Subscribe to Our Youtube Channel
Related Manuals for Industrial Scientific Ventis 17154524-1
Summary of Contents for Industrial Scientific Ventis 17154524-1
- Page 1 Field Guide Setup, Operation, and Service Edition May 14, 2018 Part Number: 17154524-1...
- Page 2 Industrial Scientific Corporation, Pittsburgh, PA USA Industrial Scientific Co., Ltd. Shanghai, China © 2016, 2017, 2018 Industrial Scientific Corporation All rights reserved. Published 2018. Revision 10 www.indsci.com/ventis/vsp...
-
Page 3: Table Of Contents
Contents Tables and Figures ........................iii General Information ........................... 1 Guidelines for using a motorized pump and sampling line ............3 Product overview ........................4 Installation ..............................4 Power source ............................4 Sample draw ............................. 4 Hardware overview ........................7 Setup, Operation, and Service .................... -
Page 5: General Information
General Information Each Ventis Slide-on Pump is certified by one or more certifying bodies (CBs). Certifications for the Ventis™ Slide-on Pump, at the time of this document's publication, are listed below in Table 1. To determine the hazardous-area classifications for which a pump is certified, refer to its label or the product order. - Page 6 Table 1.2 Warnings and cautionary statements Read and understand the manual before use. Failure to perform certain procedures or note certain conditions may impair the performance of this product. When sample tubing is connected to the pump and the pump is powered on, it continues to draw sample air even if the pump door is open.
-
Page 7: Guidelines For Using A Motorized Pump And Sampling Line
Guidelines for using a motorized pump and sampling line When sampling with a motorized pump and sampling line, Industrial Scientific recommends the following: • Choose the tubing type based on the target gases. If the target gases are known, use Teflon-lined... -
Page 8: Product Overview
Product overview The Ventis Slide-on Pump is an in-field attachable and in-field removable pump. This enables the use of a single compatible instrumet for both personal monitoring (diffusion) and confined space applications (aspirated). Installation The pump’s spring-assisted, hinged door is opened and secured closed by the body-mounted latch; therefore, no tools are needed for instrument installation or removal. - Page 9 Table 1.4 Compatibilities Item Part number Item Notes Instruments Varies Ventis Pro Series, Ventis MX4 Diffusion unit only Use of the VSP may result in sensor readings that are within ± 5% of their published accuracy specifications; sensor T90 response times may increase by 10 seconds.
-
Page 11: Hardware Overview
Hardware overview Feature Feature Part number — Power-on and -off button Visual alarm (pump) Inlet cap and tubing nipple 17129909 Audible alarm (with filter) 17154581-5 (filter) 90dB (typical) Water barrier (inside inlet 17152395 barrel; not shown) Power status indicator Battery status indicator and —... -
Page 12: Instrument Installation And Removal
Tip. The battery charge indicators are: Solid green indicates charging is complete. • Blinking green indicates charging is in progress. • Blinking amber indicates a charge fault. • Charge the pump in a compatible charger (single-unit charger shown). The pump’s orientation is contact-side down so its battery contacts touch the charger’s contact pins. -
Page 13: Pump Test And Operation
Pump test and operation 4. Use a thumb to block the end of the sampling line at 1. Power on the pump: press and hold the power button the water-stop opening. This should cause a pump- for three seconds. The pump will emit a series of audio fault alarm. -
Page 14: Service
Service Door Installation and removal Battery Top peg to hinge Spring coil Bottom peg to hinge Power off the pump. A wire extends from the spring coil WARNING: This task must be completed in an located inside the covered hinge. To area known to be nonhazardous. -
Page 15: Alarms
Alarms The following table describes the types of alarms that may occur when using the pump. Indicators, possible causes, and recommended actions are described for each alarm type. For additional assistance in resolving any alarm condition, see an on-site supervisor or contact ISC Technical Support (see “Contact Information”). -
Page 16: Warranty
(including negligence), strict liability, products liability or any other theory of liability, will be limited to the lesser of Buyer’s actual damages or the price paid to Industrial Scientific for the Products that are the subject of Buyer’s claim. All claims against Industrial Scientific must be brought within one year after the cause of action arises, and Buyer expressly waives any longer statute of limitations. -
Page 17: Contact Information
E-mail： info@ap.indsci.com 网址： www.indsci.com 服务热线：+86 400 820 2515 To locate a nearby distributor of our products or an Industrial Scientific service center or business office, visit us at www.indsci.com. Rendez-vous sur notre site Web www.indsci.com, si vous voulez trouver un distributeur de nos produits près de chez vous, ou, si vous recherchez un...
Need help?
Do you have a question about the Ventis 17154524-1 and is the answer not in the manual?
Questions and answers