Advertisement
Quick Links
Advertisement
Summary of Contents for XDOM PRO ZERO
- Page 1 XDOM User Manual...
- Page 2 Intro Dear Customer, Thanks for choosing XDOM® PRO. This user manual in- cludes important information regarding security and prop- er installation of XDOM® PRO devices. The package includes: - n.1 module (also called “device”) XDOM® PRO - n.2 supporting screws...
- Page 3 XDOM® PRO is a smart wifi switch, implementing remote monitoring and control features in simple and efficient man- ner. XDOM® PRO are designed to continuously operate at the best performances. The devices are the input/output elements of the smart network, interacting with a Cloud system and available to the user operations via an app for smartphone/tablet.
- Page 4 Pre- requirements The XDOM® PRO have been design to remotely operate via Wi-fi connection. In case of connectivity loss, the modules are still available through local and manual commands. Therefore, before XDOM® PRO installation it is highly recom- mended to verify the availability of a stable Wi-fi network.
- Page 5 XDOM® PRO can be installed even in pres- ence of lighting phenomena, due to adequate design able to prevent damages to the module.
- Page 6 As mere example, it is explicitly forbidden to install XDOM® PRO to control plants in close proximity of fuel deposit, ammos, gas refinement plants. In any case, the XDOM® PRO installation shall be not able to by-pass the emergency control mechanism of the destination plant.
- Page 7 Description of XDOM® PRO XDOM® PRO is available in a plastic package, with tem- pered glass front panel, suitable to be installed within an Italian electrical box 503E, but also within generic electri- cal boxes of suitable dimensions. XDOM® PRO does not contains other parts available to direct usage from the cus- tomer.
- Page 8 (e.g. within the electrical motors boxes) TYPICAL USE SCENARIO XDOM® PRO ZERO can be used to generate the pulse con- trol signal for an electrical gate, therefore replicating a nor- mal remote. An external relay is typically required, to be installed within the electrical motor box, where also the XDOM®...
- Page 9 XDOM® PRO ONE one touch button. The single output channel is controlled in ON/OFF via this button and the XDOM® PRO app. It is suitable for the remote control of a single electrical equip- ment, even if power demanding (e.g. industrial machines) via an additional external relay.
- Page 10 ON/OFF of illumination of the same environment). TYPICAL USE SCENARIO XDOM® PRO TWO can be fruitfully used to control shutters. Each XDOM® PRO output line can control one of the two ro- tating senses, up to the full opening/closure of the shutter.
- Page 11 ON/OFF of illumination of the same environment).via an additional external relay. TYPICAL USE SCENARIO XDOM® PRO THREE can control three ceiling or wall lights. XDOM® PRO is tailored for the installation within Ital- ian 503E box, or in any suitable box.
-
Page 12: General View
General view XDOM® PRO is provided with an electrical connection breakout, located on the module rear side, available for the Line (L), Ground (N), and Output (L1, optionally L2, optionally L3) connections. L3 L2 Electrical supply 230 VAC - 50 Hz... -
Page 13: Installation
Input power stage is protected with a non-replaceable fuse. In case of fuse intervention, the XDOM® PRO device shall be replaced. Output lines not galvanically isolated, therefore the elec- trical connection shall be strictly performed referring to the schematics outlined in this document. - Page 14 N.b. to provide Cloud communication, XDOM® PRO shall be installed in areas with sufficient preferred Wi-Fi network (e.g. home or office) availability. Dif- ferently, XDOM® PRO features are not guaranteed. To increase the service reliability, Wi-Fi repeaters use is suggested, while mobile hotspots (i.e. equipped with SIM cards) is suggested in case of complete not avail- ability of Wi-Fi signal for extreme conditions.
-
Page 15: Normal Installation
NORMAL INSTALLATION (< 2A of absorbed current for output line) L3 L2 RELAY INSTALLATION (> 2A of absorbed current for output line) L3 L2 COIL...