1. Manuals
  2. Brands
  3. Sony Manuals
  4. Monitor
  5. Trinitron CPD-200GS
  6. Service manual

Sony TRINITRON CPD-200GS Service Manual

Color computer display
Hide thumbs Also See for TRINITRON CPD-200GS:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL

MICROFILM
SPECIFICATIONS
Picture tube
Viewable image size
Resolution
Standard image area
Deflection frequency
Audio output
Headphones jack
AUDIO IN jack
AC input voltage/current
Power consumption
Dimensions
Mass
Supplied accessories
Design and specifications are subject to change without
notice.
TRINITRON
®
CPD-200GS
Australian Model
Chinese Model
0.25 mm aperture grille pitch
17 inches measured diagonally
90-degree deflection
Approx. 327 243 mm (w/h)
(12
7
/
9
5
/
inches)
8
8
16.0" viewing image
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 312 234 mm (w/h)
(12
3
/
9
1
/
inches)
8
4
or
Approx. 293 234 mm (w/h)
5
1
(11
/
9
/
inches)
8
4
Horizontal: 30 to 85 kHz
Vertical: 50 to 120 Hz
0.5W (mono)
Stereo minijack
Accepts impedance of 8
or more
Stereo minijack
100 to 240 V, 50 – 60 Hz, 1.9 – 1.1 A
Max. 120 W
406 432 420 mm (w/h/d)
(16 17
1
/
16
5
/
inches)
8
8
Approx. 18 kg (39 lb 11 oz)
See page 6
COLOR COMPUTER DISPLAY
Chassis No. SCC-L07A-A
D-1H
CHASSIS

Advertisement

Table of Contents
loading

Related Manuals for Sony TRINITRON CPD-200GS

Summary of Contents for Sony TRINITRON CPD-200GS

  • Page 1: Service Manual

    SERVICE MANUAL Picture tube Viewable image size Resolution Standard image area Deflection frequency Audio output Headphones jack AUDIO IN jack AC input voltage/current Power consumption Dimensions Mass Supplied accessories Design and specifications are subject to change without notice. TRINITRON MICROFILM CPD-200GS Australian Model Chinese Model...

  • Page 2: Power Saving Function

    Contact your 15 sec. computer’s manufacturer. — If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition. MODE 2 MODE 3 MODE 4...

  • Page 3: Table Of Contents

    ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL.

  • Page 4: General

    The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. Getting started Getting Started Warning on power connection Precautions • Use an appropriate power cord for your local power Installation supply.
  • Page 5 Getting Started About the supplied Macintosh adapter Setup The supplied Macintosh adapter is compatible with Macintosh LC, Performa, Quadra and Power Macintosh series computers. Macintosh II series and some older versions of Power Book models Before using this monitor, check that the following items are may need an adapter with micro switches (not supplied).
  • Page 6 Customizing Your Monitor Customizing Your Monitor Before adjusting Introducing the On-screen • Connect the monitor and the computer, and turn them on. • Select “ (LANGUAGE)” in the OPTION OSD, then Display System select “ENG” (English) (see page 15). Most adjustments are made using the MENU OSD. Adjusting the Picture Brightness MENU OSD and Contrast...
  • Page 7 Customizing Your Monitor Press the >?// buttons to adjust the settings. Using the GEOM (Geometry) On- screen Display The GEOM (geometry) settings allow you to adjust the shape and orientation of the picture. Once the rotation is adjusted, it will be stored in memory for all input signals received.
  • Page 8 Customizing Your Monitor Press the ¨./> buttons to select the color Using the SCREEN On-screen temperature. Display Adjust convergence settings to eliminate red or blue shadows that may appear around objects on the screen. Adjust the CANCEL MOIRE function to eliminate wavy or There are two color temperature modes in the OSD.
  • Page 9 Customizing Your Monitor Changing the on-screen display position Locking the controls You can change the OSD position (for example, when you The control lock function disables all of the buttons on the want to adjust the picture behind the OSD). front panel except the u (power) switch and MENU button.
  • Page 10 Technical Features Customizing Your Monitor Selecting the Graphic Picture Preset and User Modes Enhancement (GPE) Mode The monitor has factory preset modes for the 9 (CPD- 100GS) or 10 (CPD-200GS) most popular industry standards The Graphic Picture Enhancement (GPE) button allows you for true “plug and play”...
  • Page 11 This is not a malfunction. • If the problem persists, call your authorized Sony dealer from a location near your monitor. • Note the model name and the serial number of your monitor. Also note the make and name of your video board.

