Table of Contents
Advertisement
Quick Links
Instruction Sheet
CWR SERIES
CABLESAFE
TM
WALL CABINET
U L
C
US
R
LISTED
CABLESAFE WALL CABINET WITH
CABLESAFE WALL CABINET WITH
STANDARD DOOR
4" DEEP DOOR
THANK YOU
Thank you for purchasing the CWR Series CableSafe Cabling Wall Cabinet. Please read these
i nstructions thoroughly before installing/assembling this product.
PRODUCT FEATURES
- 26" width provides abundant space for patching
- Ships with front rackrail at a 4" setback to accomodate cable managers
- Swing open center section allows for easy front and rear access to equipment and cabling
- Available with vented, plexiglass or solid doors
I-00347
Rev B
Advertisement
Table of Contents
Summary of Contents for Middle Atlantic Products Cablesafe CWR Series
- Page 1 Instruction Sheet CWR SERIES CABLESAFE WALL CABINET LISTED CABLESAFE WALL CABINET WITH CABLESAFE WALL CABINET WITH STANDARD DOOR 4” DEEP DOOR THANK YOU Thank you for purchasing the CWR Series CableSafe Cabling Wall Cabinet. Please read these i nstructions thoroughly before installing/assembling this product. PRODUCT FEATURES - 26”...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS • Read these instructions. WARNING: A WARNING ALERTS YOU TO A SITUATION THAT COULD RESULT IN SERIOUS PERSONAL INJURY • Keep these instructions. OR DEATH. • Heed all warnings. CAUTION: A CAUTION ALERTS YOU TO A SITUATION THAT MAY RESULT IN MINOR PERSONAL INJURY OR •... -
Page 3: Cabinet Installation
CABINET INSTALLATION THE CABINET MUST BE INSTALLED PLUMB AND LEVEL FOR PROPER OPERATION. 1) Separate backpan from center section and determine hinge side. NOTE: CWR center section can be opened from left-to-right or vice versa depending on how backpan is installed. NOTE: Ensure the wall to which the backpan will be mounted, consists of two (2) 3/4"... -
Page 4: Grounding And Bonding
GROUNDING AND BONDING Protective Earth Terminals (PET) are located in backpan of the wall rack. These terminals are marked with the symbol Wall rack parts, center section and door, contain or are provided with bonding points for connection to the backpan / PET. Protective earth and bonding connections shall be in accordance with Article 250 of the National Electric Code. -
Page 5: Side View
GROUNDING AND BONDING (Continued) 1) Attach backpan bonding wire from 1/4”-20 backpan protective earth terminal (PET) to nearest center section bonding stud (10-32) using hardware provided. (FIGURE G) NOTE: The main protective earth ground needs to be the first terminal placed on the PET and this terminal needs to be secured on its own with a nut. - Page 6 D-RING INSTALLATION 1) Install the supplied D-Rings to the pre-installed rackrail on both sides of the rack as shown with the supplied hardware. (FIGURE B) 8-32 STUD 8-32 ACORN D-RING RACKRAIL FIGURE B STANDARD DOOR SWING REVERSAL 1) Remove the two (2) 10-32 screws from both top and bottom hinges to remove the door (remove 4 screws total). (FIGURE C) 2) Reverse the door to install to the opposite side of the rack.
- Page 7 4” DEEP DOOR SWING REVERSAL 1) Remove the 1/4-20 panhead screws and flange nuts from the top and bottom hinges to remove the door. (FIGURE D) FLANGE NUT HINGE 1/4-20 PANHEAD SCREWS FIGURE D 2) Remove the extended latch by removing the (2) two 10-32 screws. Install the latch to the opposite side of the rack.
- Page 8 4” DEEP DOOR SWING REVERSAL (Continued) 3) Reverse the door to install it to the opposite side of the rack using (2) two 1/4-20 panhead screws and (2) two 1/4-20 flange nuts per hinge (top and bottom). (FIGURE F) FLANGE NUT 1/4-20 PANHEAD HINGE...
-
Page 9: Warranty
WARRANTY Middle Atlantic Products (the "Company") warrants the CWR Series Cabling Wall Rack to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product. The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and...