Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for PXM PX361
- Page 1 PX361 PxGround 24ASF User manual...
-
Page 2: Table Of Contents
5 RDM – available parameters..............13 6 Connection scheme.................17 7 Dimensions....................19 8 Technical data..................19 Manufacturer reserves the right to make modifications in order to improve device operation. PXM Marek Żupnik sp.k. Podłęże 654 tel. +48 12 385 83 06 32-003 Podłęże mail: info@pxm.pl Rev.1-1 BDO register number 000005972 www.pxm.pl... -
Page 3: Description
PX361 light fixture uses high-performance LEDs offering multiple colour options and brightness levels. PX361 is available in an RGBN version. In addition, its universal design makes the fixture suitable for lighting both historical buildings and contemporary architecture. Maximum total wattage is 52W. The light fixture is equipped with optics designed for beam angles of 10°, 20°... -
Page 4: Safety Conditions
LEDs is limited. At 90°C, the light fixture fades out. In addition, the PX361 has a function Auto Power Regulation: When the total power of the channels starts to exceed 36W, the lamp automatically limits channel control while keeping proportions. - Page 5 Caution! Do not look at the LEDs at a shorter distance than 1.2m from the front surface of the tube without proper eye protection. LEDs can cause damage or eye irritation. Do not look at the light source directly through any optical instruments, which focus the light rays.
- Page 6 During its installation and use PX361 the following rules must be strictly observed: 1. Installation should be performed by a person holding the appropriate qualifications, according to the instruction manual. 2. Lamp may only be connected to stabilized voltage with current-carrying capacity compatible with technical data.
-
Page 7: Information On Version
Information on version The PX361 lamp is available in several versions that differ from each other in angles of the lenses used. Below there is a description of designation of the PX361 models and their explanation: PX361 – XX – RGBN XX –... -
Page 8: Illumination Installation
Illumination installation To install the illumination, proceed as described below, trying to arrange the components so that the order of re-assembly does not cause any problems. The correct arrangement of the sealing elements of the reflector is particularly important – the gaskets should properly adhere to their designated places. -
Page 9: Stage Ii: Lamp Assembly
4.2 Stage II: Lamp assembly 1. Unscrew 6 screws [6] on the front of the lamp. 2. Remove the upper ring [7] with the gasket [8]. 3. Carefully remove the glass [9]. 4. Remove the O-ring gasket [10]. 5. Install the lamp in a per-prepared position (4.5 Mounting the lamp in the ground) 6. -
Page 10: Components Of The Rear Part Of The Lamp
4.3 Components of the rear part of the lamp 1. 6 recessed screw with M5x10 cross recessed socket 2. M25x1.5 seal wire 3. Rear cover 4. O-ring gasket 160x6 5. Lamp body... -
Page 11: Components Of The Front Part Of The Lamp
4.4 Components of the front part of the lamp 6. 6 screw with M5x10 cross recessed socket 7. Upper ring 8. Flat seal 151x172x1 9. Tempered glass 10. O-ring gasket 160x6 11. Body housing... -
Page 12: Mounting The Lamp In The Ground
4.5 Mounting the lamp in the ground Ø213 Ø200 Ø192... -
Page 13: Rdm - Available Parameters
RDM – available parameters PX361 supports the DMX-RDM protocol. DMX protocol in its assumption enables one-way data flow while its extension, the RDM protocol, can transmit information in two ways. This makes the simultaneous receiving and sending of information possible and allows for monitoring the operation of devices compatible with the RDM protocol as well as gives the possibility of changing the configuration of their parameters. - Page 14 Parameter name Description additional device description, It is possible to enter an additional DEVICE_LABEL * 0x0082 device description using up to 32 ASCII characters. FACTORY_DEFAULTS 0x0090 device default settings DMX_PERSONALITY 0x00E0 DMX operational mode DMX_PERSONALITY_ description of individual 0x00E1 DESCRIPTION operational modes information concerning the SENSOR_DEFINITION...
- Page 15 Parameter name Description for value 0, the No signal mode is disabled, for 1 it is enabled. H – last DMX value hold, C – user created scene NO_SIGNAL: is implemented, R – red channel 0x801C 0|1|H|C|R|G|B|W|P * 100%, G – green channel 100%, B –...
- Page 16 Parameter name Description this is the rate of response to the disappearance of the DMX signal and transition to selected NoSignal SMOOTH_TIME_NOS * 0x8044 settings; The minimum value of the parameter is 10, the maximum is 2000. The default value is 100. the function that limits the total power of the lamp (total power of channels R, G, B and W).
-
Page 17: Connection Scheme
Connection scheme Single lamp Cross section B-B Controller e.g PX333 Power supply 24V DC (at least 52W) - Page 18 Connection of six PX361 lamps using the PX165 Splitter +24V DMX- DMX+ DMX+ DMX- +24V +24V DMX- DMX+ DMX+ DMX- +24V +24V DMX- DMX+ DMX+ DMX- +24V Controller e.g PX333 www.pxm.pl + + + – – – Power supply 12-24V DC...
-
Page 19: Dimensions
Dimensions min75 Technical data type PX361 number of LEDs light beam angle 10°, 20°, 35° LEDs colors RGBN number of DMX channels RDM protocol support power supply 24V DC max. power consumption IP rating IP67... - Page 20 casing material stainless steel (316L) weight 7.2kg diameter: 211mm dimensions height: 91mm...
- Page 21 Podłęże, 07.12.2018 DECLARATION OF CONFORMITY PXM Marek Żupnik spółka komandytowa Podłęże 654, 32-003 Podłęże we declare that our product: Product name: PxGround 24ASF Product code: PX361 meets the requirements of the following standards, as well as harmonised standards: PN-EN 50581:2013...
Need help?
Do you have a question about the PX361 and is the answer not in the manual?
Questions and answers