jablotron JA-80IR Prelimenary Manual

The JA-80IR optical barrier is designed for the indication of a breach into
a certain area by crossing the IR line between the transmitter and the
receiver. The barrier is a product by Optex supplemented with
transmitters compatible with OASiS systems, this being both in the
transmitting and receiving part of the barrier. The device power supply is
ensured by high-capacity lithium batteries. The signal indicating that a
transmitter and receiver battery is low is transmitted to the ESS control
panel as standard. The barrier occupies two enrollment positions in the
system. Barrier activation is reported by the receiving part (the position
where its transmitter is enrolled in the system). Both parts of the barrier
can send a tamper signal to the control panel. The transmitters regularly
perform automatic tests and report their status via control transmissions
to the system.
Barrier installation
The following instructions should be observed when selecting a place for
barrier installation:
• Both units must be installed onto a stationary construction (e.g. a wall or a
thick post) at the same height and should face each other.
• The area between the barrier units must not be blocked by any bushes or
tall grass.
• There can be up to a 60 m distance between the units.
• The receiver unit must not be affected by direct sunlight.
•
The units should be installed 0.7 – 1 m above the ground.
• If the IR beam is parallel to a wall, there must be at least a 1 m distance
between the beam and the wall.
• If multiple barriers are used, their IR beams should not interfere with each
other.
Fig. 1 Undesirable locations
Installation steps:
The transmitting unit (marked TRANSMITER) and the receiving unit (marked
RECEIVER) are of identical mechanical construction.
Kryt Optická část
Šroub krytu
Fig 2 Barrier parts (identical for transmitter and receiver)
1. Unscrew the rear part screws and remove the unit bases.
2. Install the bases onto the selected places, either directly on a surface
(wall) – in such a case punch two holes through the base – or onto a post
53 – 58 mm in diameter using the supplied clips. When installing the unit
onto a post, use the supports and clips.
3.
When installing the base, always check whether the rubber tamper contact
pin is functional.
Prelimenary Manual (subject to change) - JA-80IR wireless optical barrier 1 /1
JA-80IR wireless optical barrier
Zadní díl Základna
Šroub zadního dílu
Šrouby
Výztuhy
M3 x 8
Fig. 3 Preparation for installation onto a post
4. Enroll the transmitters into the system – see below.
5. Perform optical adjustment and unit transmitter setting
6. Screw the upper covers back in and test the barrier functioning.
Enrolling the barrier transmitters into the system
The signal transmitters for wireless communication are located in the
rear part underneath the optical section. The barrier occupies two
enrollment positions in the system. Barrier activation is reported by the
receiving part (the position where its transmitter is assigned in the
system). Both parts of the barrier can send a tamper signal to the control
panel.
Always use two SAFT LSH20 lithium batteries to power the barriers
(they are included in the package). The correct position of the batteries
is indicated on the battery holder. The batteries should be inserted very
carefully to avoid damage to the transmitter wiring. When the first
battery has been installed, the transmitter sends a signal which enrolls it
to the control panel (the control panel must be in enrollment mode at
that time – see the manual). Use switch no. 2 to set the required system
reaction to movement (ON = instant or OFF = delayed). Switch no. 1
should be left in the OFF position
spínač 1
PULSNÍ*
STAVOVÁ
Vcc
spínač 2
TMP
ZPOŽDĚNÁ INP
GND
OKAMŽITÁ
* nastavte
pulsní režim
propojení
s detektorem
Fig 4 Radio transmitter (identical for transmitter and receiver)
Setting up the optical part of the barrier
The optical part of the barrier must be adjusted so that the optical parts
facing each other are physically aligned. Both units are equipped with
adjusting elements for the adjustment of direction and a view-finder for
precise adjustment. The unit opposite the one you want to adjust must be in
the centre of the aiming cross and the cross must be in the centre of the
view-finder.
hledá ek
průhled hledá kem
Prorazte otvory
Šrouby
M4 x 30
.
konektor pro
zadní tamper
baterie není
použita
signálka
č
špatně
správně
č
Třmen
M