unit will fully charge both batteries simultaneously.
Clean the UltraLite® and its accessories using a soft cloth dampened with a mild detergent solution. Use a cotton ball or swab and a mild glass cleaner to remove dust and dirt from the Head Assembly lens. Avoid touching the lens. Do not drop or apply blunt force to the UltraLite or its accessories. Store the UltraLite components in the travel case provided when not in use. To extend the life of the battery remove the battery from the handle and replace it with the power pack adapter if the unit is not going to be used for several days.
TROUBLESHOOTING Problem Solution Unit does not activate. Make sure the power or battery pack is fully inserted. Make sure the battery pack is charged. Make sure the wall or car power supply is plugged in, and the jack is fully attached to the power adapter pack. Unit turns on, but no Press the trigger button light comes out.
TROUBLESHOOTING (CONT.) Light output is weak. to confirm the unit is (cont.) at the desired setting. Remove dust or other containments from the Head Assembly lens. OPERATING SPECIFICATIONS Power Input, car adapter: 12DC @ 2.5A Power Input, wall pack: 100-240VAC @ 50-60Hz Operating Temperature Range: -30° to +40°C LED Lifespan: ~ 5000 hours OPERATOR’S MANUAL...
The UltraLite ALS contains no user- serviceable parts. Any alteration, tampering, opening, or abuse of the UltraLite ALS voids the warranty. The CAO Group may repair or replace products eligible for the warranty at its option. Please contact an authorized UltraLite ALS representative for warranty questions.