Summary of Contents for LogikaControl HTR
- Page 1 TEMPERATURE RECORDER (0 ÷ 300°C) Code 0KLC50BA INSTALLATION AND USE MANUAL Rev.1 dated 16-06-2014...
-
Page 2: Table Of Contents
INDEX Technical features page 3 Accessories supplied page 3 Accessories on request page 3 Caution page 4 Electrical drawing page 5 Programming page 6 Messages and alarm codes page 11 Enabling the device to record page 12 Download data page 13 Cleaning the device page 14 Disposal... -
Page 3: Technical Features
TECHNICAL FEATURES Power supply: 230 V ~ ± 15 % - 50/60Hz • Consumption: ~ 25 mA • Protection degree: • IP64 for the frontal panel IP20 for the other parts Working temperature: -5 ÷ +50°C with 90% RH non condensing •... -
Page 4: Caution
The electrical connection must be carried out by authorized personnel according the electrical drawing below and related legend and in power off status, so pay attention the isolator switch that HTR depends on the power supply is in OFF position. -
Page 5: Electrical Drawing
ELECTRICAL DRAWING LEGEND Terminal M1 poles 1-2 = power supply 230V~ Terminal M2 (serial port RS232) pole 1= GND pole 2 = TX pole 3 = RX pole 4 = out Vdc = 4,7 V Terminal M3 pole 1 (negative) – pole 2 (positive) = buffer battery Terminal M4 poles 1-2 = temperature probe –... -
Page 6: Programming
PROGRAMMING To program HTR and enable the recording, follow the instruction reported below. Once HTR is powered, the LCD visualizes the following message for few seconds: by Logika Control V. 00x (firmware release) and then visualize the picture nr. 1 below. - Page 7 Visualizations Visualizations Italian ° C 10:23 Thu 12/07/2007 DST/Standard time = YES By the buttoons and/or select the function to set and it will be visualized as reverse (from positive to negative): = language: Italian, English, French, German, Spanish, Greek, Portuguese – default English = temperature scale: °C / °F –...
- Page 8 P07 – High temperature alarm related to the probe T2: in the square on the right is possible to change the default value 300 °C (alarm disabled): setting range 0 ÷ 300 °C. P08 – Low temperature alarm related to the probe T2: in the square in the right is possible to change the default value 0 °C (alarm disabled): setting range 0 ÷...
- Page 9 Reset This function allows to enable the following reset (protected by password max. 4 numbers – default 0000): Confirm the function by and the LCD visualizes: Enter Password ---- by the buttons and/or enter the first number and confirm by to shift to the next one (the number just entered is changed into the symbol *);...
- Page 10 GSM module, the GSM will reply automatically with the message “NO ALARMS”, in case of no alarm detected or related codes in case of alarm detection. Symbols reported on the right low corner of the display of HTR connected to a GSM module: Antenna: the GSM is connected.
-
Page 11: Messages And Alarm Codes
Visualization with two temperature probes MESSAGES AND ALARM CODES Messages “Download data” due to: a) memory full (loop memory: once it’s full overwriting starts; last data erase the first one). b) change a parameter while data to download into the memory: disable recording and download the data before to modify any data. -
Page 12: Enabling The Device To Record
If one or more alarms are detected, the LCD visualizes the delta icon (generic alarm symbol) and related code; the relay contact closes between the poles 1-2 of the terminal Pushing and/or enter the alarm active list and you can flow up and down by the same arrow buttons;... -
Page 13: Download Data
For a right disposal ask for specialized companies. WARRANTY HTR temperature recorders are covered by a 24-months warranty against all manufacturing defects as from the production date printed on the label of the device identifying the year by the first 4 characters, the week by the second 2 characters and the progressive serial number with the last 5 characters. -
Page 14: Warranty
In case you need to use the service assistance during the warranty period, the product must be send back to the distributor you bought it paying attention it must be intact and packed into its original package. Customers are entitled to have defective products repaired, spare parts and labour included. Transport expenses and risk shall be met entirely by the Customer.