  • Page 12: Disassembly

    CPD-200GS 2-1. CABINET REMOVAL Two claws PUSH Cabinet Two audio jacks Caution: To avoid breakage, gently pull sides of cabinet out and over the audio jacks when removing cabinet from Two screws (+BVTP 4 x 16) chassis. 2-3. D, A AND J BOARDS REMOVAL SECTION 2 DISASSEMBLY 2-2.

  • Page 13: Picture Tube Removal

    2-4. PICTURE TUBE REMOVAL • Remove the D, A and J boards (Refer to 2-3.) Four screws (Tapping screw 5) Picture tube shield Anode cup • REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.

  • Page 14: Safety Related Adjustment

    CPD-200GS When replacing parts shown in the table below, the follow- ing operational chacks must be performed as a safety pre- caution against X-ray emissions from the unit. D BOARD Part Replaced ( RV501 (HV ADJ) Part Replaced ( IC501, IC605, IC901, D517, C535, C540, C541, C542, C544, C553, C554, C555, C558, C561, R545, R546, R547, R548, R549, R550, R552, R564, R567, RV501, T501 (FBT)

  • Page 15: Adjustments

    Landing Rough Adjustment 1. Enter the full white signal. 2. Set the contrast to “CONT”=255. 3. Make the screen monogreen. Note: Off the outputs from R ch and B ch of SG. 4. Reverse the DY, and adjust coarsely the purity magnet so that a green raster positions in the center of screen.
  • Page 16 CPD-200GS Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. IBM AT Computer as a Jig D-sub (9 Pin [female]) *The parts above ( Convergence Rough Adjustment 1.

  • Page 17: Diagrams

    SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS CN310 4P WHT :S-MICRO CN311 3P WHT :S-MICRO CN305 8P DDC SCL DDC SCL WHT :S-MICRO DDC SDA DDC SDA +180V +180V HOST GND HOST GND CN307 9P WHT :S-MICRO +80V +80V IC006 IC001 IC002 J001 RGB PRE AMP...

  • Page 18: Schematic Diagrams Of D And J Boards

    (1) Schematic Diagrams of D and J Boards D BOARD IC801 TDA7053A • D BOARD WAVEFORMS 800 Vp-p (H) 120 Vp-p (H) 50.0 Vp-p (V) 2.0 Vp-p (V) 8.0 Vp-p (H) 4.0 Vp-p (H) TEMPERATURE Vref STABILAZER PROTECTION 6.0 Vp-p (24MHz) 1 3 11 15 •...
  • Page 19 AUDIO IN HEADPONE • D BOARD SEMICONDUCTOR LOCATION — J BOARD — Q901 C–2 – D616 A–3 – Q902 C–2 – D617 A–2 – Q903 D–1 – D618 A–3 – IC401 C–3 D621 B–3 – IC501 E–1 IC502 A–2 D622 B–3 –...

  • Page 20: Schematic Diagram Of A Board

    (2) Schematic Diagram of A Board (VIDEO) CN307 :S-MICRO D301 C301 1SS226 FL301 BGND JW(5) B:CHIP BLUE R301 C201 GGND 0.1 25V B:CHIP GREEN R201 FL201 RGND JW(5) R101 D101 C101 FL101 1SS226 JW(5) B:CHIP R016 :CHIP SIGNAL IN D001 HD15 RD5.6ES D003...
  • Page 21 — A BOARD — • A BOARD SEMICONDUCTOR LOCATION DIODE IC001 B–1 D001 C–2 – IC002 A–2 D003 C–1 – IC003 C–2 D014 C–3 – IC004 A–3 D101 C–1 IC005 B–3 D104 A–2 – IC006 C–1 D105 A–2 – D106 A–2 –...

  • Page 22: Semiconductors

    5-4. SEMICONDUCTORS 5-16...
  • Page 23 5-17...

  • Page 24: Exploded Views

    CPD-200GS • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. 6-1. CHASSIS 7-685-648-79 +BVTP 3X12 7-685-663-71...

  • Page 25: Packing Materials

    6-2. PACKING MATERIALS REF.NO. PART NO. DESCRIPTION * 4-061-802-01 CUSHION (UPPER)(ASSY) * 4-041-927-31 BAG, POLYETHYLENE * 4-061-803-01 CUSHION (LOWER)(ASSY) * 4-062-113-01 INDIVIDUAL CARTON [AUS model] * 4-061-801-01 INDIVIDUAL CARTON [CH model] The components identified by shading and mark Replace only with part number specified. 56 57 58 REMARK REF.NO.

