Related Manuals for Branick EF/HD
Summary of Contents for Branick EF/HD
- Page 1 MODEL EF/HD Installation, Operation Full Circle & Repair Parts Tire Spreader Information Branick Industries, Inc. • 4245 Main Avenue • Fargo, North Dakota 58103 P/N: 81-0199D REV060316...
- Page 2 TABLE OF CONTENTS _______________________________________________________ SAFETY INSTRUCTIONS DEFINITIONS INSTALLATION INSTRUCTIONS OPERATING INSTRUCTIONS MAINTENANCE REPAIR PARTS 4-14 REPAIR PARTS LIST 9-14 WARRANTY SAFETY INSTRUCTIONS _____________________________________________________ ▪ NEVER allow unauthorized personnel to operate this product. ▪ NEVER use this product for anything other than its intended use. ▪...
- Page 3 INSTALLATION_____________________________________________________________ 1) Position the Model eF/HD on a solid level floor leaving a minimum of 12 inches of clearance from rear and 24 inches of clearance from sides. The eF can be bolted down if desired using the four holes in bottom of frame.
- Page 4 WARNING Do not release the inner bead hooks (center valve) until the outer bead hooks have been released (right valve) and removed from tire. 5) To remove tire, release spread arm control valve (right valve) and remove outer bead hook. 6) Release pressure on inner bead hooks by stepping on diameter control valve (center valve).
- Page 5 REPAIR PARTS _____________________________________________________________ Model HD.EF General Assembly See parts list on page 9 & 10...
- Page 6 Diameter Arms & Linkage See parts list on page 9 & 10...
- Page 7 Lift Cradle Assembly See parts list on page 9 & 10...
- Page 8 Spread Arms Assembly See parts list on page 9 & 10...
- Page 9 Pneumatics See parts list on page 9 & 10...
- Page 10 REPAIR PARTS LIST ________________________________________________________ ITEM QTY PART NO. DESCRIPTION 03-0048 WELD, FOOT GUARD 03-0052 WELD, FITTING MOUNT 03-0219 WELD, VALVE MOUNT 03-0363 CONNECTOR, HDEF DIA. CYL. 028-006 SCREW, 1/2 X 2 NC H.H.C 028-017 SCREW, 1 X 1 3/4 N.C H.H.C 028-024 SCREW, 5/8 X 6 N.C H.H.C 028-089...
- Page 11 ITEM QTY PART NO. DESCRIPTION 101-197 PLATE 108-006 WASHER, 1/2 INTENAL LOCK 108-012 WASHER, 1 INT. LOCK 108-022 WASHER, 5/8 WROUGHT 110-011 SPRING, TENSION 111-030 BRACKET, INSIDE ARM 110-200 SPRING, SLEEVE 149-112 EQUALIZER ROD 157-003 WELDMENT, BELL CRANK 190-085 VALVE, QUICK EXHAUST 281-004 1 1/4 ROLLER 446-006...
- Page 12 Housing Assembly (900-037) ITEM QTY PART NO. DESCRIPTION 950-050 HOUSING SUB ASSY. 107-005 BALL RACE 107-043 THRUST BEARING RETAINER 489-003 REAR COLLAR 281-001 ROLLER BEARING 489-002 FRONT COLLAR 10-0018 VIBRATION MOUNT 055-145 5/16-18 NYLON LOCK NUT 028-022 3/8-16 X 3 HHC SCREW 055-123 3/8-16 NC HEX NUT 028-016...
- Page 13 Lift Cylinder Assembly (900-016) ITEM QTY PART NO. DESCRIPTION 006-004 1/4 CAP PLUG 098-005 LIFT CYLINDER COVER PLATE 110-007 LIFT CYLINDER SPRING 149-011 LIFT PISTON ROD 051-026 LIFT PISTON 041-295 4 PISTON CUP 101-296 CUP RETAINER 167-240 14mm GASKET 028-239 9/16-12 X 1 1/4 HHC SCREW 028-280 5/16-18 X 1/2 HHC SCREW...
- Page 14 Diameter Arm Cylinder Assembly (900-043) ITEM QTY PART NO. DESCRIPTION 006-004 1/4 CAP PLUG 264-001 DIA. ARM CYLINDER 104-002 PISTON SHAFT 051-016 5 1/4 PISTON 041-009 5 1/4 PISTON CUP 101-033 PISTON PLATE 028-013 9/16-12 X 1 3/4 HHC SCREW 167-240 14 mm GASKET 028-005...
- Page 15 Spread Cylinder Assembly (900-028) ITEM QTY PART NO. DESCRIPTION 028-034 1/2-13 X 1 1/4 HHC SCREW 006-004 1/4 CAP PLUG 098-004 COVER PLATE 251-002 950-107 SPREAD ARM PISTON AND ROD 041-009 5 1/4 PISTON CUP 101-033 PISTON PLATE 028-239 9/16-12 X 1 1/4 HHC SCREW 103-009 SPIDER ARM 149-021...
- Page 16 During the warranty period, at the discretion of Branick management, if the product is found to be defective, it will be repaired or replaced without charge. For service, contact Branick (800-437-4394) to obtain an RMA.
Need help?
Do you have a question about the EF/HD and is the answer not in the manual?
Questions and answers