Parameter Setting - Westpow STR.B Series User Manual

User Manual User Manual

Parameter setting

Parameter setting
9 9
9.1 Starting mode 9.1 Starting mode
On Ready state On Ready state , press , press key and release it 5 minutes later ( or key and release it 5 minutes later ( or
press press and and key at the same time), system enter the Starting mode key at the same time), system enter the Starting mode
selecting state selecting state . . Then press Then press
to set the to set the Starting Mode Code . If Starting Mode Code . If
top-left of the keyboard top-left of the keyboard Voltage Ramp Voltage Ramp
Voltage Ramp. If Voltage Ramp. If 2 2 is selected, the lamp is selected, the lamp
keyboard keyboard Current Limit Current Limit is light, the Starting mode is Current Limit. is light, the Starting mode is Current Limit.
If If 3 3 is selected, the Starting Mode is Jogging. Any lamp on the left of is selected, the Starting Mode is Jogging. Any lamp on the left of
keyboard is not light. After the starting mode parameter is selected, press keyboard is not light. After the starting mode parameter is selected, press
key, other parameter related to the selected Starting mode can be key, other parameter related to the selected Starting mode can be
modified. modified.
For Example: For Example:
Starting mode Starting mode
Press Press
(maintain 5 second) (maintain 5 second)
Or press Or press
Figure 9-1
Note: Note:
User can select the Starting mode according to the load type. For the normal load, User can select the Starting mode according to the load type. For the normal load,
any of two modes can be adopted. But for big inertia load type, the Voltage Ramp any of two modes can be adopted. But for big inertia load type, the Voltage Ramp
mode is the best choice. The default value is mode is the best choice. The default value is
OPERATION 18
MENU
or or key to modify the parameter key to modify the parameter
1 1 is selected, the lamp is selected, the lamp on the on the
is light is light , the Starting mode is , the Starting mode is
on the top-left of the on the top-left of the
Voltage Ramp Voltage Ramp
press press or or
Current Limit Current Limit
Jogging Jogging
, that is Voltage Ramp mode. , that is Voltage Ramp mode.
9.2 (Voltage Ramp mode) Setting and Inquiry 9.2 (Voltage Ramp mode) Setting and Inquiry
If the Voltage Ramp mode is selected, the flow chart of the related If the Voltage Ramp mode is selected, the flow chart of the related
parameters setting is show in figure 9-2 parameters setting is show in figure 9-2
Voltage Ramp mode Voltage Ramp mode
Press Press
Initial voltage of ramp Initial voltage of ramp
Press Press
Start time of ramp Start time of ramp
Press Press
Over current protect value Over current protect value
Press Press
Current unbalance factor Current unbalance factor
Press Press
Control mode select Control mode select
Press Press
SCR trigger select SCR trigger select
Press Press
Start overload level Start overload level
Press Press
Over current protect at running Over current protect at running
Press Press
Stop mode selec Stop mode selec
Press Press
Soft stop Soft stop
factor factor
Figure 9-2
Note: Note:
1. When any of one parameter is modified, press whether 1. When any of one parameter is modified, press whether
or or key( return Ready state key( return Ready state
automatic. automatic.
2. When modify any of the parameter, press 2. When modify any of the parameter, press
User Manual User Manual
Press Press or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
or or
to modify to modify
Press Press
key (change page) key (change page)
), the modified parameters will be saved ), the modified parameters will be saved
key to return the Ready state key to return the Ready state
OPERATION
MENU
19