  • Page 26: Electrical Parts List

    CPD-200GS REF.NO. PART NO. DESCRIPTION NOTE: The components identified by shading ¡ and mark are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board name. REF.NO. PART NO. DESCRIPTION * 8-933-301-00 A BOARD, COMPLETE **************************** 4-382-854-11 SCREW (M3X10), P, SW (+) (IC002, IC004) <CAPACITOR>...
  • Page 27 The components identified by shading ¡ and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION <FERRITE BEAD> FB001 1-412-911-11 FERRITE FB003 1-412-529-11 INDUCTOR 22UH FB004 1-412-911-11 FERRITE FB005 1-412-911-11 FERRITE FB006 1-412-911-11 FERRITE FB009 1-412-911-11 FERRITE FB010 1-412-911-11 FERRITE FB011 1-412-911-11 FERRITE...
  • Page 28 CPD-200GS REF.NO. PART NO. DESCRIPTION R333 1-247-807-31 CARBON R351 1-202-549-00 SOLID <SPARK GAP> SG001 1-519-422-11 GAP, SPARK SG101 1-517-499-21 GAP, SPARK SG201 1-517-499-21 GAP, SPARK SG301 1-517-499-21 GAP, SPARK ******************************************************************************** * 8-933-309-00 D BOARD, COMPLETE **************************** 2-371-561-00 BUSHING (P), INSULATING (IC503) 3-710-578-01 COVER, VOLUME, 6 MOLD 4-051-602-11 SHEET, RADIATION (IC503) 4-061-982-01 HOLDER, LED (D912)
  • Page 29 The components identified by shading ¡ and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION C578 1-117-214-11 CERAMIC 0.001MF C579 1-109-879-11 CERAMIC 22PF C580 1-137-370-11 FILM 0.01MF C582 1-126-964-11 ELECT 10MF C583 1-137-399-11 FILM 0.1MF C584 1-164-005-11 CERAMIC CHIP 0.47MF...
  • Page 30 CPD-200GS REF.NO. PART NO. DESCRIPTION CN902 1-564-513-11 PLUG, CONNECTOR 10P CN903*1-564-510-11 PLUG, CONNECTOR 7P <DIODE> D401 8-719-979-58 DIODE EGP10D D402 8-719-109-81 ZENER DIODE RD4.7ESB2 D403 8-719-911-19 DIODE 1SS119-25 D404 8-719-911-19 DIODE 1SS119-25 D501 8-719-110-31 ZENER DIODE RD12ESB2 D502 8-719-975-77 DIODE SB340 D503 1-215-437-00 METAL D504...
  • Page 31 The components identified by shading ¡ and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION ¡ FB614 1-412-911-21 FERRITE ¡ FB615 1-412-911-21 FERRITE FB616 1-412-911-11FERRITE ¡ FB618 1-412-911-21 FERRITE ¡ FB619 1-412-911-21 FERRITE FB654 1-412-911-11 FERRITE ¡...
  • Page 32 CPD-200GS REF.NO. PART NO. DESCRIPTION Q513 8-729-041-95 TRANSISTOR IRLI540GLF33 Q514 8-729-041-93 TRANSISTOR IRLI530GLF33 Q515 8-729-043-16 TRANSISTOR IRLI520GLF33 Q516 8-729-043-16 TRANSISTOR IRLI520GLF33 Q517 8-729-326-11 TRANSISTOR 2SC2611 Q518 8-729-140-50 TRANSISTOR 2SC3209LK Q519 8-729-119-78 TRANSISTOR 2SC2785-HFE Q520 8-729-042-23 TRANSISTOR IRFI9620GSLF35 Q521 8-729-119-76 TRANSISTOR 2SA1175-HFE Q522 8-729-119-76 TRANSISTOR 2SA1175-HFE Q523...
  • Page 33 The components identified by shading ¡ and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION R576 1-249-437-11 CARBON R577 1-216-445-11 METAL OXIDE 12 R578 1-216-423-11 METAL OXIDE 27 R579 1-247-887-00 CARBON 220K R580 1-216-681-11 METAL CHIP R581 1-249-429-11 CARBON...
  • Page 34 (NX-4400//J1L4) J1001 1-568-267-11 JACK (HEAD PHONE) J1002 1-568-267-21 JACK (AUDIO IN) <RESISTOR> R1001 1-249-403-11 CARBON R1002 1-249-403-11 CARBON Sony Corporation Display Company Computer Display Dept. – 44 – in this The components identified by shading The components identified by shading ¡...

Table of Contents