Related Manuals for Thytronic PRON NA60-CB0
Summary of Contents for Thytronic PRON NA60-CB0
- Page 1 PRON NA60-CB0 IEC 870-5-103 Communication Protocol User Guide PRON NA60-CB0 Version 2.00 Page: 1 of 15 PRON NA60-CB0 IEC 870-5-103...
-
Page 2: Table Of Contents
List of events produced by the relay ......................11 2.12 List of data contained in General Interrogation ..................13 2.13 Cyclic measurements ..........................14 2.14 List of the supported commands ........................ 15 Version 2.00 Page: 2 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 3: Iec 870-5-103 Protocol
PRON NA60-CB0 Introduction This Protocol Manual is for use with Thytronic Protective Relays, such as the DMC, NTG and PRO-N series that support the IEC 870-5-103 communication protocol. 1 IEC 870-5-103 Protocol The pages in this section have been extracted from the 60870-5-103 © IEC:1997, pages 159 to 171. -
Page 4: Application Layer
Local parameter setting <23> Characteristic 1 <24> Characteristic 2 <25> Characteristic 3 <26> Characteristic 4 <27> Auxiliary input 1 <28> Auxiliary input 2 <29> Auxiliary input 3 <30> Auxiliary input 4 Version 2.00 Page: 4 of 15 PRON NA60-CB0 IEC 870-5-103... - Page 5 Fault location X in ohms <74> Fault forward/line <75> Fault reverse/busbar <76> Teleprotection signal transmitted <77> Teleprotection signal received <78> Zone 1 <79> Zone 2 <80> Zone 3 <81> Zone 4 Version 2.00 Page: 5 of 15 PRON NA60-CB0 IEC 870-5-103...
- Page 6 Read value or attribute of a single entry <245> End of general interrogation of generic data <249> Write entry with confirmation <250> Write entry with execution <251> Write entry aborted Version 2.00 Page: 6 of 15 PRON NA60-CB0 IEC 870-5-103...
-
Page 7: Selection Of Standard Information Numbers In Control Direction
<249> Write entry with confirmation <250> Write entry with execution <251> Write entry abort 8.3.5 Basic application functions Test mode Blocking of monitor direction Disturbance data Generic services Private data Version 2.00 Page: 7 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 8: Miscellaneous
The parameters of the communication are the following : • Even Parity • 8 Data bits • 1 stop bit • Data rate 1200, 2400, 4800, 9600, 19200, 38400 or 57600 bauds Version 2.00 Page: 8 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 9: Initialisation
It should be noted that the measurands transmitted by the relay are sent as a proportion of either 1.2 or 2.4 times the rated value of the analogue value. The selection of either 1.2 or 2.4 for a particular value is indicated in 2.11. Version 2.00 Page: 9 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 10: Commands
The relay does not support a facility to block messages in the Monitor direction. 2.10 Acronyms FUN: Function Type INF: Information Number TYPE: Type of ASDU COT: Cause of Transmission BIDI: Bidirectional event Version 2.00 Page: 10 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 11: List Of Events Produced By The Relay
TRIP_PT4 Alarm ThAL5 ALARM_PT5 Trip Th>5 TRIP_PT5 Alarm ThAL6 ALARM_PT6 Trip Th>6 TRIP_PT6 Alarm ThAL7 ALARM_PT7 Trip Th>7 TRIP_PT7 Alarm ThAL8 ALARM_PT8 Trip Th>8 TRIP_PT8 Trip 74TCS TC_SUPERVISION Trip BF Version 2.00 Page: 11 of 15 PRON NA60-CB0 IEC 870-5-103... - Page 12 IN32 AUX_INPUT_32 IN33 AUX_INPUT_33 IN34 AUX_INPUT_34 IN35 AUX_INPUT_35 IN36 AUX_INPUT_36 IN37 AUX_INPUT_37 IN38 AUX_INPUT_38 IN39 AUX_INPUT_39 IN40 AUX_INPUT_40 IN41 AUX_INPUT_41 IN42 AUX_INPUT_42 General start I> GEN_START General trip I> GEN_TRIP Version 2.00 Page: 12 of 15 PRON NA60-CB0 IEC 870-5-103...
-
Page 13: List Of Data Contained In General Interrogation
IN28 AUX_INPUT_28 IN29 AUX_INPUT_29 IN30 AUX_INPUT_30 IN31 AUX_INPUT_31 IN32 AUX_INPUT_32 IN33 AUX_INPUT_33 IN34 AUX_INPUT_34 IN35 AUX_INPUT_35 IN36 AUX_INPUT_36 IN37 AUX_INPUT_37 IN38 AUX_INPUT_38 IN39 AUX_INPUT_39 IN40 AUX_INPUT_40 IN41 AUX_INPUT_41 IN42 AUX_INPUT_42 Version 2.00 Page: 13 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 14: Cyclic Measurements
9 , 8 2 MEASURAND_SET2 100^C 9 , 9 2 MEASURAND_SET2 100^C MEASURAND_SET2 9 , 10 100^C MEASURAND_SET2 9 , 11 100^C MEASURAND_SET2 9 , 12 100^C MEASURAND_SET2 9 , 13 Version 2.00 Page: 14 of 15 PRON NA60-CB0 IEC 870-5-103... -
Page 15: List Of The Supported Commands
PRON NA60-CB0 2.14 List of the supported commands LIST OF COMMANDS RATED NORMALIZE NAME VALUE FUN INF FACTOR TYPE LED_RESET OPEN_CB CLOSE_CB Version 2.00 Page: 15 of 15 PRON NA60-CB0 IEC 870-5-103...
Need help?
Do you have a question about the PRON NA60-CB0 and is the answer not in the manual?
Questions and answers