Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Samcon ExCam XF Q1785
- Page 1 ExCam ® XF Q1785 User Manual...
-
Page 2: Table Of Contents
Table of Contents Introduction ......................4 Technical data ......................4 Explosion protection .................... 4 Electrical parameters of the camera ..............5 Connection cable Ex-d - Ex-e (ASKDP03-T) ............5 Video-technical characteristics ................6 Other technical data .................... 6 Safety Instructions ....................7 Installation ........................ - Page 3 Fig. 6-1 Removing the weather protection roof (1/2) (this illustration is an example) ..22 Fig. 6-2 Removing the weather protection roof (2/2) (similar illustration) ......23 Fig. 6-3 Opening the ExCam XF Q1785 (similar illustration) ........... 23 Fig. 6-4 Reset Button ....................... 25 Fig.
-
Page 4: Introduction
1, 2, 21 and 22 including the explosion groups IIC / IIIC. To see other approv- als, please visit our website at www.samcon.eu When designing the ExCam XF Q1785, we attached a very high importance to safety, mechanical precision and high quality of stainless steel. Technical data... -
Page 5: Electrical Parameters Of The Camera
Data line: 4 x 2 x AWG22/1 CAT.6a Performance elements: 3G1.5 (BK-BU-GN/YE) Properties: halogen-free, flame-retardant, resistant, chemical resistance, shielded (see www.samcon.eu Quick link: https://www.samcon.eu/fileadmin/documents/en/60-Assembling%26mounting/ASKDP03-T_Datasheet.pdf Fig. 2-1 Sectional view of the ASKDP03-T Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 5 of 32... -
Page 6: Video-Technical Characteristics
Video-technical characteristics We use the AXIS Q1785 Network Camera in a pressure-resistant enclosure. For details, ® please refer to the Product Documentation, video-technical data of AXIS https://www.axis.com/products/axis-q1785-le Other technical data Camera (Ex-d) Terminal box (Ex-e) 0°C … +60°C -60°C … +55°C Permissible ambient temperature (for PoE power supply) -60°C …... -
Page 7: Safety Instructions
. When installing the ExCam, adhere to the requirements of the EN/IEC 60079-14. ExCam XF Q1785 is only suitable for installation sites with a low risk of mechanical hazard. Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 7 of 32... -
Page 8: Installation
Installation For erecting and operating the camera, the relevant national regulations, as well as the generally accepted rules of technology shall prevail. Before mounting the camera, thor- oughly check it for any transport damage, especially regarding the housing and the cable. Installation, electrical connection and the commissioning must only be carried out by qualified specialists. -
Page 9: Tab. 4-1 Mounting Accessories
In case of doubt, take appropriate security measures. Drawings for drilling hole patterns and further information can be viewed on our product page: Quick link: https://www.samcon.eu/en/products/network/excam-xf-q1785/ Option mounting accessories WALL MOUNT EXCAM XF (01569-001) Wall bracket Wall bracket for devices of T08-VA3 series. -
Page 10: Electrical Connection
NOT authorised to do electrical connection procedures inside the pressure-resistant enclosure. Potential equalization Fig. 5-1 ExCam XF Q1785 potential equalization The potential equalization/grounding of the camera body is absolutely necessary, in order to avoid static charges and thus the formation of sparks. For this purpose, a screw termi- nal is provided at the rear side, at the bottom (right) (see Figure 5-1). -
Page 11: Connection Work At The Device (Terminal Box) And Fuse Protection
Wiring table: Potential Colour (IEC 60757) Cross- Comment section GN/YE 4 mm (rigid) Terminal: Slotted screw M4x0.7 (DIN 84) with washer Ø9mm (DIN 125A), Keep 3 Nm tightening torque! Tab. 5-1 Equipotential Bonding Connection work at the device (terminal box) and fuse protection Supply of 24 V DC for the heating and wiper Power supply: 22 V DC <... -
Page 12: Fig. 5-2 Camera (Ex-D) And Terminal Box (Ex-E)
Fig. 5-2 Camera (Ex-d) and terminal box (Ex-e) Video Tutorial: Please view our video tutorial: “SAMCON 01 Wiring the cable SKDP03-T to the junction box ExTB-3” https://go.samcon.eu/v01 Fig. 5-3 Video Tutorial ExTB-3: Screw on the terminal box ExTB-3 Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 12 of 32... -
Page 13: Tab. 5-2. Wire Assignment Of Terminal Box Extb-3
The pin assignment of the ASKDP03-T is executed in accordance with the standard EIA/TIA-568B for 100BaseTX and 24VDC, as follows: Camera (Ex-d) Colour Terminal Cross- Comment ASKDP03-T ExTB-3 sectional (T568B) (IEC60757) surface Reinforcement YE / GN 2.5 mm Flex WH / OG 0.32 mm Solid conductor 0.32 mm... -
Page 14: Fig. 5-5 Photo Of The Occupied Terminal Box Extb-3
Bring the twisted pair composite approximately 10mm close to the terminals, in order to ensure the interference immunity. Attention! Use only terminals approved by SAMCON. Attention! Finally, check your network installation by per Class-D Link Test. Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 14 of 32... -
Page 15: External Connection And Protection
External connection and protection There are several options of routing the ExTB-3 terminal box in a safe area: 5.3.1 Direct routing from the ExTB-3 into the safe area Switch/ 24 V DC for heating unit and wiper PoE (802.3at) for camera Fig 5-6 ExTB-3 ->... -
Page 16: Routing Via Exconnection Rail (Optional Accessories)
5.3.2 Routing via ExConnection Rail (optional accessories) Fig. 5-7 ExTB-3 -> ExConnection Rail In case of routing the ExTB-3 into an ExConnection Rail, larger installation distances can be covered. Note: In hazardous areas, the ExConnection Rail (optional accessories) acts as a PoE+ switch, a media converter from copper to fibre-optic cable, as well as a power supply for the cameras. -
Page 17: Fig. 5-8 Barrier Gland
We show the basic procedures in the following video tutorial: Video Tutorial: Observe our video tutorial: “SAMCON 02 Mounting and installing Ex-d barrier glands to ExConnection Rails” https://go.samcon.eu/v02 Fig. 5-8 Barrier gland Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 17 of 32... -
Page 18: Cable Kits - "Plug And Play" Connection Packages
5.3.4 Cable kits - "plug and play" connection packages There are various cable kits for different cables and in different lengths available. The connection packages include everything you need for a professional system installation: 10/25/95 m ASKDP03-T sys- tem cable, digital (a) ... -
Page 19: Fusing
SKDP03-T CABLE EXCAM 25M ASKDP03-T CABLE EXCAM 25M 25 meters (01541-001) (01545-001) This cable set includes: This cable set includes: 25 meters SKDP03-T system cable, digital 25 meters ASKDP03-T system cable, digital 1 x barrier gland Ex-d 1 x bolted connection Ex-d 5 ml Loctite 243screw locking 1 x bolted connection Ex-e 1 x CAT6 RJ45 industrial plug... -
Page 20: Plug Assignment (Rj45)
5.3.6 Plug assignment (RJ45) The data transfer of the ExCam XF Q1785 series uses a 100 Mbit/s Ethernet connection (100BASE-TX). If the cable termination uses a plug, the latter should be plugged into the RJ45 PoE slot of the network device (PSE). Prior to connecting it to the camera, the network device (PSE) can already be supplied with power, hence there is no „power ON“... -
Page 21: Tests Prior To Switching On Voltage
5.3.7 Tests prior to switching on voltage Attention! Prior to starting the device, perform all tests as indicated by the na- tional regulations. Furthermore, check the correct function and instal- lation of the device in accordance with this user manual and other ap- plicable regulations. -
Page 22: Opening The Pressure-Resistant Housing
Make sure that the wiper in placed in the central position! ExCam XF Q1785 is equipped with a weather protection roof. Prior to starting you work, the roof shall be removed. To do so, loosen the 4x8mm lens screws M4*0.7 at the front and rear sides of the bracket holders (Figure 6-1). -
Page 23: Fig. 6-2 Removing The Weather Protection Roof (2/2) (Similar Illustration)
Fig. 6-2 Removing the weather protection roof (2/2) (similar illustration) To open the stainless steel housing (T07 VA2.3.x.x) of the ExCam XF Q1785, loosen the eight cylinder-head hexagon screws (DIN 912/ ISO 4762) together with their spring rings (DIN 127A) on the rear side of the cable and power supply flange (see Figure 6-3). Cau- tion: do not touch the screw threads with your skin or clothes! On the threads, there is LOCTITE®... -
Page 24: Removing/Inserting An Sd Memory Card
Removing/inserting an SD memory card Note: The ExCam XF Q1785 has a slot for a micro SDHC memory card. Saved video files can be played and deleted via the web interface. They are also available in a download list. Moreover, the videos available in the memory card can also be accessed via FTP server in the network. -
Page 25: Hardware Reset
Hardware Reset To re-set all parameters of the ExCam XF Q1785 (including the IP address) to default setting, a hardware reset has to be carried out. The parameters can be reset via the web interface or manually. If within the network, the camera can no longer be reached or if it is in an uncontrollable state, the reset should be performed manually. -
Page 26: Battery
- crosswise and evenly! Battery ExCam XF Q1785 is equipped with a high-temperature resistant Panasonic button cell BR2330A/VAN. This cell supplies energy to the internal real time clock (RTC). The cus- tomer is not allowed to replace the battery! In this case, please contact the manufacturer. -
Page 27: Network Access And Visualization
Interface, please see the Axis User Manual or visit the following website: https://www.axis.com/products/axis-q1785-le The delivered ExCam XF Q1785 is set to the applicable net frequency (50Hz or 60Hz). If the camera is used at a location with a differing net frequency, a flickering of the picture might be noticeable, particularly in surroundings with fluorescent tubes. -
Page 28: Password/ Identification
How to start the wiper The ExCam XF Q1785 is equipped with a wiper. The wiper can be started via a button in the lower right corner of the web interface (see Figure 7-2). Fig. 7-2 User Interface to operate the wiper... -
Page 29: Maintenance/ Modification
Repair and correction Repairs may only be carried out with original parts of SAMCON Prozessleittechnik GmbH. Damaged pressure-resistant housings have to be replaced completely. If in doubt, send the part in question back to SAMCON Prozessleittechnik GmbH. -
Page 30: Replacement Of The Wiper Lip
This Document is subject to alterations and additions. Drawings & 3D models All drawings, 3D models, certificates and other information are available in the download area of the product page on our website: https://www.samcon.eu/en/products/network/excam-xf-q1785/ Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 30 of 32... -
Page 31: Certificates And Further Documentation
If you wish additional technical information, please contact us at: support@samcon.eu Certificates and further documentation Certificates and further documentation are available in the download area at the product website: https://www.samcon.eu/en/products/network/excam-xf-q1785/ Doc.-ID: 190402-PT08BA-ES-ExCam XF-Q1785_EN_rev.00.docx, Page 31 of 32... - Page 32 Schillerstrasse 17, 35102 Lohra-Altenvers, Germany www.samcon.eu, info@samcon.eu Phone: +49 6426 9231-0, fax: - 31...
Need help?
Do you have a question about the ExCam XF Q1785 and is the answer not in the manual?
Questions and answers